On Thu, 9 Aug 2018 09:03:54 -0700
jungle Boogie <jungleboog...@gmail.com> wrote:
> Would it be possible for you to print you u-boot environment details
> so that I can compare to mine:
> https://ptpb.pw/y20R
Sure; see below.
Good luck :)
regards,
Robert
U-Boot SPL 2018.09-rc1 (Aug 07 2018 - 22:16:46 -0600)
DRAM: 1024 MiB
Trying to boot from MMC1
U-Boot 2018.09-rc1 (Aug 07 2018 - 22:16:46 -0600) Allwinner Technology
CPU: Allwinner A64 (SUN50I)
Model: FriendlyARM NanoPi A64
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
Loading Environment from FAT... OK
In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
USB2: USB EHCI 1.00
USB3: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 2 0
=> print
arch=arm
baudrate=115200
board=sunxi
board_name=sunxi
boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr}
${prefix}${script}; source ${scriptaddr}
boot_efi_binary=if fdt addr ${fdt_addr_r}; then bootefi bootmgr
${fdt_addr_r};else bootefi bootmgr ${fdtcontroladdr};fi;load ${devtype}
${devnum}:${distro_bootpart} ${kernel_addr_r} efi/boot/bootaa64.efi; if fdt
addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r};else bootefi
${kernel_addr_r} ${fdtcontroladdr};fi
boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr}
${prefix}extlinux/extlinux.conf
boot_net_usb_start=usb start
boot_prefixes=/ /boot/
boot_script_dhcp=boot.scr.uimg
boot_scripts=boot.scr.uimg boot.scr
boot_targets=fel mmc0 usb0 pxe dhcp
bootcmd=run distro_bootcmd
bootcmd_dhcp=run boot_net_usb_start; if dhcp ${scriptaddr} ${boot_script_dhcp};
then source ${scriptaddr}; fi;setenv efi_fdtfile ${fdtfile}; setenv efi_old_vci
${bootp_vci};setenv efi_old_arch ${bootp_arch};setenv bootp_vci
PXEClient:Arch:00011:UNDI:003000;setenv bootp_arch 0xb;if dhcp
${kernel_addr_r}; then tftpboot ${fdt_addr_r} dtb/${efi_fdtfile};if fdt addr
${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r}; else bootefi
${kernel_addr_r} ${fdtcontroladdr};fi;fi;setenv bootp_vci ${efi_old_vci};setenv
bootp_arch ${efi_old_arch};setenv efi_fdtfile;setenv efi_old_arch;setenv
efi_old_vci;
bootcmd_fel=if test -n ${fel_booted} && test -n ${fel_scriptaddr}; then echo
'(FEL boot)'; source ${fel_scriptaddr}; fi
bootcmd_mmc0=setenv devnum 0; run mmc_boot
bootcmd_pxe=run boot_net_usb_start; dhcp; if pxe get; then pxe boot; fi
bootcmd_usb0=setenv devnum 0; run usb_boot
bootdelay=2
bootm_size=0xa000000
console=ttyS0,115200
cpu=armv8
dfu_alt_info_ram=kernel ram 0x40080000 0x1000000;fdt ram 0x4FA00000
0x100000;ramdisk ram 0x4FE00000 0x4000000
distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done
efi_dtb_prefixes=/ /dtb/ /dtb/current/
ethaddr=02:ba:8e:08:47:e5
fdt_addr_r=0x4FA00000
fdtcontroladdr=79f24640
fdtfile=allwinner/sun50i-a64-nanopi-a64.dtb
kernel_addr_r=0x40080000
load_efi_dtb=load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r}
${prefix}${efi_fdtfile}
mmc_boot=if mmc dev ${devnum}; then setenv devtype mmc; run
scan_dev_for_boot_part; fi
mmc_bootdev=0
partitions=name=loader1,start=8k,size=32k,uuid=${uuid_gpt_loader1};name=loader2,size=984k,uuid=${uuid_gpt_loader2};name=esp,size=128M,bootable,uuid=${uuid_gpt_esp};name=system,size=-,uuid=${uuid_gpt_system};
preboot=usb start
pxefile_addr_r=0x4FD00000
ramdisk_addr_r=0x4FE00000
scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for
prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run
scan_dev_for_scripts; done;run scan_dev_for_efi;
scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env
exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if
fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run
scan_dev_for_boot; fi; done
scan_dev_for_efi=setenv efi_fdtfile ${fdtfile}; for prefix in
${efi_dtb_prefixes}; do if test -e ${devtype} ${devnum}:${distro_bootpart}
${prefix}${efi_fdtfile}; then run load_efi_dtb; fi;done;if test -e ${devtype}
${devnum}:${distro_bootpart} efi/boot/bootaa64.efi; then echo Found EFI
removable media binary efi/boot/bootaa64.efi; run boot_efi_binary; echo EFI
LOAD FAILED: continuing...; fi; setenv efi_fdtfile
scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart}
${prefix}extlinux/extlinux.conf; then echo Found
${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED:
continuing...; fi
scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype}
${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script
${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi;
done
scriptaddr=0x4FC00000
serial#=92c000ba8e0847e5
soc=sunxi
stderr=serial,vidconsole
stdin=serial,usbkbd
stdout=serial,vidconsole
usb_boot=usb start; if usb dev ${devnum}; then setenv devtype usb; run
scan_dev_for_boot_part; fi
uuid_gpt_esp=c12a7328-f81f-11d2-ba4b-00a0c93ec93b
uuid_gpt_system=b921b045-1df0-41c3-af44-4c6f280d3fae
Environment size: 4215/131068 bytes
=>
