Here is a question....When looking at the pci address list, I have two
National Intruments devices showing....1 is the DIO96 card, The other is
named bridge. The "bridge" shows 3 different I/O registers. Do I write the
driver to talk to the bridge? I noticed a file called plx9030.h in the
source. The bridge device is a plx9030. how would I use this or do I even
need to?
Dave
----- Original Message -----
From: "Dave Keeton" <[EMAIL PROTECTED]>
To: "Enhanced Machine Controller (EMC)" <[email protected]>
Sent: Friday, May 16, 2008 12:43 AM
Subject: Re: [Emc-users] Installing on Hardy Heron
>I modified the pci_8255 driver and renamed it to pci_dio96 then compiled it
> into EMC. I called the new driver in my cofig and it did show up with the
> proper number of pins in hal show. Have'nt tested it yet but I do expect
> some hurdles. The first time it lock up the computer completely while
> loading EMC. I fixed a booboo and it loaded normally after that. I have a
> little learning curve but I am on my way. Thank you for all your help so
> far. If I can make this work it will give us 96 more IO points to play
> with........Any future help is welcomed and appreciated...
>
> Dave
>
> ----- Original Message -----
> From: "Dave Keeton" <[EMAIL PROTECTED]>
> To: "Enhanced Machine Controller (EMC)" <[email protected]>
> Sent: Thursday, May 15, 2008 10:35 PM
> Subject: Re: [Emc-users] Installing on Hardy Heron
>
>
>> Thank you! That is a big help....
>>
>> Dave
>>
>> ----- Original Message -----
>> From: "Stephen Wille Padnos" <[EMAIL PROTECTED]>
>> To: "Enhanced Machine Controller (EMC)" <[email protected]>
>> Sent: Thursday, May 15, 2008 10:24 PM
>> Subject: Re: [Emc-users] Installing on Hardy Heron
>>
>>
>>> Dave Keeton wrote:
>>>
>>>>Since I'm still working on that driver for my DIO96, Is it very
>>>>difficult
>>>>to
>>>>compile the new driver into emc? I am fairly new at C programming so
>>>>this
>>>>is
>>>>a learning experience for me.....
>>>>
>>>>
>>> Install the developer tools:
>>> sudo apt-get install emc2-dev
>>>
>>> Maybe also install all the EMC build dependencies (though I don't think
>>> it's necessary):
>>> sudo apt-get build-dep emc2
>>>
>>> Then write some C or comp code (man comp for more info, also you can
>>> look at all the comps in the emc source after `apt-get source emc2`),
>>> and install it with:
>>> sudo comp --install mycode.c
>>> or sudo comp --install mycode.comp
>>>
>>> Not too hard, especially if you have DSL or cable for the package
>>> downloads :)
>>>
>>> Oh, there's a wiki page:
>>> <http://wiki.linuxcnc.org/cgi-bin/emcinfo.pl?HowToWriteNewHalComponent>
>>>
>>> - Steve
>>> [snip]
>>>
>>>
>>> -------------------------------------------------------------------------
>>> This SF.net email is sponsored by: Microsoft
>>> Defy all challenges. Microsoft(R) Visual Studio 2008.
>>> http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
>>> _______________________________________________
>>> Emc-users mailing list
>>> [email protected]
>>> https://lists.sourceforge.net/lists/listinfo/emc-users
>>>
>>
>>
>> -------------------------------------------------------------------------
>> This SF.net email is sponsored by: Microsoft
>> Defy all challenges. Microsoft(R) Visual Studio 2008.
>> http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
>> _______________________________________________
>> Emc-users mailing list
>> [email protected]
>> https://lists.sourceforge.net/lists/listinfo/emc-users
>>
>
>
> -------------------------------------------------------------------------
> This SF.net email is sponsored by: Microsoft
> Defy all challenges. Microsoft(R) Visual Studio 2008.
> http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
> _______________________________________________
> Emc-users mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/emc-users
>
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Emc-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/emc-users
