Hi,
Thanks for the OpenBSD developers, now I can run 6.7 on my Rock64 v2.
However,
there's no cpu dynamic frequency adjust it seems.
sysctl hw output:
hw.machine=arm64
hw.model=ARM Cortex-A53 r0p4
hw.ncpu=4
hw.byteorder=1234
hw.pagesize=4096
hw.disknames=sd0:682a6643f5752b65
hw.diskcount=1
hw.product=Pine64 Rock64
hw.serialno=d12da74ba2971686
hw.physmem=1006903296
hw.usermem=1006891008
hw.ncpufound=4
hw.allowpowerdown=1
hw.ncpuonline=4
It's not the same as r2s that I've been testing, which has the same cpu as
Rock64
and DO have perfpolicy.
The dmesg is as follows:
OpenBSD 6.7 (GENERIC.MP) #1: Sat May 16 15:59:24 MDT 2020
r...@syspatch-67-arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/
GENERIC.MP
real mem = 1006903296 (960MB)
avail mem = 945872896 (902MB)
mainbus0 at root: Pine64 Rock64
cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu0: 256KB 64b/line 16-way L2 cache
efi0 at mainbus0: UEFI 2.8
efi0: Das U-Boot rev 0x20200100
apm0 at mainbus0
psci0 at mainbus0: PSCI 1.1, SMCCC 1.1
syscon0 at mainbus0: "syscon"
"io-domains" at syscon0 not configured
syscon1 at mainbus0: "power-management"
rkclock0 at mainbus0
rkclock_set_frequency: 0x00000145
rkclock_set_frequency: 0x00000045
rkclock_set_frequency: 0x0000003e
rkclock_set_frequency: 0x000000e5
rkclock_set_frequency: 0x00000092
rkclock_set_frequency: 0x000000dc
rkclock_set_frequency: 0x00000061
ampintc0 at mainbus0 nirq 160, ncpu 4 ipi: 0, 1: "interrupt-controller"
rkpinctrl0 at mainbus0: "pinctrl"
rkgpio0 at rkpinctrl0
rkgpio1 at rkpinctrl0
rkgpio2 at rkpinctrl0
rkgpio3 at rkpinctrl0
"fit-images" at mainbus0 not configured
"opp_table0" at mainbus0 not configured
"arm-pmu" at mainbus0 not configured
agtimer0 at mainbus0: tick rate 24000 KHz
"xin24m" at mainbus0 not configured
com0 at mainbus0: ns16550, no working fifo
com0: console
rkiic0 at mainbus0
iic0 at rkiic0
rkpmic0 at iic0 addr 0x18: RK805
"spi" at mainbus0 not configured
simplebus0 at mainbus0: "amba"
"dmac" at simplebus0 not configured
dwmmc0 at mainbus0: 50 MHz base clock
sdmmc0 at dwmmc0: 4-bit, sd high-speed, mmc high-speed, dma
dwmmc1 at mainbus0: 50 MHz base clock
sdmmc1 at dwmmc1: 8-bit, mmc high-speed, dma
dwge0 at mainbus0: address 6e:71:32:69:67:73
rgephy0 at dwge0 phy 0: RTL8169S/8110S/8211 PHY, rev. 6
ehci0 at mainbus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev
2.00/1.00 addr 1
ohci0 at mainbus0: version 1.0
"usb" at mainbus0 not configured
"external-gmac-clock" at mainbus0 not configured
"sdmmc-regulator" at mainbus0 not configured
"vcc-host-5v-regulator" at mainbus0 not configured
"vcc-sys" at mainbus0 not configured
"dmc" at mainbus0 not configured
"usb" at mainbus0 not configured
cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4
cpu1: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu1: 256KB 64b/line 16-way L2 cache
cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4
cpu2: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu2: 256KB 64b/line 16-way L2 cache
cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4
cpu3: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu3: 256KB 64b/line 16-way L2 cache
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 configuration 1 interface 0 "Generic OHCI root hub" rev
1.00/1.00 addr 1
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SB16G, 0080> removable
sd0: 15193MB, 512 bytes/sector, 31116288 sectors
sdmmc1: can't enable card
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on sd0a (682a6643f5752b65.a) swap on sd0b dump on sd0b
WARNING: bad clock chip time
WARNING: CHECK AND RESET THE DATE!
cpu0: clock not implemented
Lear Zhou
