You must be using an older version of OVS if you don't have that command. In any case, if the bridge is there, you should be able to set an IP address on it. You'll need to do more debugging or be more forthcoming with information about what you've done and what you're seeing.
--Justin On May 3, 2012, at 12:58 AM, 星言 墨虚 wrote: > The picture is the screenshot by "ovs-dpctl show". And there isn't a command > named "ovs-vsctl show", so I use "ovs-dpctl show". > And it looks right. > > Thanks. > > -- Tony > > 发件人： Justin Pettit <jpet...@nicira.com> > 收件人： 星言 墨虚 <beyond1...@yahoo.cn> > 抄送： ovs-discuss <discuss@openvswitch.org> > 发送日期： 2012年5月3日, 星期四, 下午 3:47 > 主题: Re: 回复： 回复： [ovs-discuss] 回复： How to configure in-band control in > OpenvSwitch? > > Your configuration looks reasonable. However, there should be no problem > assigning an IP address to the bridge device, and it won't work properly if > you assign addresses to interfaces that are members of the bridge. What does > "ovs-vsctl show" print out? > > --Justin > > > On May 3, 2012, at 12:35 AM, 星言 墨虚 wrote: > > > I can assign IP address to eth0 and eth1, but I cannot assign IP address to > > br0, because br0 was a virtual port that was create by openvswitch, and > > cannot be find in ifconfig. > > Another question, when I run openvswitch, eth1 of B cannot connect > > controller. But if I didn't run openvswitch, it can connect controller. > > > > I use kernel model of openvswitch like this. > > > > # /sbin/insmod datapath/linux-2.6/openvswitch_mod.ko > > # ovsdb-server /usr/local/etc/ovs-switchd.conf.db > > --remote=punix:/usr/local/var/run/openvswitch/db.sock > > --remote=db:Open_vSwitch,managers --detach > > # ovs-vswitchd unix:/usr/local/var/run/openvswitch/db.sock > > > > Thanks. > > > > -- Tony > > > > 发件人： Justin Pettit <jpet...@nicira.com> > > 收件人： 星言 墨虚 <beyond1...@yahoo.cn> > > 抄送： Ben Pfaff <b...@nicira.com>; ovs-discuss <discuss@openvswitch.org> > > 发送日期： 2012年5月3日, 星期四, 下午 3:26 > > 主题: Re: 回复： [ovs-discuss] 回复： How to configure in-band control in > > OpenvSwitch? > > > > You don't need to do it with OVS commands. You can just use ifconfig, ip, > > dhclient... > > > > --Justin > > > > > > On May 3, 2012, at 12:21 AM, 星言 墨虚 wrote: > > > > > But I cannot find a command of ovs-vsctl could assign the IP address to > > > bridge just like br0. > > > So how to add an IP address to br0? > > > > > > Thanks. > > > > > > -- Tony > > > > > > 发件人： Justin Pettit <jpet...@nicira.com> > > > 收件人： 星言 墨虚 <beyond1...@yahoo.cn> > > > 抄送： Ben Pfaff <b...@nicira.com>; ovs-discuss <discuss@openvswitch.org> > > > 发送日期： 2012年5月3日, 星期四, 下午 2:23 > > > 主题: Re: [ovs-discuss] 回复： How to configure in-band control in OpenvSwitch? > > > > > > Even B can't connect to the controller? That should be pretty basic > > > connectivity. Are the IP addresses on the devices attached to the bridge > > > or the bridge itself? Based on your drawing it looks like they're on the > > > devices, which won't work. What happens if you assign the IP addresses to > > > the bridge? > > > > > > --Justin > > > > > > > > > On May 2, 2012, at 11:13 PM, 星言 墨虚 <beyond1...@yahoo.cn> wrote: > > > > > >> Thanks, but I want to know how to add "hidden" rules to OpenvSwitch? > > >> For example, > > >> > > >> A(eth0) -------- (eth0)B(eth1) ------ (eth0)controller > > >> 10.0.0.1 10.0.0.2 11.0.0.1 11.0.0.2 > > >> > > >> I create a network like this. A and B is openvswitch. I configure > > >> openvswitch using this command > > >> ovs-vsctl add-br br0 > > >> ovs-vsctl add-port br0 eth0 > > >> ovs-vsctl add-port br0 eth1 > > >> ovs-vsctl set-controller br0 tcp:11.0.0.2:6633 > > >> > > >> But, the openvswitches cannot connect to controller, what else should I > > >> do? > > >> > > >> -- Tony > > >> 发件人： Ben Pfaff <b...@nicira.com> > > >> 收件人： 星言 墨虚 <beyond1...@yahoo.cn> > > >> 抄送： "discuss@openvswitch.org" <discuss@openvswitch.org> > > >> 发送日期： 2012年5月3日, 星期四, 上午 11:30 > > >> 主题: Re: [ovs-discuss] How to configure in-band control in OpenvSwitch? > > >> > > >> On Thu, May 03, 2012 at 11:12:50AM +0800, 星言 墨虚 wrote: > > >> > I want to configure OpenvSwitch in-band control and I read > > >> > the Design Decisions In Open vSwitch which websit is > > >> > http://openvswitch.org/cgi-bin/gitweb.cgi?p=openvswitch;a=blob;f=DESIGNBut > > >> > there are not details about how to enable in-band control in > > >> > OpenvSwitch.So, I want to know the steps to configure it.Thanks very > > >> > much.-- Tony > > >> > > >> You don't have to do anything to enable in-band control, because it is > > >> enabled by default. > > >> > > >> > > >> _______________________________________________ > > >> discuss mailing list > > >> discuss@openvswitch.org > > >> http://openvswitch.org/mailman/listinfo/discuss > > > > > > > > > > > > > > > > <Screenshot.png> _______________________________________________ discuss mailing list discuss@openvswitch.org http://openvswitch.org/mailman/listinfo/discuss
