Signed-off-by: Ben Pfaff <b...@nicira.com>
---
FAQ | 93 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 93 insertions(+), 0 deletions(-)
diff --git a/FAQ b/FAQ
index bdd96ce..7cba6f0 100644
--- a/FAQ
+++ b/FAQ
@@ -168,6 +168,99 @@ A: Tunnel and patch virtual ports are not supported, as
described in the
may not be transmitted.
+Basic Configuration
+-------------------
+
+Q: How do I configure a port as an access port?
+
+A: Add "tag=VLAN" to your "ovs-vsctl add-port" command. For example,
+ the following commands configure br0 with eth0 as a trunk port (the
+ default) and tap0 as an access port for VLAN 9:
+
+ ovs-vsctl add-br br0
+ ovs-vsctl add-port br0 eth0
+ ovs-vsctl add-port br0 tap0 tag=9
+
+ If you want to configure an already added port as an access port,
+ use "ovs-vsctl set", e.g.:
+
+ ovs-vsctl set port tap0 tag=9
+
+Q: How do I configure a port as a SPAN port, that is, enable mirroring
+ of all traffic to that port?
+
+A: The following commands configure br0 with eth0 and tap0 as trunk
+ ports. All traffic coming in or going out on eth0 or tap0 is also
+ mirrored to tap1; any traffic arriving on tap1 is dropped:
+
+ ovs-vsctl add-br br0
+ ovs-vsctl add-port br0 eth0
+ ovs-vsctl add-port br0 tap0
+ ovs-vsctl add-port br0 tap1 \
+ -- --id=@p get port tap1 \
+ -- --id=@m create mirror name=m0 select-all=true output-port=@p \
+ -- set bridge br0 mirrors=@m
+
+ To later disable mirroring, run:
+
+ ovs-vsctl clear bridge br0 mirrors
+
+Q: How do I configure a VLAN as an RSPAN VLAN, that is, enable
+ mirroring of all traffic to that VLAN?
+
+A: The following commands configure br0 with eth0 as a trunk port and
+ tap0 as an access port for VLAN 10. All traffic coming in or going
+ out on tap0, as well as traffic coming in or going out on eth0 in
+ VLAN 10, is also mirrored to VLAN 15 on eth0:
+
+ ovs-vsctl add-br br0
+ ovs-vsctl add-port br0 eth0
+ ovs-vsctl add-port br0 tap0 tag=10
+ ovs-vsctl \
+ -- --id=@m create mirror name=m0 select-vlan=10 output-vlan=15 \
+ -- set bridge br0 mirrors=@m
+
+ (If you omit select-vlan=10, then all traffic on any VLAN, except
+ VLAN 15, will be mirrored to VLAN 15. This is possibly confusing
+ because the packets' original VLANs cannot be determined.)
+
+ To later disable mirroring, run:
+
+ ovs-vsctl clear bridge br0 mirrors
+
+ Mirroring to a VLAN can disrupt a network that contains unmanaged
+ switches. See ovs-vswitchd.conf.db(5) for details. Mirroring to a
+ GRE tunnel has fewer caveats than mirroring to a VLAN and should
+ generally be preferred.
+
+Q: How do I configure mirroring of all traffic to a GRE tunnel?
+
+A: The following commands configure br0 with eth0 and tap0 as trunk
+ ports. All traffic coming in or going out on eth0 or tap0 is also
+ mirrored to gre0, a GRE tunnel to the remote host 192.168.1.10; any
+ traffic arriving on gre0 is dropped:
+
+ ovs-vsctl add-br br0
+ ovs-vsctl add-port br0 eth0
+ ovs-vsctl add-port br0 tap0
+ ovs-vsctl add-port br0 gre0 \
+ -- set interface gre0 type=gre options:remote_ip=192.168.1.10 \
+ -- --id=@p get port gre0 \
+ -- --id=@m create mirror name=m0 select-all=true output-port=@p \
+ -- set bridge br0 mirrors=@m
+
+ To later disable mirroring and destroy the GRE tunnel:
+
+ ovs-vsctl clear bridge br0 mirrors
+ ovs-vcstl del-port br0 gre0
+
+Q: Does Open vSwitch support ERSPAN?
+
+A: No. ERSPAN is an undocumented proprietary protocol. As an
+ alternative, Open vSwitch supports mirroring to a GRE tunnel (see
+ above).
+
+
Configuration Problems
----------------------
--
1.7.2.5
_______________________________________________
dev mailing list
dev@openvswitch.org
http://openvswitch.org/mailman/listinfo/dev
