Re: Stus-List Keel treatment

Thu, 03 May 2018 16:59:02 -0700

Neill, I've always wetsanded the lead with West Systems epoxy. Then sanded for tooth and applied bottom paint. No issues so far. 

Chris Price 

On May 3, 2018 at 5:26 PM Neil Gallagher via CnC-List <cnc-list@cnc-list.com> wrote:

Richard,

I'm dealing with exactly the same issue, had the bottom soda blasted to bare lead and what's left of my gelcoat.  I called Interlux about this, their tech rep recommended Interprotect 2000E on both the hull and the lead.  For the lead he recommended thinning the first coat 15%-20% with their 2333N thinner so it will flow into the cracks, as some of my keel's a bit rough.  Then you can fair it and build it up with more barrier coat (the 2000E).

Neil Gallagher
Weatherly, 35-1
Glen Cove, NY


On 5/3/2018 5:11 PM, bushmark4--- via CnC-List wrote:
To the group; I have removed all of the old bottom paint and some old faring compound from my keel and it is now down to bare lead; what should I use for a sealant/primer on the bare metal, before putting on a barrier coat, and what is the best method for application?  I have also taken the hull to gelcoat and plan to put on a barrier coat and new bottom paint...any other ideas...? Many thanks...


Richard
s/v Bushmark4: 1985 C&C 37 CB; on the hard...

Richard N. Bush Law Offices
2950 Breckenridge Lane, Suite Nine
Louisville, Kentucky 40220-1462
502-584-7255


-----Original Message-----
From: Josh Muckley via CnC-List <cnc-list@cnc-list.com>
To: C&C List <cnc-list@cnc-list.com>
Cc: Josh Muckley <muckl...@gmail.com>
Sent: Thu, May 3, 2018 1:33 pm
Subject: Re: Stus-List Yanmar 2gmf

Send us a picture.

Josh Muckley
S/V Sea Hawk 
1989 C&C 37+
Solomons, MD 

On Thu, May 3, 2018, 12:21 PM Bev Parslow via CnC-List <cnc-list@cnc-list.com> wrote:
Seem to be loosing some fuel. The tank is good. There is no leak from the tank to the primary filter. It then goes to the engine. No leak there. Pardon my ignorance but there is a round attachment with a gasket on the top that seems to be leaking. There are some small  screws? bolts? holding it down. It seems to be oozing from there. Can I tighten them leaving everything together or do I need to take the mixing elbow off?
Yanmar 2gmf.
_______________________________________________

Thanks everyone for supporting this list with your contributions.  Each and every one is greatly appreciated.  If you want to support the list - use PayPal to send contribution --   https://www.paypal.me/stumurray

_______________________________________________

Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray



_______________________________________________

Thanks everyone for supporting this list with your contributions.  Each and every one is greatly appreciated.  If you want to support the list - use PayPal to send contribution --   https://www.paypal.me/stumurray


 

_______________________________________________

Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray

_______________________________________________

Thanks everyone for supporting this list with your contributions.  Each and 
every one is greatly appreciated.  If you want to support the list - use PayPal 
to send contribution --   https://www.paypal.me/stumurray

Reply via email to