Not yet, Dwight, but there will be some. I'll also share some from the prior (more extensive) core work I had done a couple of years ago. Any idea how I can effectively share with this list...? They're not great quality photos (taken with a phone by the yard), but they tell the story.
As to preventive measures - get a very bright flashlight and an inspection mirror and carefully examine the bilge area - any water seepage, tabbing that looks suspect should be considered. Unfortunately any further examination may need to be destructive. Tim On Fri, Jan 11, 2013 at 9:13 AM, dwight veinot <dwightvei...@hfx.eastlink.ca > wrote: > ** ** ** > > Tim**** > > ** ** > > Do you have any photos of the repair that you can share? If so I’d like > to have a look, please**** > > ** ** > > Dwight Veinot**** > > C&C 35 MKII, Alianna**** > > Head of St. Margaret's Bay, NS**** > ------------------------------ > > *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of *Tim > Goodyear > *Sent:* January 11, 2013 9:59 AM > *To:* Dennis C.; cnc-list@cnc-list.com > > *Subject:* Re: Stus-List Keel stub cracks > **** > > ** ** > > The cause of the cracks was wet core just outboard / above the solid glass > at the turn of the bilge (right by the mast step). There was a void > between the mast step assembly (glass) and the hull proper that allowed > water to sit for a while (29 years?) against the inner laminate... I now > have full confidence in the hull integrity (having replaced most of it over > the last two years), but am many dollars lighter. The temptation of a new > boat is growing.**** > > ** ** > > Tim**** > > Mojito**** > > 1984 C&C 35-3**** > > ****Branford**, **CT******** > > ** ** > > On Sun, Dec 16, 2012 at 8:50 PM, Dennis C. <capt...@yahoo.com> wrote:**** > > Tim, > > My boat is a lot older than yours but if it's any indication, their layup > schedules weren't very good. I've re-tabbed most of the bulkhead/hull > joints in Touche's forward section. A few were detached or broken but most > were just bad practice. > > When I had the boat hauled about 5 years ago for a barrier coat, I could > see cosmetic cracks in the matte once the gelcoat was removed from the > underbody. These cracks aligned with the bulkheads. The bulkhead tabs had > no fillets. They were all 90 degree joints. This created stress points at > the joints which manifested themselves as the cosmetic cracks on the > outside of the hull. > > I have been re-tabbing all the bulkheads with filleted joints. I ground > out the old tabbing, created fillets and re-tabbed with 4 inch biaxial > tape. To create the fillets, I put thickened epoxy in the joint and > smoothed it with the back of a plastic spoon. This creates a nice radius > for the fillet. The filleted joints spread the load. This is particularly > important in the forward section of the boat as that's where the boat > pounds into waves. > > Dennis C. > Touche' 35-1 #83 > ****Mandeville**, **LA******** > > ** ** > > ** ** > ------------------------------ > > *From:* Tim Goodyear <timg...@gmail.com> > *To:* "cnc-list@cnc-list.com" <cnc-list@cnc-list.com> > *Sent:* Sunday, December 16, 2012 4:29 PM > *Subject:* Re: Stus-List Keel stub cracks**** > > ** ** > > There is some tabbing in the bilge sump between floors and hull that has > become detached. I'll have that ground off and reattached and will add > glass on the outside and fair. Does anyone have access to any of the > original layup schedules in that area? I have copies of all the drawings > that were available, but none were that specific on construction methods.* > *** > > ** ** > > Thanks,**** > > ** ** > > Tim**** > > Mojito**** > > C&C 35-3 1984**** > > ****Branford**, **CT******** > > ** ** > > On Sun, Dec 2, 2012 at 7:34 PM, Graham Collins <cnclistforw...@hotmail.com> > wrote:**** > > Hi Tim > I'd pull the cabin sole and see if the floor grid is still well attached > to the hull at the turn of the bilge, I'm guessing on the port side it is > not. > > Graham Collins > Secret Plans > C&C 35-III #11 > > > Tim Goodyear wrote:**** > > Hello all 35-3 owners - I'm looking for some advice, especially from those > who have re-habbed their keels on this model... > I was checking on Mojito this morning, and noticed beads of moisture in > two areas; a spot at the top of the keel trailing edge and an 8" hairline > crack on the port side at hull / keel stub (almost exactly where the mast > step is internally). Would this have been enough for you to go ahead with > major keel surgery? > Rear of keel > I've been trying to resolve this for a while; two separate boat yards have > had a go at if, and the area is now solid fiberglass / epoxy, but still a > tiny crack / area of moisture. There was water in the bilge just aft of the > rear keel bolt (I removed the floorboards and sponged the area dry). Water > would not normally stay in that area, but the boat is tilted back a little > on the stands. I have not had the keel bolts torqued in 7 years (since I > bought Mojito). > Mast Step area > This is the first year I've noticed moisture in that area; there have been > hairline cracks in the antifouling before. The mast is stepped and I can't > access that area through the mast step, which appears sound. > Thanks, > Tim > Mojito > 1984 C&C 35-3 > ****Branford**, **CT**** > > **** > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com**** > > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com**** > > ** ** > > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com > > **** > > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com**** > > ** ** > ------------------------------ > > No virus found in this message. > Checked by AVG - www.avg.com > Version: 2012.0.2221 / Virus Database: 2637/5525 - Release Date: 01/11/13* > *** > > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com > >
_______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
