Make sure you have removed the old IP addresses from ethX as well On Thu, May 3, 2012 at 1:37 AM, 星言 墨虚 <beyond1...@yahoo.cn> wrote:
> I have assigned IP address to br0, and let OpenvSwitch to connect > controller. I can find the ARP Request packet and ARP Reply packet between > OpenvSwitch and NOX by wireshark. But there are only ARP packets between > them and controller still cannot recognize OpenvSwitch. > > Is there anything wrong with my congfigure? > > Thanks. > > -- Tony > > ------------------------------ > *发件人：* Justin Pettit <jpet...@nicira.com> > *收件人：* 星言 墨虚 <beyond1...@yahoo.cn> > *抄送：* ovs-discuss <discuss@openvswitch.org> > *发送日期：* 2012年5月3日, 星期四, 下午 4:10 > *主题:* Re: 回复： 回复： 回复： [ovs-discuss] 回复： How to configure in-band control > in OpenvSwitch? > > You must be using an older version of OVS if you don't have that command. > In any case, if the bridge is there, you should be able to set an IP > address on it. You'll need to do more debugging or be more forthcoming > with information about what you've done and what you're seeing. > > --Justin > > > On May 3, 2012, at 12:58 AM, 星言 墨虚 wrote: > > > The picture is the screenshot by "ovs-dpctl show". And there isn't a > command named "ovs-vsctl show", so I use "ovs-dpctl show". > > And it looks right. > > > > Thanks. > > > > -- Tony > > > > 发件人： Justin Pettit <jpet...@nicira.com> > > 收件人： 星言 墨虚 <beyond1...@yahoo.cn> > > 抄送： ovs-discuss <discuss@openvswitch.org> > > 发送日期： 2012年5月3日, 星期四, 下午 3:47 > > 主题: Re: 回复： 回复： [ovs-discuss] 回复： How to configure in-band control in > OpenvSwitch? > > > > Your configuration looks reasonable. However, there should be no > problem assigning an IP address to the bridge device, and it won't work > properly if you assign addresses to interfaces that are members of the > bridge. What does "ovs-vsctl show" print out? > > > > --Justin > > > > > > On May 3, 2012, at 12:35 AM, 星言 墨虚 wrote: > > > > > I can assign IP address to eth0 and eth1, but I cannot assign IP > address to br0, because br0 was a virtual port that was create by > openvswitch, and cannot be find in ifconfig. > > > Another question, when I run openvswitch, eth1 of B cannot connect > controller. But if I didn't run openvswitch, it can connect controller. > > > > > > I use kernel model of openvswitch like this. > > > > > > # /sbin/insmod datapath/linux-2.6/openvswitch_mod.ko > > > # ovsdb-server /usr/local/etc/ovs-switchd.conf.db > --remote=punix:/usr/local/var/run/openvswitch/db.sock > --remote=db:Open_vSwitch,managers --detach > > > # ovs-vswitchd unix:/usr/local/var/run/openvswitch/db.sock > > > > > > Thanks. > > > > > > -- Tony > > > > > > 发件人： Justin Pettit <jpet...@nicira.com> > > > 收件人： 星言 墨虚 <beyond1...@yahoo.cn> > > > 抄送： Ben Pfaff <b...@nicira.com>; ovs-discuss <discuss@openvswitch.org> > > > 发送日期： 2012年5月3日, 星期四, 下午 3:26 > > > 主题: Re: 回复： [ovs-discuss] 回复： How to configure in-band control in > OpenvSwitch? > > > > > > You don't need to do it with OVS commands. You can just use ifconfig, > ip, dhclient... > > > > > > --Justin > > > > > > > > > On May 3, 2012, at 12:21 AM, 星言 墨虚 wrote: > > > > > > > But I cannot find a command of ovs-vsctl could assign the IP address > to bridge just like br0. > > > > So how to add an IP address to br0? > > > > > > > > Thanks. > > > > > > > > -- Tony > > > > > > > > 发件人： Justin Pettit <jpet...@nicira.com> > > > > 收件人： 星言 墨虚 <beyond1...@yahoo.cn> > > > > 抄送： Ben Pfaff <b...@nicira.com>; ovs-discuss <discuss@openvswitch.org> > > > > > 发送日期： 2012年5月3日, 星期四, 下午 2:23 > > > > 主题: Re: [ovs-discuss] 回复： How to configure in-band control in > OpenvSwitch? > > > > > > > > Even B can't connect to the controller? That should be pretty basic > connectivity. Are the IP addresses on the devices attached to the bridge or > the bridge itself? Based on your drawing it looks like they're on the > devices, which won't work. What happens if you assign the IP addresses to > the bridge? > > > > > > > > --Justin > > > > > > > > > > > > On May 2, 2012, at 11:13 PM, 星言 墨虚 <beyond1...@yahoo.cn> wrote: > > > > > > > >> Thanks, but I want to know how to add "hidden" rules to OpenvSwitch? > > > >> For example, > > > >> > > > >> A(eth0) -------- (eth0)B(eth1) ------ (eth0)controller > > > >> 10.0.0.1 10.0.0.2 11.0.0.1 11.0.0.2 > > > >> > > > >> I create a network like this. A and B is openvswitch. I configure > openvswitch using this command > > > >> ovs-vsctl add-br br0 > > > >> ovs-vsctl add-port br0 eth0 > > > >> ovs-vsctl add-port br0 eth1 > > > >> ovs-vsctl set-controller br0 tcp:11.0.0.2:6633 > > > >> > > > >> But, the openvswitches cannot connect to controller, what else > should I do? > > > >> > > > >> -- Tony > > > >> 发件人： Ben Pfaff <b...@nicira.com> > > > >> 收件人： 星言 墨虚 <beyond1...@yahoo.cn> > > > >> 抄送： "discuss@openvswitch.org" <discuss@openvswitch.org> > > > >> 发送日期： 2012年5月3日, 星期四, 上午 11:30 > > > >> 主题: Re: [ovs-discuss] How to configure in-band control in > OpenvSwitch? > > > >> > > > >> On Thu, May 03, 2012 at 11:12:50AM +0800, 星言 墨虚 wrote: > > > >> > I want to configure OpenvSwitch in-band control and I read > > > >> > the Design Decisions In Open vSwitch which websit is > > > >> > > http://openvswitch.org/cgi-bin/gitweb.cgi?p=openvswitch;a=blob;f=DESIGNBut > > > >> > there are not details about how to enable in-band control in > > > >> > OpenvSwitch.So, I want to know the steps to configure it.Thanks > very > > > >> > much.-- Tony > > > >> > > > >> You don't have to do anything to enable in-band control, because it > is > > > >> enabled by default. > > > >> > > > >> > > > >> _______________________________________________ > > > >> discuss mailing list > > > >> discuss@openvswitch.org > > > >> http://openvswitch.org/mailman/listinfo/discuss > > > > > > > > > > > > > > > > > > > > > > > > > <Screenshot.png> > > > > > _______________________________________________ > discuss mailing list > discuss@openvswitch.org > http://openvswitch.org/mailman/listinfo/discuss > >
_______________________________________________ discuss mailing list discuss@openvswitch.org http://openvswitch.org/mailman/listinfo/discuss
