The current AXGBE code assumes that offset 6 of EEPROM SFP DAC (passive)
cables is NULL. However, some cables (the 5 meter and 7 meter Molex
passive cables) have non-zero data at offset 6. Fix the logic by moving
the passive cable check above the active checks, so as not to be
improperly identified as an active cable. This will fix the issue for
any passive cable that advertises 1000Base-CX in offset 6.
Without the fix the user will not get link UP for few DAC cables.
Fixes: a5c7273771e8 ("net/axgbe: add phy programming APIs")
Cc: sta...@dpdk.org
Signed-off-by: Venkat Kumar Ande <venkatkumar.a...@amd.com>
---
drivers/net/axgbe/axgbe_phy_impl.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/net/axgbe/axgbe_phy_impl.c
b/drivers/net/axgbe/axgbe_phy_impl.c
index 9c2ae7bba0..d4c4a89517 100644
--- a/drivers/net/axgbe/axgbe_phy_impl.c
+++ b/drivers/net/axgbe/axgbe_phy_impl.c
@@ -625,7 +625,10 @@ static void axgbe_phy_sfp_parse_eeprom(struct axgbe_port
*pdata)
}
/* Determine the type of SFP */
- if (sfp_base[AXGBE_SFP_BASE_10GBE_CC] & AXGBE_SFP_BASE_10GBE_CC_SR)
+ if (phy_data->sfp_cable == AXGBE_SFP_CABLE_PASSIVE &&
+ axgbe_phy_sfp_bit_rate(sfp_eeprom, AXGBE_SFP_SPEED_10000))
+ phy_data->sfp_base = AXGBE_SFP_BASE_10000_CR;
+ else if (sfp_base[AXGBE_SFP_BASE_10GBE_CC] & AXGBE_SFP_BASE_10GBE_CC_SR)
phy_data->sfp_base = AXGBE_SFP_BASE_10000_SR;
else if (sfp_base[AXGBE_SFP_BASE_10GBE_CC] & AXGBE_SFP_BASE_10GBE_CC_LR)
phy_data->sfp_base = AXGBE_SFP_BASE_10000_LR;
@@ -642,9 +645,6 @@ static void axgbe_phy_sfp_parse_eeprom(struct axgbe_port
*pdata)
phy_data->sfp_base = AXGBE_SFP_BASE_1000_CX;
else if (sfp_base[AXGBE_SFP_BASE_1GBE_CC] & AXGBE_SFP_BASE_1GBE_CC_T)
phy_data->sfp_base = AXGBE_SFP_BASE_1000_T;
- else if ((phy_data->sfp_cable == AXGBE_SFP_CABLE_PASSIVE) &&
- axgbe_phy_sfp_bit_rate(sfp_eeprom, AXGBE_SFP_SPEED_10000))
- phy_data->sfp_base = AXGBE_SFP_BASE_10000_CR;
switch (phy_data->sfp_base) {
case AXGBE_SFP_BASE_1000_T:
--
2.34.1
