Here's ours...simple enough to cut the top rail and put in a gate. Remember to leave the ladder on the outside of the gate so you can pull it down from the water. Both our C&C's came from the PO with the gate wire threaded through the ladder, for some inscrutable reason.
https://lh6.googleusercontent.com/-UXUqb120Ihw/Uh9uoRAymRI/AAAAAAAABTs/4SocqvNPCic/w1270-h857-no/storm+riding.jpg Jim Watts Paradigm Shift C&C 35 Mk III Victoria, BC On 6 February 2014 10:48, Dennis Cheuvront <capt...@gmail.com> wrote: > That's what I was describing in my earlier reply. Easy to do. Ends caps > with eyes are relatively inexpensive. Just cut the rail leaving a little > stub, insert end cap with eye and make the lifeline gate. Done. > > If you don't have a lower rail and are worried about strength of the > pulpit, you can install one with a couple of rail tees on the vertical > pulpit section and a short section of rail. Would provide a lower rail to > step over. > > Now that I visualize this, I might actually do this on Touche'. > > Dennis C. > Touche' 35-1 #83 > Mandeville, LA > > > On Thu, Feb 6, 2014 at 12:19 PM, Prime Interest > <primeinter...@gmail.com>wrote: > >> Take a look at >> >> >> >> http://www.barkers-island-marina.com/yachtworld/sail.htm >> >> >> >> the $19,900 C&C 32 .. photo #2 >> >> >> >> >> >> >> >> >> >> ed >> >> >> >> Prime Interest >> >> 1982 C&C Landfall >> >> Toronto, Canada >> >> >> >> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of *John >> Russo >> *Sent:* Thursday, February 06, 2014 12:52 PM >> *To:* cnc-list@cnc-list.com >> *Subject:* Re: Stus-List [SPAM] Climing over the stern rail is a pain >> >> >> >> Thanks Bob, that would be helpful. >> >> >> >> John >> >> >> >> johnrussob...@optonline.net >> >> >> >> *From:* CnC-List >> [mailto:cnc-list-boun...@cnc-list.com<cnc-list-boun...@cnc-list.com>] >> *On Behalf Of *Robert Abbott >> *Sent:* Thursday, February 06, 2014 12:39 PM >> *To:* cnc-list@cnc-list.com >> *Subject:* [SPAM]Stus-List Climing over the stern rail is a pain >> >> >> >> John >> >> Our 32 has a lower rail and a gate up top.....looks to be factory but not >> sure....can send you a pic offline if you want. >> >> Rob Abbott >> AZURA >> C&C 32 - 84 >> Halifax, N.S. >> >> >> >> >> On 2014/02/05 3:33 PM, John Russo wrote: >> >> >> >> I have a 32 with a double rail at the stern and am thinking about cutting >> the upper and adding a gate. My swim ladder actually comes slightly above >> the lower rail when up where it tie it. My concern is that I have a motor >> mount and a 65 Lb outboard on the stern rail port side vertical post which >> I will have to shift more to port but wondered about the rail strength >> after cutting. Any thoughts? I am also looking for a lighter outboard >> with a little less HP. >> >> >> >> John >> >> Arpeggio 32 >> >> Norwalk CT >> >> >> >> >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> http://www.cncphotoalbum.com >> CnC-List@cnc-list.com >> >> > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com > >
_______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
