Edd When my linear drive start acting sporadic it was the brushes. By sporadic I mean the autopilot would turn the wheel to come back on course then it would let go and just hold the last correction. Sometimes it would just go straight sometimes it wanted to do circles. The brushes were worn out and only made contacted with the armature occasionally. Could not buy the brushes anywhere. Ended up ordering oversized ones on line and filing them to fit. That was over two years ago and no issues since.
Mike PERSUASION C&C 37 K/CB Long Sault > On Jul 17, 2017, at 10:33 AM, Edd Schillay via CnC-List > <cnc-list@cnc-list.com> wrote: > > All, > > Thanks. I’m thinking it must be the connections and will double-check those. > I could see the heading reading in the upper right corner of the display, so > I know there were no issues with the fluxgate. I also don’t think it w the > belt as the wheel drive is new and has less than two hours of total use on it > — additionally, the motor was not reacting — not like it was whirring and > slipping. > > OK — back in I go . . . > http://2.bp.blogspot.com/-t84cI65qdtE/TaxAHhoNrgI/AAAAAAAABdY/74WdK5ON_Rc/s1600/photo.JPG > > > All the best, > > Edd > > > Edd M. Schillay > Starship Enterprise > C&C 37+ | Sail No: NCC-1701-B > City Island, NY > Starship Enterprise's Captain's Log > > > > > > >> On Jul 17, 2017, at 9:53 AM, Della Barba, Joe via CnC-List >> <cnc-list@cnc-list.com> wrote: >> >> Note that many cell phone holsters have strong magnets to hold the case >> closed too. If you sit near where the fluxgate is……………… >> >> From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Russ & >> Melody via CnC-List >> Sent: Monday, July 17, 2017 1:16 AM >> To: cnc-list@cnc-list.com >> Cc: Russ & Melody <russ...@telus.net> >> Subject: Re: Stus-List Raymarine Autopilot Question >> >> >> Good to hear. >> >> Frienfriends don't let frienfriends mess with fluxgate compasses. >> >> Cheers, Russ >> Sweet 35 mk-1 >> >> >> At 09:30 PM 16/07/2017, you wrote: >> >> Make sure there is no metal near the flux compass. A frienfriend had this >> happen to him, found a spray can next to his flux compass. >> >> >> >> Sent from my T-Mobile 4G LTE Device >> Doug Mountjoy >> POYC >> Pegasus (for sale) >> Lf38 >> Significant Other >> LF 39 >> >> -------- Original message -------- >> From: Edd Schillay via CnC-List <cnc-list@cnc-list.com> >> Date: 7/16/17 10:58 (GMT-08:00) >> To: cnc-list@cnc-list.com >> Cc: Edd Schillay <e...@schillay.com> >> Subject: Stus-List Raymarine Autopilot Question >> >> Listers, >> >> Yesterday, on a dinner trip to Oyster Bay, our autopilot stated to >> malfunction after about an hour or so. >> >> It would be holding a course, then start veering to port, then to starboard, >> then much more to port, then much more to starboard . . and so on. >> Eventually, it would get so far off (over 90 degrees), a the autopilot would >> disengage. I shut it down and tried to restart it by cutting power to it for >> about a minute, then it would happen again after a minute or two. >> >> I tries setting the p70 to “performance†to keep the boat more tightly >> on course, but that had no effect. The display kept showing how far off we >> were (so I know the EV sensor core was working), but it wasn’t correcting >> course properly. >> >> I ended up turning it off completely, in fears of getting a DUI inquiry from >> all the S-turns. >> >> Any ideas? To clarify, I have a ACU-200 and a ST4000+ wheel pilot. And, up >> until yesterday, it was working flawlessly. >> >> >> All the best, >> >> Edd >> >> >> Edd M. Schillay >> Starship Enterprise >> C&C 37+ | Sail No: NCC-1701-B >> City Island, NY >> Starship Enterprise's Captain's Log >> _______________________________________________ >> >> This list is supported by the generous donations of our members. If you wish >> to make a contribution to offset our costs, please go to: >> https://www.paypal.me/stumurray >> >> All Contributions are greatly appreciated! >> _______________________________________________ >> >> This list is supported by the generous donations of our members. If you wish >> to make a contribution to offset our costs, please go to: >> https://www.paypal.me/stumurray >> >> All Contributions are greatly appreciated! > > _______________________________________________ > > This list is supported by the generous donations of our members. If you wish > to make a contribution to offset our costs, please go to: > https://www.paypal.me/stumurray > > All Contributions are greatly appreciated!
_______________________________________________ This list is supported by the generous donations of our members. If you wish to make a contribution to offset our costs, please go to: https://www.paypal.me/stumurray All Contributions are greatly appreciated!