My '73 30-1 is also without the tangs. No holes in mast either, so there're
not just missing.RonWild CheriSTL
From: Randy Stafford via CnC-List <cnc-list@cnc-list.com>
To: cnc-list <cnc-list@cnc-list.com>
Cc: randy.staff...@comcast.net
Sent: Tuesday, May 31, 2016 3:33 PM
Subject: Re: Stus-List mast collar tangs C& C 33-2
Interesting that apparently only some but not all C&C models have these mast
collar tangs. Mine (C&C 30 MK I hull #7, designed 1971-sh built 1972) does not
have them. It has a bulkhead about a half-foot forward of the mast that is
strongly tabbed to the cabin top, which is presumably the design element
intended to prevent upward flexing of the cabin top. I could see how tangs
fastened to mast and collar could do the same thing, using the mast as a
structural member. I wonder when and under what circumstances C&C chose to use
tangs vs. bulkheads.
Cheers,Randy StaffordS/V GrenadineC&C 30-1 #7Ken Caryl, CO
From: "jhnelson via CnC-List" <cnc-list@cnc-list.com>
To: "cnc-list" <cnc-list@cnc-list.com>
Cc: "jhnelson" <jhnelso...@gmail.com>
Sent: Tuesday, May 31, 2016 12:43:50 PM
Subject: Re: Stus-List mast collar tangs C& C 33-2
Cabin top flexes upward, doors won't close. Boat flexes more than it
should.Generally I don't think anything catestrophic would happen...immediately
anyway. But flexing the Cabin top is likely not great.
Sent from my Samsung device
-------- Original message --------
From: Wayne Anstey via CnC-List <cnc-list@cnc-list.com>
Date: 2016-05-31 3:25 PM (GMT-04:00)
To: Frederick G Street via CnC-List <cnc-list@cnc-list.com>
Cc: Wayne Anstey <wans...@ns.sympatico.ca>
Subject: Re: Stus-List mast collar tangs C& C 33-2
What happens if you don't put them on at all and only put the wedges in?
Wayne Anstey
Resilience
1964 C&C 30mk1
Bedford, N S, Canada
Sent from my Bell Sony device over Canada’s largest network.
---- Bruce Pope via CnC-List wrote ----
> Hi Doug.
>
>
> I had the same problem on my 29-2. Installed the mast for the first time
> after transport, tuned the rigging, everything set up and then... found the
> tangs in a galley drawer where I had stored them for transport. I had to
> slacken all rigging before I could get the holes to align.
>
>
>
>
> From: CnC-List <cnc-list-boun...@cnc-list.com> on behalf of Persuasion37 via
> CnC-List <cnc-list@cnc-list.com>
> Sent: Tuesday, May 31, 2016 4:17 AM
> To: cnc-list@cnc-list.com
> Cc: Persuasion37
> Subject: Re: Stus-List mast collar tangs C& C 33-2
>
> Hi Doug.
>
>
> On my 37 I cannot install the bolts if I tune the mast first. I've done this
> a couple of times now and the only thing to do is loosen everything, install
> the bolts and re-tune.
>
>
> Mike
>
> C&C 37
>
> Long Sault
>
>
> Sent from my iPad
>
>
> On May 30, 2016, at 8:05 PM, doug.welch--- via CnC-List
> <cnc-list@cnc-list.com> wrote:
>
> When I was rigging my new to me 33-2 we couldn't locate one of the the mast
> collar tangs so I had a friend fabricate a duplicate. Both are now misaligned
> and the holes are about 1/4 inch too high to slip the bolt in (the boat is
> fully rigged). My friends have different opinions on this. One says release
> the rigging and the tangs will slightly deform the cabin top when we reset
> the mast. Another days remake the tangs so the bolts line up with jokes in
> the mast when it's fully rigged. Looking for help from you folks.
>
>
>
> Cheers,
>
> Doug
>
> Sent from Yahoo Mail on Android
>
> _______________________________________________
>
> This list is supported by the generous donations of our members. If you like
> what we do, please help us pay for our costs by donating. All Contributions
> are greatly appreciated!
_______________________________________________
This list is supported by the generous donations of our members. If you like
what we do, please help us pay for our costs by donating. All Contributions are
greatly appreciated!
_______________________________________________
This list is supported by the generous donations of our members. If you like
what we do, please help us pay for our costs by donating. All Contributions are
greatly appreciated!
_______________________________________________
This list is supported by the generous donations of our members. If you like
what we do, please help us pay for our costs by donating. All Contributions are
greatly appreciated!
