i'm seeing only LED's D and F are on, because host pc is not at all detecting the hardware and i'm unable to run any operation.In my first i mentioned the errors what i'am getting when i run the flowgraph. Even i'am clueless how my device is only showing up 10/100Mbps when i connect the hardware and even i tried with other pc but i'm facing the same problem.
Thanks and regards Sandhya On Mon, Oct 21, 2013 at 10:42 AM, Activecat <active...@gmail.com> wrote: > What operating are you running? How do you get the "10/100Mbps" ? Do you > see the LED turns on at the USRP GE port? > > > On Mon, Oct 21, 2013 at 1:09 PM, Sandhya G <sandhya4...@gmail.com> wrote: > >> Sir my pc is capable of supporting 1000Mbps but when i connect the >> hardware and check the speed of the port it will be showing 10/100Mbps. >> What might the issue?and can i boost the pc speed >> >> Thanks and regards >> Sandhya >> >> >> On Mon, Oct 21, 2013 at 10:30 AM, Sandhya G <sandhya4...@gmail.com>wrote: >> >>> ya its a new one and sir y i'am i getting unknown key format even though >>> i give addr=192.168.10.2 and the problem i'm facing is its showing me an >>> error has cannot find as a single device.I have no clue the reason for that >>> >>> Thanks and regards >>> Sandhya >>> >>> >>> On Mon, Oct 21, 2013 at 10:24 AM, Activecat <active...@gmail.com> wrote: >>> >>>> If that is a new USRP from factory then you don't need to update the >>>> firmware. >>>> >>>> >>>> >>>> On Mon, Oct 21, 2013 at 12:51 PM, Sandhya G <sandhya4...@gmail.com>wrote: >>>> >>>>> Thanks for the reply. >>>>> Well is that only problem so that i'm unable to communicate and should >>>>> i need to update the firmware? >>>>> >>>>> >>>>> Thanks and regards >>>>> Sandhya.G >>>>> >>>>> >>>>> On Mon, Oct 21, 2013 at 10:19 AM, Activecat <active...@gmail.com>wrote: >>>>> >>>>>> Your pc must have 1000Mbps port. The 10/100Mbps won't work. >>>>>> An alternative is to connect a 10/100/1000 LAN switch between your pc >>>>>> and the USRP. >>>>>> >>>>>> Rgds, >>>>>> activecat. >>>>>> >>>>>> >>>>>> On Mon, Oct 21, 2013 at 12:37 PM, Sandhya G <sandhya4...@gmail.com>wrote: >>>>>> >>>>>>> HI all, >>>>>>> >>>>>>> >>>>>>> I have followed as per the instructions given in the webpage for set >>>>>>> up of the Usrp N200/N210 but still i am unable to communicate between >>>>>>> the >>>>>>> hardware and host pc >>>>>>> >>>>>>> >>>>>>> >>>>>>> 1.I have set the static ip of the host pc to >>>>>>> 192.168.10.1(ifconfig eth0 192.168.10.1). >>>>>>> >>>>>>> 2.Whenever i give the device address=addr=192.168.10.1 and run the >>>>>>> grc i am getting the error has “*unknown key format*” >>>>>>> >>>>>>> 3.Whenever i ping 192.168.10.2 or use the command uhb_find_device >>>>>>> i am getting warning as “*NO DEVICE FOUND* “ >>>>>>> >>>>>>> 4. Is that a must i have to upload the fpga and firmware images when >>>>>>> using the device for the first time. >>>>>>> >>>>>>> 5.Sometimes i am getting an error like”* unable to find as single >>>>>>> device”.* >>>>>>> >>>>>>> *6.*The* *host pc is supporting only 10/100MBPS .Is that the only >>>>>>> problem so that i am unable to communicate with the hardware. >>>>>>> >>>>>>> >>>>>>> >>>>>>> Can anybody help me on this issue.Awaiting for your valuable reply >>>>>>> >>>>>>> >>>>>>> Thanks in advance >>>>>>> >>>>>>> Sandhya.G >>>>>>> >>>>>>> _______________________________________________ >>>>>>> Discuss-gnuradio mailing list >>>>>>> Discuss-gnuradio@gnu.org >>>>>>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio >>>>>>> >>>>>>> >>>>>> >>>>> >>>> >>> >> >
_______________________________________________ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
