Hi Anoob, Do you need any more info.. Kindly help us.. We are totally stuck.. Thanks
On Wed, 19 Aug, 2020, 4:38 pm satyavalli rama, <satyavalli.r...@gmail.com> wrote: > Hi Anoob > > We are using the following hardware details, > HOST: x722 (i40e) intel. > VM: e1000 (82540) intel. > > We have launched Virtual machine on host , and executing ipsec-secgw > application on VM. > > Please find below the CLI and configuration for TRANSPORT MODE. > > CLI: > > ./build/ipsec-secgw -l 0 -n 4 --socket-mem 1024,0 --vdev "crypto_null" -- > -p 0x3 -P -u 0x1 --config="(0,0,0),(1,0,0)" -f ep0.cfg > > #TRANSPORT: > > #SP IPv4 rules > sp ipv4 out esp protect 10 pri 1 dst 192.168.122.0/24 sport 0:65535 dport > 0:65535 > > #SA rules > sa out 10 cipher_algo aes-128-cbc cipher_key > a1:a1:a1:a1:a1:a1:a1:a1:a1:a1:a1:\ > a1:a1:a1:a1:a1 auth_algo sha1-hmac auth_key > a1:a1:a1:a1:a1:a1:a1:a1:a1:a1:a1:\ > a1:a1:a1:a1:a1:a1:a1:a1:a1 mode transport > > #Routing rules > rt ipv4 dst 192.168.122.0/24 port 1 > > > Please find below the CLI and configuration for TUNNEL MODE. > > CLI: > > ./build/ipsec-secgw -l 0 -n 4 --socket-mem 1024,0 --vdev "crypto_null" -- > -p 0x3 -P -u 0x1 --config="(0,0,0),(1,0,0)" -f ep0.cfg > > #TUNNEL End Point-0: > > #SP IPv4 rules > sp ipv4 out esp protect 5 pri 1 dst 192.168.122.0/24 sport 0:65535 dport > 0:65535 > > #SA rules > sa out 5 cipher_algo aes-128-cbc cipher_key > 0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0 \ > auth_algo sha1-hmac auth_key 0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0 \ > mode ipv4-tunnel src 192.168.122.96 dst 192.168.122.213 > > #Routing rules > rt ipv4 dst 192.168.122.0/24 port 1 > > On Tue, 18 Aug, 2020, 4:29 pm Anoob Joseph, <ano...@marvell.com> wrote: > >> Hi Satya, >> >> Are you attempting to enable inline protocol (IPsec) functionality? If >> yes, which PMD (& h/w) are you using for the same? >> >> Thanks, >> Anoob >> >> > -----Original Message----- >> > From: dev <dev-boun...@dpdk.org> On Behalf Of satyavalli rama >> > Sent: Tuesday, August 18, 2020 4:08 PM >> > To: dev@dpdk.org; us...@dpdk.org >> > Subject: Re: [dpdk-dev] Ipsec-secgw packet processing >> > >> > We further debugged and we observed that while running ipsec-secgw >> > application in transport-mode dpdk-19.02/11, we found that inline packet >> > processing is not happening. >> > We observed that ol_flags is not setting from driver level. We are >> expecting >> > that , because of ol_flags not set , inline packet processing is not >> > happening.Any idea What could be the reason for this, I think ol_flags >> will be >> > configured from driver level Or else do we need to provide any external >> > configuration for setting ol_flags. >> > And also we are not observing encrypt/decrypt packets on pdump before >> > sending packets out from tx-port(rte_eth_tx_burst()). >> > Please help us on this...to proceed further. >> > >> > Thanks & Regards >> > Satya >> > >> > >> > >> > On Mon, 17 Aug, 2020, 4:11 pm satyavalli rama, < >> satyavalli.r...@gmail.com> >> > wrote: >> > >> > > >> > > Hello, >> > > >> > > While we are running ipsec-secgw application in transport-mode on >> > > dpdk-19.02, we found that inline packet processing is not happening. >> > > >> > > And also we are not observing any encrypt/decrypt packets on pdump >> > > before sending packets out from tx-port(rte_eth_tx_burst()). >> > > >> > > Please help us on how to proceed further. >> > > >> > > Thanks, >> > > Jagadeesh >> > > >> > > >> >
