On Friday, 14 December 2007 14:09:27 +0000, Allan Black wrote: > I use an HP SureStore 718, which is very similar to the L280 (2 internal > slots and exactly the same 6-slot cartridge with the hinged handle). If > you like, I could post the relevant bits of my Bacula configuration, and > you could use that as a starting point.
Sure! I think that it can be very useful to me. > >> 3912 Failed to label Volume: ERR=dev.c:678 Rewind error on "Drive-1" > >> (/dev/nst0). ERR=Error de entrada/salida. > One other thought: the L280 is a High Voltage Differential (HVD) device. > If you connect it to a Low Voltage SCSI card, it will not work properly > and it may damage the SCSI card. Check you are using an HVD SCSI card. > (However I suspect you are, and furthermore I suspect that is why you > are using a SPARC machine - supported SBUS diff cards are easier to > come by than the PCI ones :-) Since this SCSI card was on SUN Ultra5 machine and the tape library was connected to it, I suspect the SCSI card is HVD card too ;-) sym3: <875> rev 0x14 at pci 0001:00:05.1 irq 16 sym3: No NVRAM, ID 7, Fast-20, SE, parity checking sym3: SCSI BUS has been reset. scsi3 : sym-2.2.3 Vendor: HP Model: C6280-7000 Rev: 2.10 Type: Medium Changer ANSI SCSI revision: 02 target3:0:1: Beginning Domain Validation target3:0:1: asynchronous target3:0:1: Ending Domain Validation Vendor: QUANTUM Model: DLT7000 Rev: 296D Type: Sequential-Access ANSI SCSI revision: 02 target3:0:2: Beginning Domain Validation target3:0:2: asynchronous target3:0:2: wide asynchronous target3:0:2: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 15) target3:0:2: Domain Validation skipping write tests target3:0:2: Ending Domain Validation 0001:00:05.1 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 14) Subsystem: LSI Logic / Symbios Logic LSI53C876/E PCI to Dual Channel SCSI Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 136 (4250ns min, 16000ns max), Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 16 Region 0: I/O ports at 1fe02011000 [size=256] Region 1: Memory at 1ff8001c000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at 1ff8001e000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at 1ff80030000 [disabled] [size=64K] Thanks for your response, Allan. Regards, Daniel -- Daniel Bareiro - System Administrator Fingerprint: BFB3 08D6 B4D1 31B2 72B9 29CE 6696 BF1B 14E6 1D37 Powered by Debian GNU/Linux Etch - Linux user #188.598
signature.asc
Description: Digital signature
------------------------------------------------------------------------- SF.Net email is sponsored by: Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace
_______________________________________________ Bacula-users mailing list Bacula-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bacula-users
