Hey Shai,
Remove the "default" keyword and just type in "auto-cost reference-bandwidth 1000". Whilst the CLI seems to accept your command, it doesn't do anything. Cheers, Jared Scrivener CCIE3 #16983 (R&S, Security, SP), CISSP Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.810.454.0130 Mailto: <mailto:[email protected]> [email protected] From: [email protected] [mailto:[email protected]] On Behalf Of Shai Loufton Sent: Sunday, 1 February 2009 5:12 AM To: [email protected] Subject: [OSL | CCIE_SP] Weird thing under R6 of the SP Pod (not 7200/ATM) I am currently running some technology labs on the SP POD and it seems that the IOS used on R6 does not support (no error - some kind of IOS glitch) this command under the ospf process - "default auto-cost reference-bandwidth bandwidth" a few examples - R6(config-router)#default auto-cost reference-bandwidth 1000 R6(config-router)#do sh run | b router ospf router ospf 1 log-adjacency-changes area 69 virtual-link 200.0.0.9 network 150.50.69.6 0.0.0.0 area 69 network 150.50.100.6 0.0.0.0 area 0 network 200.0.0.6 0.0.0.0 area 0 ! ip forward-protocol nd no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! ! control-plane ! ! R6(config-router)#default auto-cost reference-bandwidth 10000 R6(config-router)#do sh run | b router ospf router ospf 1 log-adjacency-changes area 69 virtual-link 200.0.0.9 network 150.50.69.6 0.0.0.0 area 69 network 150.50.100.6 0.0.0.0 area 0 network 200.0.0.6 0.0.0.0 area 0 ! ip forward-protocol nd no ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! ! control-plane ! ! R6(config-router)#do sh ip ospf int f0/0 FastEthernet0/0 is up, line protocol is up Internet Address 150.50.7.6/25, Area 69 Process ID 1, Router ID 200.0.0.6, Network Type BROADCAST, Cost: 1 Enabled by interface config, including secondary ip addresses Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) 200.0.0.6, Interface address 150.50.7.6 No backup designated router on this network Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 oob-resync timeout 40 Hello due in 00:00:02 Supports Link-local Signaling (LLS) Cisco NSF helper support enabled IETF NSF helper support enabled Index 2/4, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 0, maximum is 0 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 0, Adjacent neighbor count is 0 Suppress hello for 0 neighbor(s) R6(config-router)# R6#sh ver Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(22)T, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Fri 10-Oct-08 00:05 by prod_rel_team ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1) R6 uptime is 2 hours, 31 minutes System returned to ROM by reload at 07:33:32 UTC Sun Feb 1 2009 System image file is "flash:c2800nm-adventerprisek9-mz.124-22.T.bin" Anyone else noticed this? It seems you can issue the command - but it does nothing. I think it's the IOS - but maybe I am missing something Any thoughts anyone? Shai l.
