Thanks Soko -- setting to default boot on the OpenBSD partition didn't
help.
Instead, I had to specify the root device manually to the boot loader
using the -a flag. Without such, I notice the root device is still
pointing to the SD card ??
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
At the bootloader, I use the flag -a
OpenBSD/armv7 BOOTARM 0.5
boot> b sd0a:/bsd -a
Then OpenBSD proposes the root device to be sd0a, for me to confirm.
How can I fix this ?
Issue now is pfctl invocations in /etc/rc is triggering
pfctl: /dev/pf: Device not configured --> does the device pf in
/etc/MAKEDEV require a different numbers for the my A10 device ??
The /etc/rc boot-up continued with failed start-up of daemons:
starting early daemons: syslogd(failed) pflogd(failed).
starting RPC daemons:.
savecore: can't find device 20/14778624
checking quotas: done.
kvm_mkdb: can't open /dev/ksyms
clearing /tmp
kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
starting network daemons: sshd(failed) smtpd(failed) sndiod(failed).
ifconfig: SIOCSIFGATTR: No such file or directory
starting local daemons: cron(failed).
I had to commented-out ntpd to let the boot-up arriving at the login:
prompt !!
Any advice / comment is appreciated !
-- Patrick
On 2017-04-21 09:22, soko.tica wrote:
There is a Linux files partition on your sd0 that is marked bootable.
It
shouldn't be there. FAT32L should, I believe, be marked bootable.
You probably haven't cleared up the disk before the installation
properly.
Clear it by fdisk, mark all partitions blank (zero) and repeat the
installation.
On Thu, Apr 20, 2017 at 5:26 AM, Patrick YU <patrickyu> wrote:
After successfully installing on an Olinuxino A10 board via the SD
card
onto a Toshiba disk with the following MBR partition table, I rebooted
and
again offered to perform another OpenBSD installation. Why ? Thanks
in
advance for any enlightenment !
-- Patrick
# fdisk sd0
Disk: sd0 geometry: 121601/255/63 [1953525168 Sectors]
Offset: 0 Signature: 0xAA55
Starting Ending LBA Info:
#: id C H S - C H S [ start: size ]
------------------------------------------------------------
-------------------
0: 83 0 32 33 - 58743 224 41 [ 2048: 943718400 ]
Linux
files*
1: 0C 58743 224 42 - 58746 109 51 [ 943720448: 40960 ]
FAT32L
2: A6 58746 109 52 - 118795 153 14 [ 943761408: 964689920 ]
OpenBSD
3: 00 0 0 0 - 0 0 0 [ 0: 0 ]
unused
U-Boot 2017.03 (Apr 03 2017 - 11:14:00 -0600) Allwinner Technology
CPU: Allwinner A10 (SUN4I)
Model: Olimex A10-OLinuXino-LIME
I2C: ready
DRAM: 512 MiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
SCSI: Target spinup took 0 ms.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
Net: eth0: ethernet@01c0b000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
USB2: USB EHCI 1.00
USB3: USB OHCI 1.0
scanning bus 0 for devices... 2 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
scanning bus 1 for devices... 1 USB Device(s) found
scanning bus 3 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found EFI removable media binary efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
64684 bytes read in 41 ms (1.5 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
## Starting EFI application at 42000000 ...
Scanning disks on scsi...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 6 disks
OpenBSD/armv7 BOOTARM 0.5
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2151556+7983908+438824 [80+301248+143324]=0xa84fd4
...
sd0 at scsibus0 targ 0 lun 0: <ATA, TOSHIBA MQ01ABD1, AX00> SCSI3
0/direct
fixed naa.5000039514a065a8
sd0: 953869MB, 512 bytes/sector, 1953525168 sectors
...
sd1 at scsibus1 targ 1 lun 0: <Sandisk, SA08G, 0021> SCSI2 0/direct
removable
sd1: 7420MB, 512 bytes/sector, 15196160 sectors
axe0 at uhub0 port 1 configuration 1 interface 0 "ASIX Electronics
AX88772B" rev 2.00/0.01 addr 2
axe0: AX88772B, address 00:00:00:00:00:01
ukphy0 at axe0 phy 16: Generic IEEE 802.3u media interface, rev. 1:
OUI
0x000ec6, model 0x0008
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: preposterous clock chip time
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/armv7 6.1 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? shell
