2010/9/26 David DEMELIER <demelier.da...@gmail.com>: > 2010/9/26 Andriy Gapon <a...@icyb.net.ua>: >> on 26/09/2010 20:37 David DEMELIER said the following: >>> mark...@melon ~ $ sudo camcontrol devlist >>> <WDC WD3200BEKT-60F3T1 12.01A12> at scbus0 target 0 lun 0 (ada0) >>> <hp DVDRAM GT20L DC05> at scbus1 target 0 lun 0 (cd0) >>> >>> mark...@melon ~ $ sudo cdrecord >>> downloads/FreeBSD-8.1-RELEASE-amd64-livefs.iso >>> cdrecord: No write mode specified. >>> cdrecord: Assuming -sao mode. >>> cdrecord: If your drive does not accept -sao, try -tao. >>> cdrecord: Future versions of cdrecord may have different drive >>> dependent defaults. >>> Cdrecord-ProDVD-ProBD-Clone 3.00 (amd64-unknown-freebsd8.1) Copyright >>> (C) 1995-2010 Jörg Schilling >>> cdrecord: Error 0. Cannot open or use SCSI driver. >>> cdrecord: For possible targets try 'cdrecord -scanbus'. >>> cdrecord: For possible transport specifiers try 'cdrecord dev=help'. >>> >>> mark...@melon ~ $ sudo cdrecord -scanbus >>> Cdrecord-ProDVD-ProBD-Clone 3.00 (amd64-unknown-freebsd8.1) Copyright >>> (C) 1995-2010 Jörg Schilling >>> cdrecord: Error 0. Cannot open or use SCSI driver. >>> cdrecord: For possible targets try 'cdrecord -scanbus'. >>> cdrecord: For possible transport specifiers try 'cdrecord dev=help'. >> >> Doesn't look like you have xpt and pass devices in your kernel, which are >> (almost) mandatory when use CAM-based drivers. >> Not sure if ahci(4) mentions this. >> >> -- >> Andriy Gapon >> > > Everything works now… Sorry for the noise ! > > We can close the PR too. > > -- > Demelier David >
or not, mark...@melon ~ $ sudo cdrecord downloads/FreeBSD-8.1-RELEASE-i386-livefs.iso cdrecord: No write mode specified. cdrecord: Assuming -sao mode. cdrecord: If your drive does not accept -sao, try -tao. cdrecord: Future versions of cdrecord may have different drive dependent defaults. Cdrecord-ProDVD-ProBD-Clone 3.00 (amd64-unknown-freebsd8.1) Copyright (C) 1995-2010 Jörg Schilling Using libscg version 'schily-0.9'. No target specified, trying to find one... Using dev=1,0,0. Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'hp ' Identifikation : 'DVDRAM GT20L ' Revision : 'DC05' Device seems to be: Generic mmc2 DVD-R/DVD-RW/DVD-RAM. Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R LAYER_JUMP Starting to write CD/DVD/BD at speed 24 in real SAO mode for single session. Last chance to quit, starting real write 0 seconds. Operation starts. cdrecord: WARNING: Drive returns wrong startsec (0) using -150 cdrecord: Input/output error. write_g1: scsi sendcmd: retryable error CDB: 2A 00 FF FF FF 6A 00 00 20 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Sense Key: 0xFFFFFFFF [], Segment 0 Sense Code: 0x00 Qual 0x00 (no additional sense information) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 11.961s timeout 200s write track pad data: error after 0 bytes BFree: 597 K BSize: 597 K cdrecord: Input/output error. write_g1: scsi sendcmd: retryable error CDB: 2A 00 00 00 00 00 00 00 20 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Sense Key: 0xFFFFFFFF [], Segment 0 Sense Code: 0x00 Qual 0x00 (no additional sense information) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 0.001s timeout 200s write track data: error after 0 bytes cdrecord: A write error occured. cdrecord: Please properly read the error message above. I will rollback to the old working ata driver. -- Demelier David _______________________________________________ freebsd-stable@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "freebsd-stable-unsubscr...@freebsd.org"
