Hi Irwin, I just tried on IspyB and I was able to reprocess data collected on a September visit, thus you should be fine if your session was only 30/40 days ago.
I have never tried ccp4i2 on windows, sorry I cannot comment on this (but xia2-dials works fine in Linux/Mac using the master.h5 file). As Marco suggested if you use xia2-xds make sure you have the correct plug-in for Eiger detector (https://www.diamond.ac.uk/Instruments/Mx/Common/Common-Manual/Eiger2-Detectors.html) BW, D > On 22 Dec 2020, at 20:55, Irwin Selvam > <irwin.sel...@postgrad.manchester.ac.uk> wrote: > > > Hi, > > Unfortunately, the data were collected more than 30/40 days ago so I > requested them via TOPCAT - unless there is a way round this? > > All the best, > > Irwin > From: Dom Bellini <dbell...@mrc-lmb.cam.ac.uk> > Sent: 22 December 2020 18:54 > To: Irwin Selvam <irwin.sel...@postgrad.manchester.ac.uk>; > CCP4BB@JISCMAIL.AC.UK <CCP4BB@JISCMAIL.AC.UK> > Subject: Re: [ccp4bb] Reprocessing images collected on an Eiger2 detector > using Xia2Dials on CCP4i2's GUI > > Hi Irwin, > > You should use the master.h5 file, I am not sure why that is not working. > However, if you collected at Diamond, it is also possible to reprocess your > data directly from IspyB, which is very easy and convenient if you just want > to reprocess with different resolution > https://www.diamond.ac.uk/Instruments/Mx/Common/Common-Manual/Data-Analysis/Reprocessing-in-ISPyB.html > > BW, > > D > >> On 22/12/2020 16:53, Irwin Selvam wrote: >> Hi, >> >> I'd like to reprocess some data that were collected on an Eiger2 detector at >> Diamond with Xia2Dials using CCP4i2's GUI. I'm running CCP4i2 on a 64-bit >> Windows 10 machine. The data were processed successfully at Diamond with no >> obvious pathologies, the high resolution limit was just a little generous. >> The folder in question contains a Diamond specific file (.nsx extension), >> two image files (.h5), a header (.cbf), a master (.h5) and meta file (.h5). >> I've tried pointing Xia2 to the folder itself (which works when processing >> data collected on PILATUS detectors) and each of the files contained therein >> (except the Diamond specific file). Each time this results in the error " >> -ERROR- None:56 Error in wrapper xia2_dials 0.0:: External process exited >> with exit code != 0 Process: C:\CCP4-7\7.1\bin\xia2.bat -ERROR- None:47 >> Error in wrapper xia2_dials 0.0:: Error in checking external process after >> completion exit status and code: 0 1". I've attached the error, debug etc >> files for a representative 'run' to this email. Which files do I need to >> point xia2 towards to get it to run? Any help would be appreciated. >> >> All the best, >> >> Irwin >> >> To unsubscribe from the CCP4BB list, click the following link: >> https://www.jiscmail.ac.uk/cgi-bin/WA-JISC.exe?SUBED1=CCP4BB&A=1 >> > > -- > Dom Bellini, Xray Crystallography Facility (1S205) > MRC Laboratory of Molecular Biology > Francis Crick Avenue > Cambridge Biomedical Campus > Cambridge CB2 0QH > Phone 01223 267839 > > To unsubscribe from the CCP4BB list, click the following link: > https://www.jiscmail.ac.uk/cgi-bin/WA-JISC.exe?SUBED1=CCP4BB&A=1 ######################################################################## To unsubscribe from the CCP4BB list, click the following link: https://www.jiscmail.ac.uk/cgi-bin/WA-JISC.exe?SUBED1=CCP4BB&A=1 This message was issued to members of www.jiscmail.ac.uk/CCP4BB, a mailing list hosted by www.jiscmail.ac.uk, terms & conditions are available at https://www.jiscmail.ac.uk/policyandsecurity/
