Hi Bob, I have not, I gave it a little bit force and it "rocked" slightly. I just didn't want to break anything. Are they built with dowel pins? are those two outer holes for the dowel pins?
Bo On Tue, Apr 13, 2021 at 5:37 PM Bob Mann via CnC-List <cnc-list@cnc-list.com> wrote: > Handrail is probably epoxied onto deck. Have you tried sliding a putty > knife beneath each section? > > On 04/13/2021 5:07 PM General Gao via CnC-List <cnc-list@cnc-list.com> > wrote: > > > mine is wood external handrail. In the picture in this link, the hole in > the middle is where in the cabin handrail screw goes in; the two on the > outside were hidden under the cabin handrail, exposed after I took the it > off. I tried to see and feel, there was no metal inside. > > > https://drive.google.com/file/d/1bS3eUTqnZ3ZGLnMtNmKw2Q4gB7Emy8UN/view?usp=sharing > > Am I missing something? Advice would be appreciated. > > Thx. > > Bo > > On Tue, Apr 13, 2021 at 1:26 PM Charlie Nelson via CnC-List < > cnc-list@cnc-list.com> wrote: > > Mine and likely others have nuts welded(SS) or pressed (wood) into the > external handrail standoffs. > > Thus a bolt/screw on the inside screws into these nuts--more or less! > > I say this because depending on how well the cabin-top holes match the > external hand rail standoffs, it may not be possible to get a bolt/screw > into each standoff. If this is the case, some of the standoffs may not have > bolts/screws in them. > > In my case, with SS steel external rails and standoffs, there is no way to > get a misaligned screw hole to accept a nut or screw, without re drilling a > new hole or enlarging the original one. > > Charlie Nelson > > > > -----Original Message----- > From: General Gao via CnC-List <cnc-list@cnc-list.com> > To: Stus-List <cnc-list@cnc-list.com> > Cc: General Gao <general.z....@gmail.com> > Sent: Tue, Apr 13, 2021 12:51 pm > Subject: Stus-List Re: handrail > > So I took the handrail inside the cabin off, exposed the holes hidden, I > assume those are for the handrail outside the cabin. There seems to be no > screws in those holes. Is the outside handrail attached to the cabin with > screws or something? Mine isn’t coming off yet. > > Thx > > Bo > > On Mon, Mar 29, 2021 at 12:21 WILLIAM WALKER via CnC-List < > cnc-list@cnc-list.com> wrote: > > > Agree, I said glue but always use varnish. > Bill Walker > > On Monday, March 29, 2021, 06:47:16 AM EDT, James Hesketh via CnC-List < > cnc-list@cnc-list.com> wrote: > > > > > WILLIAM wrote: > > snip >> > > > After the glue dries use a Sharp chisel to level, a little sandpaper and > the apply finish. > > > I'd always been told it's better to set bungs (the plugs) by dipping them > in varnish before tapping them into place. That way, the varnish will act > as a waterproofer and semi-adhesive, but then they can be removed easily > next time. With glue they would need to be drilled out. > > Jim Hesketh > C&C 26 Whisper > Miami, FL > > > Thanks to all of the subscribers that contributed to the list to help with > the costs involved. If you want to show your support to the list - use > PayPal to send contribution -- https://www.paypal.me/stumurray Thanks - > Stu > Thanks to all of the subscribers that contributed to the list to help with > the costs involved. If you want to show your support to the list - use > PayPal to send contribution -- https://www.paypal.me/stumurray Thanks > - Stu > > > Thanks to all of the subscribers that contributed to the list to help with > the costs involved. If you want to show your support to the list - use > PayPal to send contribution -- https://www.paypal.me/stumurray Thanks - > Stu > Thanks to all of the subscribers that contributed to the list to help with > the costs involved. If you want to show your support to the list - use > PayPal to send contribution -- https://www.paypal.me/stumurray Thanks > - Stu > > Thanks to all of the subscribers that contributed to the list to help with > the costs involved. If you want to show your support to the list - use > PayPal to send contribution -- https://www.paypal.me/stumurray Thanks - > Stu > > Thanks to all of the subscribers that contributed to the list to help with > the costs involved. If you want to show your support to the list - use > PayPal to send contribution -- https://www.paypal.me/stumurray Thanks > - Stu
Thanks to all of the subscribers that contributed to the list to help with the costs involved. If you want to show your support to the list - use PayPal to send contribution -- https://www.paypal.me/stumurray Thanks - Stu
