Hi Anoob We are using the following hardware details, HOST: x722 (i40e) intel. VM: e1000 (82540) intel.
We have launched Virtual machine on host , and executing ipsec-secgw application on VM. Please find below the CLI and configuration for TRANSPORT MODE. CLI: ./build/ipsec-secgw -l 0 -n 4 --socket-mem 1024,0 --vdev "crypto_null" -- -p 0x3 -P -u 0x1 --config="(0,0,0),(1,0,0)" -f ep0.cfg #TRANSPORT: #SP IPv4 rules sp ipv4 out esp protect 10 pri 1 dst 192.168.122.0/24 sport 0:65535 dport 0:65535 #SA rules sa out 10 cipher_algo aes-128-cbc cipher_key a1:a1:a1:a1:a1:a1:a1:a1:a1:a1:a1:\ a1:a1:a1:a1:a1 auth_algo sha1-hmac auth_key a1:a1:a1:a1:a1:a1:a1:a1:a1:a1:a1:\ a1:a1:a1:a1:a1:a1:a1:a1:a1 mode transport #Routing rules rt ipv4 dst 192.168.122.0/24 port 1 Please find below the CLI and configuration for TUNNEL MODE. CLI: ./build/ipsec-secgw -l 0 -n 4 --socket-mem 1024,0 --vdev "crypto_null" -- -p 0x3 -P -u 0x1 --config="(0,0,0),(1,0,0)" -f ep0.cfg #TUNNEL End Point-0: #SP IPv4 rules sp ipv4 out esp protect 5 pri 1 dst 192.168.122.0/24 sport 0:65535 dport 0:65535 #SA rules sa out 5 cipher_algo aes-128-cbc cipher_key 0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0 \ auth_algo sha1-hmac auth_key 0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0 \ mode ipv4-tunnel src 192.168.122.96 dst 192.168.122.213 #Routing rules rt ipv4 dst 192.168.122.0/24 port 1 On Tue, 18 Aug, 2020, 4:29 pm Anoob Joseph, <ano...@marvell.com> wrote: > Hi Satya, > > Are you attempting to enable inline protocol (IPsec) functionality? If > yes, which PMD (& h/w) are you using for the same? > > Thanks, > Anoob > > > -----Original Message----- > > From: dev <dev-boun...@dpdk.org> On Behalf Of satyavalli rama > > Sent: Tuesday, August 18, 2020 4:08 PM > > To: dev@dpdk.org; us...@dpdk.org > > Subject: Re: [dpdk-dev] Ipsec-secgw packet processing > > > > We further debugged and we observed that while running ipsec-secgw > > application in transport-mode dpdk-19.02/11, we found that inline packet > > processing is not happening. > > We observed that ol_flags is not setting from driver level. We are > expecting > > that , because of ol_flags not set , inline packet processing is not > > happening.Any idea What could be the reason for this, I think ol_flags > will be > > configured from driver level Or else do we need to provide any external > > configuration for setting ol_flags. > > And also we are not observing encrypt/decrypt packets on pdump before > > sending packets out from tx-port(rte_eth_tx_burst()). > > Please help us on this...to proceed further. > > > > Thanks & Regards > > Satya > > > > > > > > On Mon, 17 Aug, 2020, 4:11 pm satyavalli rama, < > satyavalli.r...@gmail.com> > > wrote: > > > > > > > > Hello, > > > > > > While we are running ipsec-secgw application in transport-mode on > > > dpdk-19.02, we found that inline packet processing is not happening. > > > > > > And also we are not observing any encrypt/decrypt packets on pdump > > > before sending packets out from tx-port(rte_eth_tx_burst()). > > > > > > Please help us on how to proceed further. > > > > > > Thanks, > > > Jagadeesh > > > > > > >
