Hi Colleen,
Do you have all the FS aseg lables in your input segmentation file?
Lilla
________________________________
From: freesurfer-boun...@nmr.mgh.harvard.edu
<freesurfer-boun...@nmr.mgh.harvard.edu> on behalf of COLLEEN PLETCHER
<ccpletc...@medicine.wisc.edu>
Sent: Friday, April 23, 2021 3:01 PM
To: Freesurfer support list <freesurfer@nmr.mgh.harvard.edu>
Subject: Re: [Freesurfer] Infant Freesurfer exiting without error
External Email - Use Caution
Hi,
Just checking in about this question. Please let me know if you need anything
else from me!
Thanks,
Colleen
________________________________
From: freesurfer-boun...@nmr.mgh.harvard.edu
<freesurfer-boun...@nmr.mgh.harvard.edu> on behalf of COLLEEN PLETCHER
<ccpletc...@medicine.wisc.edu>
Sent: Tuesday, April 13, 2021 12:48 PM
To: Freesurfer support list <freesurfer@nmr.mgh.harvard.edu>
Subject: Re: [Freesurfer] Infant Freesurfer exiting without error
External Email - Use Caution
Hello,
I have attached the log file and the command used is the first line, please let
me know if you need anything else.
-Colleen
________________________________
From: freesurfer-boun...@nmr.mgh.harvard.edu
<freesurfer-boun...@nmr.mgh.harvard.edu> on behalf of Zollei, Lilla,Ph.D.
<lzol...@mgh.harvard.edu>
Sent: Tuesday, April 13, 2021 12:33 PM
To: freesurfer@nmr.mgh.harvard.edu <freesurfer@nmr.mgh.harvard.edu>
Subject: Re: [Freesurfer] Infant Freesurfer exiting without error
Hi Colleen,
Can you send the exact command that you used and also the log file for more
information?
Best, Lilla
________________________________
From: freesurfer-boun...@nmr.mgh.harvard.edu
<freesurfer-boun...@nmr.mgh.harvard.edu> on behalf of COLLEEN PLETCHER
<ccpletc...@medicine.wisc.edu>
Sent: Tuesday, April 13, 2021 1:29 PM
To: freesurfer@nmr.mgh.harvard.edu <freesurfer@nmr.mgh.harvard.edu>
Subject: [Freesurfer] Infant Freesurfer exiting without error
External Email - Use Caution
Hi,
I am trying to run infant freesurfer using the --segfile and --masked options.
When I attempt to run it, it runs for a bit and then I get this:
USAGE: mri_or <options> fname1 fname2 ..
After this, the program exits. I am not getting any error, so I am confused
about why it is exiting suddenly?
Thank you very much!
-Colleen
_______________________________________________
Freesurfer mailing list
Freesurfer@nmr.mgh.harvard.edu
https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
The information in this e-mail is intended only for the person to whom it is
addressed. If you believe this e-mail was sent to you in error and the e-mail
contains patient information, please contact the Mass General Brigham
Compliance HelpLine at http://www.massgeneralbrigham.org/complianceline . If
the e-mail was sent to you in error but does not contain patient information,
please contact the sender and properly dispose of the e-mail.
Please note that this e-mail is not secure (encrypted). If you do not wish to
continue communication over unencrypted e-mail, please notify the sender of
this message immediately. Continuing to send or respond to e-mail after
receiving this message means you understand and accept this risk and wish to
continue to communicate over unencrypted e-mail.
