It is "service unsupported-transceiver" it is hidden so tab completion won't help you.
cat3560-1(config)#service unsupported-transceiver Warning: When Cisco determines that a fault or defect can be traced to the use of third-party transceivers installed by a customer or reseller, then, at Cisco's discretion, Cisco may withhold support under warranty or a Cisco support program. In the course of providing support for a Cisco networking product Cisco may require that the end user install Cisco transceivers if Cisco determines that removing third-party parts will assist Cisco in diagnosing the cause of a support issue. cat3560-1(config)#no service unsupported-transceiver David -- http://dcp.dcptech.com > -----Original Message----- > From: [email protected] [mailto:cisco-nsp- > [email protected]] On Behalf Of Dennis > Sent: Monday, May 23, 2011 4:15 PM > To: [email protected] > Subject: [c-nsp] Fwd: GBIC_SECURITY_CRYPT-4-ID_MISMATCH: Identification > check failed for GBIC in port [dec] > > I'm out of my element at this point - does anyone else have any > suggestions? > > > ---------- Forwarded message ---------- > From: Farooq Razzaque <[email protected]> > Date: Mon, May 23, 2011 at 1:05 PM > Subject: RE: [c-nsp] GBIC_SECURITY_CRYPT-4-ID_MISMATCH: Identification > check failed for GBIC in port [dec] > To: [email protected] > > > Dear Dennis > > I tried the following command but this command is not support. can u > please check again and let me know > > service-unsupported transceiver > > > > > > > > > > > > Date: Mon, 23 May 2011 09:31:58 -0700 > > Subject: Re: [c-nsp] GBIC_SECURITY_CRYPT-4-ID_MISMATCH: > Identification check failed for GBIC in port [dec] > > From: [email protected] > > To: [email protected] > > > > On Mon, May 23, 2011 at 9:30 AM, Farooq Razzaque > <[email protected]> wrote: > > > Dear Dennis > > > > > > Is there need to upgrade the IOS ? > > > > I don't know for sure. Are you using Cisco SFPs? What IOS is it? > > > > > > > > > > service-unsupported transceiver > > > > > > Do i need to put the following commands as well or only the above > command > > > will be sufficient. > > > > Just try the above if that doesn't work put in the below commands as > well. > > > > > > > > no errdisable detect cause gbic-invalid > > > errdisable recovery cause all > > > errdisable recovery interval 30 > > > > > > > Thanks, > > > > Dennis O. > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >> Date: Mon, 23 May 2011 09:27:51 -0700 > > >> Subject: Re: [c-nsp] GBIC_SECURITY_CRYPT-4-ID_MISMATCH: > Identification > > >> check failed for GBIC in port [dec] > > >> From: [email protected] > > >> To: [email protected] > > >> > > >> On Mon, May 23, 2011 at 9:26 AM, Farooq Razzaque > <[email protected]> > > >> wrote: > > >> > Dear Dannis > > >> > > > >> > Thanks for your reply > > >> > > > >> > Is there any need to upgrade the IOS ? > > >> > > > >> > Are the following commands will be put on the GBIC interface > > >> > > >> Just do it in global config mode. > > > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
