Richard, If it is a plug you need to get it out and insert a Zerc fitting for the grease gun. Hit it with PB Blaster before you try to move it.
Joel On Wed, Apr 9, 2014 at 4:33 PM, Richard N. Bush <bushma...@aol.com> wrote: > Joel, I didn't realize that there might be different fittings; if its just > a plug I can pull it out and inject the grease down into the hole? > > Thanks > Richard > 1985 37 CB > > Richard N. Bush Law Offices > 2950 Breckenridge Lane, Suite Nine > Louisville, Kentucky 40220-1462 > 502-584-7255 > > > -----Original Message----- > From: Joel Aronson <joel.aron...@gmail.com> > To: cnc-list <cnc-list@cnc-list.com> > Sent: Wed, Apr 9, 2014 4:09 pm > Subject: Re: Stus-List LF38 rudder post grease fitting > > Richard, > > Is it a Zerc fitting or a plug? If the former I would take my chances > and spray with PB Blaster and then lube it with a lube gun. > > Joel > > > On Wed, Apr 9, 2014 at 3:54 PM, Richard N. Bush <bushma...@aol.com> wrote: > >> Fred, and others... I located the fitting on my boat and it appears to >> rusted..I'm almost afraid to touch it as it seems it might fall off, any >> thoughts on what I should do? Thanks >> >> Richard >> 1985 37 CB >> Richard N. Bush Law Offices >> 2950 Breckenridge Lane, Suite Nine >> Louisville, Kentucky 40220-1462 >> 502-584-7255 >> >> >> -----Original Message----- >> From: Frederick G Street <f...@postaudio.net> >> To: Daniel Sheer <dansh...@yahoo.com> >> Cc: cnc-list <cnc-list@cnc-list.com> >> Sent: Wed, Apr 9, 2014 12:27 pm >> Subject: Re: Stus-List LF38 rudder post grease fitting >> >> I just use a good waterproof grease like Lubriplate. Seems to work >> just fine. >> >> And probably a good idea to keep these discussion "on-list" so others >> can chime in, as well. I'm CC'ing the list. >> >> -- Fred >> >> Fred Street -- Minneapolis >> S/V Oceanis (1979 C&C Landfall 38) -- on the hard in Bayfield, WI :^( >> >> On Apr 9, 2014, at 11:11 AM, Daniel Sheer <dansh...@yahoo.com> wrote: >> >> Fred, >> >> Do you know if the bushing is metal or plastic? Trying to figure out what >> kind of grease to use. >> >> Thanks >> >> Dan >> >> On Tuesday, April 8, 2014 9:39 PM, Daniel Sheer <dansh...@yahoo.com> >> wrote: >> Thanks Fred. >> On Tuesday, April 8, 2014 10:36 AM, Frederick G Street < >> f...@postaudio.net> wrote: >> Mine (hull #009, 1979) has a zerc fitting more or less on the starboard >> side and aft; difficult to see, and harder to reach. >> >> Fred Street -- Minneapolis >> S/V Oceanis (1979 C&C Landfall 38) -- on the hard in Bayfield, WI :^( >> >> On Apr 7, 2014, at 8:38 PM, Daniel Sheer <dansh...@yahoo.com> wrote: >> >> Anybody know if the LF38 has a grease fitting on the rudder post, and >> if so, where it is? >> >> Dan Sheer >> Pegathy LF38 >> Rock Creek off the Patapsco >> >> >> >> >> >> >> _______________________________________________ >> This List is provided by the C&C Photo >> Albumhttp://www.cncphotoalbum.comcnc-l...@cnc-list.com >> >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> http://www.cncphotoalbum.com >> CnC-List@cnc-list.com >> >> > > > -- > Joel > 301 541 8551 > > _______________________________________________ > This List is provided by the C&C Photo > Albumhttp://www.cncphotoalbum.comcnc-l...@cnc-list.com > > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com > > -- Joel 301 541 8551
_______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
