On Sat, Aug 06, 2016 at 12:51:37AM +0200, Patrick Wildt wrote: > On Fri, Aug 05, 2016 at 04:51:55PM -0300, Daniel Bolgheroni wrote: > > On Thu, Aug 04, 2016 at 04:32:09PM +0200, Patrick Wildt wrote: > > > Mark just committed a diff that should fix this issue. :-) > > > > I was going to report this after making sure it's not something related > > to the network the board is attached. > > > > Before r1.12 and r1.13, as the last commits refers to it, there were some > > issues related to auto negotiation. It was pointed out to manually set > > media to > > 100baseTX, since the board was hooked in a Fast Ethernet switch. OK, so I > > had > > this at hostname.fec0: > > > > inet 192.168.1.3 255.255.255.0 > > media 100baseTX > > mediaopt full-duplex > > > > However, I noticed that after rebooting, the interface aparently was going > > up > > but I couldn't ping it. Only after issuing a "ifconfig fec0" that the > > interface > > was becoming functional. > > > > After the last update, now with r1.12 and r1.13, the same hostname.fec0, > > there > > is no network at all. Without the media/mediaopt the result is the same. > > > > Thank you. > > > > -- > > $ vmstat -zi > > interrupt total rate > > irq1023/spur 144 0 > > irq58/imxuart0 170 0 > > irq75/imxehci0 0 0 > > irq72/imxehci1 0 0 > > irq54/imxesdhc0 40 0 > > irq55/imxesdhc1 4 0 > > irq56/imxesdhc2 21427 11 > > irq60/imxuart1 0 0 > > irq29/tick 389215 199 > > Total 411000 211 > > $ > > > > OpenBSD 6.0-current (GENERIC) #0: Thu Aug 4 15:46:32 BRT 2016 > > dbolgher...@wbs.my.domain:/usr/src/sys/arch/armv7/compile/GENERIC > > real mem = 536870912 (512MB) > > avail mem = 518017024 (494MB) > > mainbus0 at root: Wandboard i.MX6 Dual Lite Board rev B1 > > cpu0 at mainbus0: ARM Cortex A9 R2 rev 10 (ARMv7 core) > > cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled > > cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache > > cortex0 at mainbus0 > > amptimer0 at cortex0: tick rate 396000 KHz > > armliicc0 at cortex0: rtl 8 waymask: 0x0000000f > > imx0 at mainbus0 > > imxccm0 at imx0: imx6 rev 1.1 CPU freq: 792 MHz > > imxiomuxc0 at imx0 > > imxocotp0 at imx0 > > simplebus0 at mainbus0: "soc" > > ampintc0 at simplebus0 nirq 160 > > simplebus1 at simplebus0: "aips-bus" > > simplebus2 at simplebus1: "spba-bus" > > imxuart0 at simplebus2: console > > imxgpio0 at simplebus1 > > imxgpio1 at simplebus1 > > imxgpio2 at simplebus1 > > imxgpio3 at simplebus1 > > imxgpio4 at simplebus1 > > imxgpio5 at simplebus1 > > imxgpio6 at simplebus1 > > imxdog0 at simplebus1 > > simplebus3 at simplebus1: "anatop" > > imxgpc0 at simplebus1 > > simplebus4 at simplebus0: "aips-bus" > > imxehci0 at simplebus4 > > usb0 at imxehci0: USB revision 2.0 > > uhub0 at usb0 "i.MX6 EHCI root hub" rev 2.00/1.00 addr 1 > > imxehci1 at simplebus4 > > usb1 at imxehci1: USB revision 2.0 > > uhub1 at usb1 "i.MX6 EHCI root hub" rev 2.00/1.00 addr 1 > > fec0 at simplebus4 > > fec0: address 00:1f:7b:b0:08:52 > > atphy0 at fec0 phy 1: AR8035 10/100/1000 PHY, rev. 4 > > imxesdhc0 at simplebus4 > > imxesdhc0: 198 MHz base clock > > sdmmc0 at imxesdhc0: 4-bit, mmc high-speed, dma > > imxesdhc1 at simplebus4 > > imxesdhc1: 198 MHz base clock > > sdmmc1 at imxesdhc1: 4-bit, mmc high-speed, dma > > imxesdhc2 at simplebus4 > > imxesdhc2: 198 MHz base clock > > sdmmc2 at imxesdhc2: 4-bit, mmc high-speed, dma > > imxiic0 at simplebus4 > > iic0 at imxiic0 > > imxiic1 at simplebus4 > > iic1 at imxiic1 > > "fsl,sgtl5000" at iic1 addr 0xa not configured > > imxuart1 at simplebus4 > > simplebus5 at mainbus0: "regulators" > > sdmmc1: can't enable card > > scsibus0 at sdmmc0: 2 targets, initiator 0 > > sd0 at scsibus0 targ 1 lun 0: <SD/MMC, 00000, 0010> SCSI2 0/direct fixed > > sd0: 1910MB, 512 bytes/sector, 3911680 sectors > > scsibus1 at sdmmc2: 2 targets, initiator 0 > > sd1 at scsibus1 targ 1 lun 0: <SD/MMC, SU08G, 0080> SCSI2 0/direct fixed > > sd1: 7580MB, 512 bytes/sector, 15523840 sectors > > vscsi0 at root > > scsibus2 at vscsi0: 256 targets > > softraid0 at root > > scsibus3 at softraid0: 256 targets > > boot device: sd0 > > root on sd1a (8202d1873078fd2f.a) swap on sd1b dump on sd1b > > WARNING: CHECK AND RESET THE DATE! > > > > -- > > db > > > > This is most probably caused by another commit: > > http://marc.info/?l=openbsd-cvs&m=147032600711022&w=2 > > You can see that in the vmstat output there is no fec0. This means it > never got established. And that is because of that commit, as expected. > We're working on resolving that issue though. > > If you back this diff out it should work again. >
I just committed a diff that should make your Wandboard work again for good. Let me know if that helps.
