While I pay close attention to the Guide, I am doubtful that going against its guidance to, in effect, over document, is sufficient to invalidate a DoC.
I have not ever encountered resistance to listing both MSD and LVD---has anyone on this listserv? Mike Sherman > On 01/17/2022 10:54 AM Charles Grasso <[email protected]> wrote: > > > Other that the fact that the statement is "the manufacturer’s EC > Declaration of > conformity shall not refer to the LVD but to the MD".? > > My guess is that you could invalidate the DoC if you violate that > requirement. > > > Chas > > On Mon, Jan 17, 2022 at 9:41 AM Oliver Betz <[email protected] > mailto:[email protected] > wrote: > > > > This message originated outside of DISH and was sent by: > [email protected] mailto:[email protected] > > > > Hi all, > > > > the "Guide to application of the Machinery Directive 2006/42/EC", > > Edition 2.2: https://ec.europa.eu/docsroom/documents/38022 states: > > > > "...Thus, whilst machinery with an electrical supply, which is not > > in > > any of the categories listed in Article 1(2) (k) of MD, shall > > fulfil the > > safety objectives of the LVD, the manufacturer’s EC Declaration of > > conformity shall not refer to the LVD but to the MD". > > > > Yet, EN60204-1:2018 is listed in the LVD summary of harmonised > > standards. > > > > Would it harm to state also the LVD conformity in a DoC for > > machinery? > > > > The above mentioned guide writes that the DoC "shall *not* refer to > > the > > LVD but to the MD" but I'm not sure about the intention behind. > > > > And we have problems with Turkish customs insisting that the DoC > > shall > > list also LVD compliance. > > > > I wonder whether / how I can phrase an elegant note on the LVD > > compliance. > > > > Any ideas? > > > > Oliver > > > > - > > ---------------------------------------------------------------- > > This message is from the IEEE Product Safety Engineering Society > > emc-pstc discussion list. To post a message to the list, send your e-mail > > to <[email protected] mailto:[email protected] > > > > > All emc-pstc postings are archived and searchable on the web at: > > http://www.ieee-pses.org/emc-pstc.html > > > > Attachments are not permitted but the IEEE PSES Online Communities > > site at http://product-compliance.oc.ieee.org/ can be used for graphics (in > > well-used formats), large files, etc. > > > > Website: http://www.ieee-pses.org/ > > Instructions: http://www.ieee-pses.org/list.html (including how to > > unsubscribe) > > List rules: http://www.ieee-pses.org/listrules.html > > > > For help, send mail to the list administrators: > > Scott Douglas <[email protected] mailto:[email protected] > > > Mike Cantwell <[email protected] mailto:[email protected] > > > > > For policy questions, send mail to: > > Jim Bacher: <[email protected] mailto:[email protected] > > > David Heald: <[email protected] mailto:[email protected] > > > > > > > > -- > > Charles Grasso > > Dish Technologies > > (c) 303-204-2974 > > (h) 303-317-5530 > > (e ) [email protected] mailto:[email protected] > > (e2) [email protected] mailto:[email protected] > > - > ---------------------------------------------------------------- > > This message is from the IEEE Product Safety Engineering Society emc-pstc > discussion list. To post a message to the list, send your e-mail to > <[email protected] mailto:[email protected] > > > All emc-pstc postings are archived and searchable on the web at: > http://www.ieee-pses.org/emc-pstc.html > > Attachments are not permitted but the IEEE PSES Online Communities site > at http://product-compliance.oc.ieee.org/ can be used for graphics (in > well-used formats), large files, etc. > > Website: http://www.ieee-pses.org/ > Instructions: http://www.ieee-pses.org/list.html (including how to > unsubscribe) http://www.ieee-pses.org/list.html > List rules: http://www.ieee-pses.org/listrules.html > > For help, send mail to the list administrators: > Scott Douglas <[email protected] mailto:[email protected] > > Mike Cantwell <[email protected] mailto:[email protected] > > > For policy questions, send mail to: > Jim Bacher <[email protected] mailto:[email protected] > > David Heald <[email protected] mailto:[email protected] > > - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe) List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]> Mike Cantwell <[email protected]> For policy questions, send mail to: Jim Bacher: <[email protected]> David Heald: <[email protected]>
