hm....I am a bit confused here. 150 sec, milisec? different commands
inject different values. if we need to see 150 from show ip eigrp
topology prefix then below should be valid solution?
route-map LOEIGRP permit 10
match interface Loopback0
set metric 0 15 255 1 1500
IP-EIGRP (AS 467): Topology entry for 135.211.4.4/32
State is Passive, Query origin flag is 1, 1 Successor(s), FD is 3840
Routing Descriptor Blocks:
0.0.0.0, from Rconnected, Send flag is 0x0
Composite metric is (3840/0), Route is External
Vector metric:
Minimum bandwidth is 0 Kbit
Total delay is 150 microseconds
Reliability is 255/255
Load is 1/255
Minimum MTU is 1500
Hop count is 0
External data:
Originating router is 135.211.4.4 (this system)
AS number of route is 0
External protocol is Connected, external metric is 0
Administrator tag is 0 (0x00000000)
If this is correct then there is typo in DSG.
Lukasz
On 2012-11-06 16:07, Marko Milivojevic wrote:
But the task requires delay of 150.
--
Marko Milivojevic - CCIE #18427 (SP R&S)
Senior CCIE Instructor - IPexpert
:: This message was sent from a mobile device. I apologize for errors
and brevity. ::
On Nov 6, 2012, at 8:05, Lukasz <[email protected]> wrote:
with solution from DSG
route-map LOEIGRP permit 10
match interface Loopback0
set metric 0 150 255 1 1500
R4#show ip eigrp topology 135.211.4.4/32
IP-EIGRP (AS 467): Topology entry for 135.211.4.4/32
State is Passive, Query origin flag is 1, 1 Successor(s), FD is
38400
Routing Descriptor Blocks:
0.0.0.0, from Rconnected, Send flag is 0x0
Composite metric is (38400/0), Route is External
Vector metric:
Minimum bandwidth is 0 Kbit
Total delay is 1500 microseconds
Reliability is 255/255
Load is 1/255
Minimum MTU is 1500
Hop count is 0
which I think is incorrect.
you are right I should delete one zero as metric takes tens of
microseconds not microseconds, so my valid solution should be:
redistribute connected metric 1 15000000 255 1 1500 route-map
LOEIGRP
State is Passive, Query origin flag is 1, 1 Successor(s), FD is
3840000000
Routing Descriptor Blocks:
0.0.0.0, from Rconnected, Send flag is 0x0
Composite metric is (3840000000/0), Route is External
Vector metric:
Minimum bandwidth is 1 Kbit
Total delay is 150000000 microseconds
Reliability is 255/255
Load is 1/255
Minimum MTU is 1500
Hop count is 0
Lukasz
On 2012-11-06 15:38, Marko Milivojevic wrote:
I think there's one or two zeroes extra.
Run "sh ip eigrp topology" for that prefix and see the delay. If
it's
150, it doesn't matter what syntax you used.
--
Marko Milivojevic - CCIE #18427 (SP R&S)
Senior CCIE Instructor - IPexpert
:: This message was sent from a mobile device. I apologize for
errors
and brevity. ::
On Nov 6, 2012, at 7:22, Lukasz <[email protected]> wrote:
Hi All,
In the above section of the lab it says that R4 loopback should be
redistributed into the eigrp process with delay 150. An example from
DSG shows route-map with seting metric 0 150 255 1 1500.
As we use metric weights 0 0 0 1 0 0 we will only take delay into
account when calculating metric.
My question...is below solution valid as well?
route-map LOEIGRP permit 10
match interfce lo0
!
router eigrp 467
redistribute connected metric 1 150000000 1 1 1 route-map LOEIGRP
Thanks,
Lukasz
_______________________________________________
For more information regarding industry leading CCIE Lab training,
please visit www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
http://onlinestudylist.com/mailman/listinfo/ccie_rs
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
http://onlinestudylist.com/mailman/listinfo/ccie_rs
