There is a Linux files partition on your sd0 that is marked bootable. It shouldn't be there. FAT32L should, I believe, be marked bootable.
You probably haven't cleared up the disk before the installation properly. Clear it by fdisk, mark all partitions blank (zero) and repeat the installation. On Thu, Apr 20, 2017 at 5:26 AM, Patrick YU <patric...@yhk.name> wrote: > After successfully installing on an Olinuxino A10 board via the SD card > onto a Toshiba disk with the following MBR partition table, I rebooted and > again offered to perform another OpenBSD installation. Why ? Thanks in > advance for any enlightenment ! > > -- Patrick > > # fdisk sd0 > Disk: sd0 geometry: 121601/255/63 [1953525168 Sectors] > Offset: 0 Signature: 0xAA55 > Starting Ending LBA Info: > #: id C H S - C H S [ start: size ] > ------------------------------------------------------------ > ------------------- > 0: 83 0 32 33 - 58743 224 41 [ 2048: 943718400 ] Linux > files* > 1: 0C 58743 224 42 - 58746 109 51 [ 943720448: 40960 ] FAT32L > 2: A6 58746 109 52 - 118795 153 14 [ 943761408: 964689920 ] OpenBSD > 3: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused > > U-Boot 2017.03 (Apr 03 2017 - 11:14:00 -0600) Allwinner Technology > > CPU: Allwinner A10 (SUN4I) > Model: Olimex A10-OLinuXino-LIME > I2C: ready > DRAM: 512 MiB > MMC: SUNXI SD/MMC: 0 > *** Warning - bad CRC, using default environment > > In: serial > Out: serial > Err: serial > SCSI: Target spinup took 0 ms. > AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode > flags: ncq stag pm led clo only pmp pio slum part ccc apst > Net: eth0: ethernet@01c0b000 > starting USB... > USB0: USB EHCI 1.00 > USB1: USB OHCI 1.0 > USB2: USB EHCI 1.00 > USB3: USB OHCI 1.0 > scanning bus 0 for devices... 2 USB Device(s) found > scanning bus 2 for devices... 1 USB Device(s) found > scanning bus 1 for devices... 1 USB Device(s) found > scanning bus 3 for devices... 2 USB Device(s) found > scanning usb for storage devices... 0 Storage Device(s) found > Hit any key to stop autoboot: 0 > switch to partitions #0, OK > mmc0 is current device > Scanning mmc 0:1... > Found EFI removable media binary efi/boot/bootarm.efi > reading efi/boot/bootarm.efi > 64684 bytes read in 41 ms (1.5 MiB/s) > libfdt fdt_check_header(): FDT_ERR_BADMAGIC > ## Starting EFI application at 42000000 ... > Scanning disks on scsi... > Scanning disks on usb... > Scanning disks on mmc... > MMC Device 1 not found > MMC Device 2 not found > MMC Device 3 not found > Found 6 disks > >> OpenBSD/armv7 BOOTARM 0.5 >>> >> boot> > cannot open sd0a:/etc/random.seed: No such file or directory > booting sd0a:/bsd: 2151556+7983908+438824 [80+301248+143324]=0xa84fd4 > > ... > sd0 at scsibus0 targ 0 lun 0: <ATA, TOSHIBA MQ01ABD1, AX00> SCSI3 0/direct > fixed naa.5000039514a065a8 > sd0: 953869MB, 512 bytes/sector, 1953525168 sectors > ... > sd1 at scsibus1 targ 1 lun 0: <Sandisk, SA08G, 0021> SCSI2 0/direct > removable > sd1: 7420MB, 512 bytes/sector, 15196160 sectors > axe0 at uhub0 port 1 configuration 1 interface 0 "ASIX Electronics > AX88772B" rev 2.00/0.01 addr 2 > axe0: AX88772B, address 00:00:00:00:00:01 > ukphy0 at axe0 phy 16: Generic IEEE 802.3u media interface, rev. 1: OUI > 0x000ec6, model 0x0008 > boot device: sd0 > root on rd0a swap on rd0b dump on rd0b > WARNING: preposterous clock chip time > WARNING: CHECK AND RESET THE DATE! > erase ^?, werase ^W, kill ^U, intr ^C, status ^T > > Welcome to the OpenBSD/armv7 6.1 installation program. > (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? shell > >
