What operating are you running? How do you get the "10/100Mbps" ? Do you see the LED turns on at the USRP GE port?
On Mon, Oct 21, 2013 at 1:09 PM, Sandhya G <sandhya4...@gmail.com> wrote: > Sir my pc is capable of supporting 1000Mbps but when i connect the > hardware and check the speed of the port it will be showing 10/100Mbps. > What might the issue?and can i boost the pc speed > > Thanks and regards > Sandhya > > > On Mon, Oct 21, 2013 at 10:30 AM, Sandhya G <sandhya4...@gmail.com> wrote: > >> ya its a new one and sir y i'am i getting unknown key format even though >> i give addr=192.168.10.2 and the problem i'm facing is its showing me an >> error has cannot find as a single device.I have no clue the reason for that >> >> Thanks and regards >> Sandhya >> >> >> On Mon, Oct 21, 2013 at 10:24 AM, Activecat <active...@gmail.com> wrote: >> >>> If that is a new USRP from factory then you don't need to update the >>> firmware. >>> >>> >>> >>> On Mon, Oct 21, 2013 at 12:51 PM, Sandhya G <sandhya4...@gmail.com>wrote: >>> >>>> Thanks for the reply. >>>> Well is that only problem so that i'm unable to communicate and should >>>> i need to update the firmware? >>>> >>>> >>>> Thanks and regards >>>> Sandhya.G >>>> >>>> >>>> On Mon, Oct 21, 2013 at 10:19 AM, Activecat <active...@gmail.com>wrote: >>>> >>>>> Your pc must have 1000Mbps port. The 10/100Mbps won't work. >>>>> An alternative is to connect a 10/100/1000 LAN switch between your pc >>>>> and the USRP. >>>>> >>>>> Rgds, >>>>> activecat. >>>>> >>>>> >>>>> On Mon, Oct 21, 2013 at 12:37 PM, Sandhya G <sandhya4...@gmail.com>wrote: >>>>> >>>>>> HI all, >>>>>> >>>>>> >>>>>> I have followed as per the instructions given in the webpage for set >>>>>> up of the Usrp N200/N210 but still i am unable to communicate between the >>>>>> hardware and host pc >>>>>> >>>>>> >>>>>> >>>>>> 1.I have set the static ip of the host pc to >>>>>> 192.168.10.1(ifconfig eth0 192.168.10.1). >>>>>> >>>>>> 2.Whenever i give the device address=addr=192.168.10.1 and run the >>>>>> grc i am getting the error has “*unknown key format*” >>>>>> >>>>>> 3.Whenever i ping 192.168.10.2 or use the command uhb_find_device i >>>>>> am getting warning as “*NO DEVICE FOUND* “ >>>>>> >>>>>> 4. Is that a must i have to upload the fpga and firmware images when >>>>>> using the device for the first time. >>>>>> >>>>>> 5.Sometimes i am getting an error like”* unable to find as single >>>>>> device”.* >>>>>> >>>>>> *6.*The* *host pc is supporting only 10/100MBPS .Is that the only >>>>>> problem so that i am unable to communicate with the hardware. >>>>>> >>>>>> >>>>>> >>>>>> Can anybody help me on this issue.Awaiting for your valuable reply >>>>>> >>>>>> >>>>>> Thanks in advance >>>>>> >>>>>> Sandhya.G >>>>>> >>>>>> _______________________________________________ >>>>>> Discuss-gnuradio mailing list >>>>>> Discuss-gnuradio@gnu.org >>>>>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio >>>>>> >>>>>> >>>>> >>>> >>> >> >
_______________________________________________ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
