Frank, I just installed a Lewmar V-2 vertical windlass on an Island Packet 37 on the bowsprit. Probably not similar to your installation but just wanted to say I was impressed with the design and quality of the Lewmar windlass.
Dennis C. Touche' 35-1 #83 Mandeville, LA On Thu, Apr 10, 2014 at 1:14 PM, Frank Woronkowicz <fworonkow...@gmail.com>wrote: > My boat has Yanmar 3QM30 with original added fresh water circ. jabsco pump > and Sunrod HEx. overheating on the Chesapeake Bay. I think to replace > engine and propeller. Please let me know if any LF owner already did this > work and what is approx cost. > The second question is windllas type and installation. Did anybody > install windlass in anchor compartment? > I have her for approx. 20 years and finally these should be done, > Thanks > Frank Woronkowicz > LF 38 s/y Gdynia > ANNAPOLIS MD > fworonkow...@gmail.com > > Sent from my iPhone > > On Apr 10, 2014, at 1:43 PM, "Bill Coleman" <colt...@verizon.net> wrote: > > I wish you had posted this a month ago! > > I just bought two different kinds of Lubriplate waterproof grease to > lather up my prop gears (which are exposed) > > So far none have survived the summer. > > > > This looks like it might stay. > > > > Bill Coleman > > C&C 39 <image001.gif> > > > > *From:* CnC-List > [mailto:cnc-list-boun...@cnc-list.com<cnc-list-boun...@cnc-list.com>] > *On Behalf Of *Jim Watts > *Sent:* Wednesday, April 09, 2014 10:28 PM > *To:* 1 CnC List > *Subject:* Re: Stus-List LF 38 rudder post grease fitting (again) > > > > If it's a bearing, it's plastic, probably Delrin (Acetal). Teflon grease > is wax-based, so safe on either. Star Brite has a tub of Teflon grease for > not too stupid a price. http://www.starbrite.com/item/white-ptef-lubricant > > > Jim Watts > Paradigm Shift > C&C 35 Mk III > Victoria, BC > > > > On 9 April 2014 09:29, Della Barba, Joe <joe.della.ba...@ssa.gov> wrote: > > On the 35 there is no bearing. It is just a metal shaft in a fiberglass > tube. > > > > *Joe Della Barba* > > Coquina > > *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of *Daniel > Sheer > *Sent:* Wednesday, April 09, 2014 12:13 PM > *To:* cnc-list@cnc-list.com > *Subject:* Stus-List LF 38 rudder post grease fitting (again) > > > > Anybody know whether the bearing is metal or plastic? Trying to figure out > what grease to use. > > > > Dan Sheer > > Pegathy LF38 > > Rock Creek off the Patapsco > > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com > > > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com > > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com > >
_______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
