FYI – it doesn’t hurt to use 2 vacuum gauges, one before the filter and one after. I was experiencing high vacuum and shutdowns and after I installed the second gauge, I found high vacuum on BOTH of them. It wasn’t the filter that was clogged, it was the pickup tube in the tank. The filter’s contribution to the problem is the difference between the gauges ;) My clog turned out to be rubber pieces from the fuel fill hose, it was slowly dissolving and dropping bits of rubber into the tank. Sometimes they would suck onto the fuel pickup and sometimes they would drop back off.
Joe Della Barba Coquina C&C 35 MK I www.dellabarba.com From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Wade Glew via CnC-List Sent: Friday, May 29, 2020 9:52 AM To: cnc-list@cnc-list.com Cc: Wade Glew <wadeg...@gmail.com> Subject: [EXTERNAL] Re: Stus-List Diesel Filter thanks for this Josh Wade Oh Boy 33-2 On Sun, May 24, 2020 at 11:16 PM Josh Muckley via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: Wade, Look at the picture of a 500 series racor in the link below. The factory top has a t handle which is used to tighten the lid. The vacuum gauge which Joe linked replaces that t-handle. The t arms are not used to sense pressure - just for tightening the lid. https://www.ebay.com/itm/172954061164 BTW: these 500 series are notorious for being easily over tightened which warps the lid and causes leaks. The 500 series is 60gph which would be close to 60 times the flow capacity required for any one of our engines. Even with a 2 micron filter I would not expect much if any vacuum being formed, though it should be noted that the vacuum represents the effort required to "lift" the fuel out of the tank AND the effort required to suck the fuel through the filter. Yanmar typically rates their engines for up to 10 feet of lift. Diesel is 34" per psi so 10 feet = ~3.5 psi. Even with no filter element installed the vacuum for 10 feet of vertical lift of diesel fuel would amount to 100 inH2O, 3.5psia or 7 inHg. Josh Muckley S/V Sea Hawk 1989 C&C 37+ Solomons, MD On Sun, May 24, 2020, 23:03 Wade Glew via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: Hi Joe Looking at the guage you've linked to, its obvious the "T" arms go in the fuel line between the Racor and engine. Where does the threaded base of the T go? What is a normal pressure? What pressure reading makes you decide to change filters? Are the lined just clamped with small hose clamps or what? Wade Oh Boy 33-2 On Sun, May 24, 2020, 17:15 Joe Della Barba via CnC-List, <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: A vacuum gauge is one of the best cost/benefit ratio improvements you can do. You can save a lot of $$$ in unneeded filter changes and get advanced warning when you do need to change one. Be official: https://www.ebay.com/sch/i.html?_from=R40&_trksid=m570.l1313&_nkw=racor+gauge&_sacat=0 Cockpit mount with light: https://moyermarine.com/product/vacuum-gauge-kit-gaug_07-1_532/<https://protect2.fireeye.com/v1/url?k=b7f37aed-ea80e98c-b7f3539a-ac1f6b44e86e-4c178e1e039dd85e&q=1&e=7cb8c88e-efc3-44b3-82bf-4503afac93d7&u=https%3A%2F%2Fmoyermarine.com%2Fproduct%2Fvacuum-gauge-kit-gaug_07-1_532%2F> (also can be used for manifold vacuum) Cheap: https://www.ebay.com/itm/2-1-2-Vacuum-Gauge-Chrome-Plated-Steel-Case-1-4-NPT-Lower-Mnt-30-inHg-0/183642544745?hash=item2ac1f2da69:g:2gUAAOSwJiBcQOWz https://www.ebay.com/itm/LIQUID-FILLED-VACUUM-GAUGE-30-0-PSI-2-5-FACE-1-4-NPT-LOWER-MOUNT-WOG/192746480989?hash=item2ce095e55d:g:RiQAAOSwqoxcBW9S Joe Coquina C&C 35 MK I On 5/24/2020 3:39 PM, bwhitmore via CnC-List wrote: Time and again I have read that Yanmar does not recommend a 2/3 micron primary filter. I therefore use a 10 micron, and use Biobar, as well as some Seafoam. I have some old crud in my tank, but where I can see it through the hole for the sender, the bits I can see are pretty well stuck to the bottom of the tank (and there are not many of them). That said, the boat had sat at the dock for +/- 6 years before I got her, and we have run 150 gallons or so of fuel through the boat in the last 4 years. I change my Racor every year, and I used to change the one on the engine every year as well. This time, I'm going to let the engine mounted one go another year. We still get a fine layer of black "grit" at the bottom of the racor over the year, but it does not appear to hinder the running of the engine. I'd rather swap out a $20 filter once a year than risk the engine shutting down as I go through a bridge opening with 3 kts. of current. To each their own, Bruce _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
_______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
