But the task requires delay of 150. -- Marko Milivojevic - CCIE #18427 (SP R&S) Senior CCIE Instructor - IPexpert
:: This message was sent from a mobile device. I apologize for errors and brevity. :: On Nov 6, 2012, at 8:05, Lukasz <[email protected]> wrote: > with solution from DSG > > route-map LOEIGRP permit 10 > match interface Loopback0 > set metric 0 150 255 1 1500 > > > R4#show ip eigrp topology 135.211.4.4/32 > IP-EIGRP (AS 467): Topology entry for 135.211.4.4/32 > State is Passive, Query origin flag is 1, 1 Successor(s), FD is 38400 > Routing Descriptor Blocks: > 0.0.0.0, from Rconnected, Send flag is 0x0 > Composite metric is (38400/0), Route is External > Vector metric: > Minimum bandwidth is 0 Kbit > Total delay is 1500 microseconds > Reliability is 255/255 > Load is 1/255 > Minimum MTU is 1500 > Hop count is 0 > > which I think is incorrect. > > > you are right I should delete one zero as metric takes tens of microseconds > not microseconds, so my valid solution should be: > > > redistribute connected metric 1 15000000 255 1 1500 route-map LOEIGRP > > State is Passive, Query origin flag is 1, 1 Successor(s), FD is 3840000000 > Routing Descriptor Blocks: > 0.0.0.0, from Rconnected, Send flag is 0x0 > Composite metric is (3840000000/0), Route is External > Vector metric: > Minimum bandwidth is 1 Kbit > Total delay is 150000000 microseconds > Reliability is 255/255 > Load is 1/255 > Minimum MTU is 1500 > Hop count is 0 > > > Lukasz > > On 2012-11-06 15:38, Marko Milivojevic wrote: >> I think there's one or two zeroes extra. >> >> Run "sh ip eigrp topology" for that prefix and see the delay. If it's >> 150, it doesn't matter what syntax you used. >> >> -- >> Marko Milivojevic - CCIE #18427 (SP R&S) >> Senior CCIE Instructor - IPexpert >> >> :: This message was sent from a mobile device. I apologize for errors >> and brevity. :: >> >> On Nov 6, 2012, at 7:22, Lukasz <[email protected]> wrote: >> >>> Hi All, >>> >>> >>> In the above section of the lab it says that R4 loopback should be >>> redistributed into the eigrp process with delay 150. An example from DSG >>> shows route-map with seting metric 0 150 255 1 1500. >>> As we use metric weights 0 0 0 1 0 0 we will only take delay into account >>> when calculating metric. >>> >>> My question...is below solution valid as well? >>> >>> route-map LOEIGRP permit 10 >>> match interfce lo0 >>> ! >>> router eigrp 467 >>> redistribute connected metric 1 150000000 1 1 1 route-map LOEIGRP >>> >>> >>> >>> >>> Thanks, >>> Lukasz >>> _______________________________________________ >>> For more information regarding industry leading CCIE Lab training, please >>> visit www.ipexpert.com >>> >>> Are you a CCNP or CCIE and looking for a job? Check out >>> www.PlatinumPlacement.com >>> >>> http://onlinestudylist.com/mailman/listinfo/ccie_rs _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
