Richard

A few years back when I fixed the C&C smile I took my keel down to the bare 
lead.  At that time I read some where that epoxy wouldn’t stick to the lead 
unless it was free of oxidation.  Hard to do with lead.  I also learned that 
the best way to apply the epoxy and get it to bond was to use a wire brush.  I 
put a wire brush on my drill and polished the lead and immediately applied the 
epoxy.  Once the base coat was on I just followed normal epoxy instructions.  
Did that probably 10 years ago and when I applied the bottom paint yesterday 
everything looked liked it did way back when.

Mike
PERSUASION
C&C 37 K/CB
Long Sault

> On May 3, 2018, at 5:11 PM, bushmark4--- via CnC-List <cnc-list@cnc-list.com> 
> wrote:
> 
> To the group; I have removed all of the old bottom paint and some old faring 
> compound from my keel and it is now down to bare lead; what should I use for 
> a sealant/primer on the bare metal, before putting on a barrier coat, and 
> what is the best method for application?  I have also taken the hull to 
> gelcoat and plan to put on a barrier coat and new bottom paint...any other 
> ideas...? Many thanks...
> 
> 
> Richard
> s/v Bushmark4: 1985 C&C 37 CB; on the hard...
> 
> Richard N. Bush Law Offices 
> 2950 Breckenridge Lane, Suite Nine
> Louisville, Kentucky 40220-1462 
> 502-584-7255
> 
> 
> -----Original Message-----
> From: Josh Muckley via CnC-List <cnc-list@cnc-list.com>
> To: C&C List <cnc-list@cnc-list.com>
> Cc: Josh Muckley <muckl...@gmail.com>
> Sent: Thu, May 3, 2018 1:33 pm
> Subject: Re: Stus-List Yanmar 2gmf
> 
> Send us a picture.
> 
> Josh Muckley
> S/V Sea Hawk 
> 1989 C&C 37+
> Solomons, MD 
> 
> On Thu, May 3, 2018, 12:21 PM Bev Parslow via CnC-List 
> <cnc-list@cnc-list.com> wrote:
> Seem to be loosing some fuel. The tank is good. There is no leak from the 
> tank to the primary filter. It then goes to the engine. No leak there. Pardon 
> my ignorance but there is a round attachment with a gasket on the top that 
> seems to be leaking. There are some small  screws? bolts? holding it down. It 
> seems to be oozing from there. Can I tighten them leaving everything together 
> or do I need to take the mixing elbow off?
> Yanmar 2gmf.
> _______________________________________________
> 
> Thanks everyone for supporting this list with your contributions.  Each and 
> every one is greatly appreciated.  If you want to support the list - use 
> PayPal to send contribution --   https://www.paypal.me/stumurray
> 
> _______________________________________________
> 
> Thanks everyone for supporting this list with your contributions. Each and 
> every one is greatly appreciated. If you want to support the list - use 
> PayPal to send contribution -- https://www.paypal.me/stumurray
> 
> _______________________________________________
> 
> Thanks everyone for supporting this list with your contributions.  Each and 
> every one is greatly appreciated.  If you want to support the list - use 
> PayPal to send contribution --   https://www.paypal.me/stumurray
> 
_______________________________________________

Thanks everyone for supporting this list with your contributions.  Each and 
every one is greatly appreciated.  If you want to support the list - use PayPal 
to send contribution --   https://www.paypal.me/stumurray

Reply via email to