On Oct 21 18:28:16, h...@stare.cz wrote:
> On Oct 21 12:40:37, mark.kette...@xs4all.nl wrote:
> > > Date: Thu, 21 Oct 2021 11:54:36 +0200
> > > From: Jan Stary <h...@stare.cz>
> > >
> > > This is Raspberry 4 Model B, trying to install current/arm64
> > > from a miniroot dd'd to a uSD card.
> > >
> > > U-Boot boots fine, gets to boot>
> > > where I 'set tty fb0' as per INSTALL.arm64
> > > which make the console output go to the monitor
> > > (the micro HDMI to a HDMI in a monitor).
> > >
> > > The I boot bsd.rd, which goes well until it gets to the
> > > (I)nstall (U)pgrade (A)utoinsytall (S)hell?
> > > line: now no keypress does anything. This is the
> > > same keyboard on which I typed 'set tty fb0' seconds ago.
> > >
> > > Yes, I tried with many keyboards.
> > > Am I missing something obvious?
> >
> > I fear the U-Boot that shipped with the 7.0 release is broken. I
> > "fixed" -current such that the kernel doesn't panic, but it means
> > xhci(4) no longer attaches.
> > I don't think we have a fixed u-boot yet. So for now it would be best
> > to put the u-boot from 6.9 onto your SD card.
>
> Thanks, that works.
Is the fix specific to the RPI4?
Or does the Oct 23 snapshot contain a better fix?
I just installed a current snapshot on a RPI3,
without the need to replace the u-boot.
Jan
>
>
> OpenBSD 7.0-current (GENERIC.MP) #1360: Thu Oct 21 01:36:50 MDT 2021
> dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC.MP
> real mem = 8419930112 (8029MB)
> avail mem = 8128761856 (7752MB)
> random: good seed from bootblocks
> mainbus0 at root: Raspberry Pi 4 Model B Rev 1.4
> cpu0 at mainbus0 mpidr 0: ARM Cortex-A72 r0p3
> cpu0: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu0: 1024KB 64b/line 16-way L2 cache
> cpu0: CRC32,ASID16
> cpu1 at mainbus0 mpidr 1: ARM Cortex-A72 r0p3
> cpu1: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu1: 1024KB 64b/line 16-way L2 cache
> cpu1: CRC32,ASID16
> cpu2 at mainbus0 mpidr 2: ARM Cortex-A72 r0p3
> cpu2: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu2: 1024KB 64b/line 16-way L2 cache
> cpu2: CRC32,ASID16
> cpu3 at mainbus0 mpidr 3: ARM Cortex-A72 r0p3
> cpu3: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu3: 1024KB 64b/line 16-way L2 cache
> cpu3: CRC32,ASID16
> efi0 at mainbus0: UEFI 2.8
> efi0: Das U-Boot rev 0x20211000
> apm0 at mainbus0
> simplefb0 at mainbus0: 1824x984, 32bpp
> wsdisplay0 at simplefb0 mux 1: console (std, vt100 emulation)
> wsdisplay0: screen 1-5 added (std, vt100 emulation)
> "system" at mainbus0 not configured
> "axi" at mainbus0 not configured
> simplebus0 at mainbus0: "soc"
> bcmclock0 at simplebus0
> bcmmbox0 at simplebus0
> bcmgpio0 at simplebus0
> bcmaux0 at simplebus0
> ampintc0 at simplebus0 nirq 256, ncpu 4 ipi: 0, 1: "interrupt-controller"
> bcmtmon0 at simplebus0
> bcmdmac0 at simplebus0: DMA0 DMA2 DMA4 DMA5 DMA6 DMA7 DMA8 DMA9
> "timer" at simplebus0 not configured
> pluart0 at simplebus0
> "local_intc" at simplebus0 not configured
> bcmdog0 at simplebus0
> bcmirng0 at simplebus0
> "firmware" at simplebus0 not configured
> "power" at simplebus0 not configured
> "mailbox" at simplebus0 not configured
> sdhc0 at simplebus0
> sdhc0: SDHC 3.0, 250 MHz base clock
> sdmmc0 at sdhc0: 4-bit, sd high-speed, mmc high-speed
> "gpiomem" at simplebus0 not configured
> "fb" at simplebus0 not configured
> "vcsm" at simplebus0 not configured
> "clocks" at mainbus0 not configured
> "phy" at mainbus0 not configured
> "clk-27M" at mainbus0 not configured
> "clk-108M" at mainbus0 not configured
> simplebus1 at mainbus0: "emmc2bus"
> sdhc1 at simplebus1
> sdhc1: SDHC 3.0, 100 MHz base clock
> sdmmc1 at sdhc1: 8-bit, sd high-speed, mmc high-speed, ddr52, dma
> "arm-pmu" at mainbus0 not configured
> agtimer0 at mainbus0: 54000 kHz
> simplebus2 at mainbus0: "scb"
> bcmpcie0 at simplebus2: disabled
> bse0 at simplebus2: address dc:a6:32:e0:50:d3
> brgphy0 at bse0 phy 1: BCM54210E 10/100/1000baseT PHY, rev. 2
> "dma" at simplebus2 not configured
> "hevc-decoder" at simplebus2 not configured
> "rpivid-local-intc" at simplebus2 not configured
> "h264-decoder" at simplebus2 not configured
> "vp9-decoder" at simplebus2 not configured
> gpioleds0 at mainbus0: no LEDs
> "sd_io_1v8_reg" at mainbus0 not configured
> "sd_vcc_reg" at mainbus0 not configured
> "fixedregulator_3v3" at mainbus0 not configured
> "fixedregulator_5v0" at mainbus0 not configured
> simplebus3 at mainbus0: "v3dbus"
> "bootloader" at mainbus0 not configured
> dt: 445 probes
> scsibus0 at sdmmc1: 2 targets, initiator 0
> sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SD16G, 0030> removable
> sd0: 14804MB, 512 bytes/sector, 30318592 sectors
> bwfm0 at sdmmc0 function 1
> manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 2 not configured
> manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 3 not configured
> vscsi0 at root
> scsibus1 at vscsi0: 256 targets
> softraid0 at root
> scsibus2 at softraid0: 256 targets
> root on sd0a (45389c1cc48ccfc4.a) swap on sd0b dump on sd0b
> WARNING: CHECK AND RESET THE DATE!
> gpio0 at bcmgpio0: 58 pins
> bwfm0: failed loadfirmware of file
> brcmfmac43455-sdio.raspberrypi,4-model-b.bin
>
>
