Hi Eric,
I tried that and found that I needed to detach and remove
the spare before replacing the failed disk with the spare
disk.
What actually worked is below.
Thanks,
Cindy
# zpool status test
pool: test
state: DEGRADED
status: One or more devices could not be opened. Sufficient replicas
exist for
the pool to continue functioning in a degraded state.
action: Attach the missing device and online it using 'zpool online'.
see: http://www.sun.com/msg/ZFS-8000-2Q
scrub: resilver completed after 0h0m with 0 errors on Wed Oct 14
14:24:57 2009
config:
NAME STATE READ WRITE CKSUM
test DEGRADED 0 0 0
raidz1-0 DEGRADED 0 0 0
c0t4d0 ONLINE 0 0 0
c0t5d0 ONLINE 0 0 0
spare-2 DEGRADED 0 0 19
c0t6d0 UNAVAIL 0 0 0 cannot open
c0t7d0 ONLINE 0 0 0 32K resilvered
spares
c0t7d0 INUSE currently in use
errors: No known data errors
# zpool detach test c0t7d0
# zpool remove test c0t7d0
# zpool replace test c0t6d0 c0t7d0
# zpool status test
pool: test
state: ONLINE
scrub: resilver completed after 0h0m with 0 errors on Wed Oct 14
14:25:47 2009
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
raidz1-0 ONLINE 0 0 0
c0t4d0 ONLINE 0 0 0
c0t5d0 ONLINE 0 0 0
c0t7d0 ONLINE 0 0 0 48.5K resilvered
errors: No known data errors
On 10/14/09 15:23, Eric Schrock wrote:
On 10/14/09 14:17, Cindy Swearingen wrote:
Hi Jason,
I think you are asking how do you tell ZFS that you want to replace the
failed disk c8t7d0 with the spare, c8t11d0?
I just tried do this on my Nevada build 124 lab system, simulating a
disk failure and using zpool replace to replace the failed disk with
the spare. The spare is now busy and it fails. This has to be a bug.
You need to 'zpool detach' the original (c8t7d0).
- Eric
Another way to recover is if you have a replacement disk for c8t7d0,
like this:
1. Physically replace c8t7d0.
You might have to unconfigure the disk first. It depends
on the hardware.
2. Tell ZFS that you replaced it.
# zpool replace tank c8t7d0
3. Detach the spare.
# zpool detach tank c8t11d0
4. Clear the pool or the device specifically.
# zpool clear tank c8t7d0
Cindy
On 10/14/09 14:44, Jason Frank wrote:
So, my Areca controller has been complaining via email of read errors
for a couple days on SATA channel 8. The disk finally gave up last
night at 17:40. I got to say I really appreciate the Areca
controller taking such good care of me.
For some reason, I wasn't able to log into the server last night or
in the morning, probably because my home dir was on the zpool with
the failed disk (although it's a raidz2, so I don't know why that was
a problem.) So, I went ahead and rebooted it the hard way this morning.
The reboot went OK, and I was able to get access to my home directory
by waiting about 5 minutes after authenticating. I checked my zpool,
and it was resilvering. But, it had only been running for a few
minutes. Evidently, it didn't start resilvering until I rebooted
it. I would have expected it to do that when the disk failed last
night (I had set up a hot spare disk already).
All of the zpool commands were taking minutes to complete while
c8t7d0 was UNAVAIL, so I offline'd it. When I say all, that includes
iostat, status, upgrade, just about anything non-destructive that I
could try. That was a little odd. Once I offlined the drive, my
resilver restarted, which surprised me. After all, I simply changed
an UNAVAIL drive to OFFLINE, in either case, you can't use it for
operations. But no big deal there. That fixed the login slowness
and the zpool command slowness.
The resilver completed, and now I'm left with the following zpool
config. I'm not sure how to get things back to normal though, and I
hate to do something stupid...
r...@datasrv1:~# zpool status tank
pool: tank
state: DEGRADED
scrub: scrub stopped after 0h10m with 0 errors on Wed Oct 14
15:23:06 2009
config:
NAME STATE READ WRITE CKSUM
tank DEGRADED 0 0 0
raidz2 DEGRADED 0 0 0
c8t0d0 ONLINE 0 0 0
c8t1d0 ONLINE 0 0 0
c8t2d0 ONLINE 0 0 0
c8t3d0 ONLINE 0 0 0
c8t4d0 ONLINE 0 0 0
c8t5d0 ONLINE 0 0 0
c8t6d0 ONLINE 0 0 0
spare DEGRADED 0 0 0
c8t7d0 REMOVED 0 0 0
c8t11d0 ONLINE 0 0 0
c8t8d0 ONLINE 0 0 0
c8t9d0 ONLINE 0 0 0
c8t10d0 ONLINE 0 0 0
spares
c8t11d0 INUSE currently in use
Since it's not obvious, the spare line had both t7 and t11 indented
under it.
When the resilver completed, I yanked the hard drive on target 7.
I'm assuming that t11 has the same content as t7, but that's not
necessarily clear from the output above.
So, now I'm left with the following config. I can't zfs remove t7,
because it's not a hot spare or a cache disk. I can't zfs replace t7
with t11, I'm told that t11 is busy. And I didn't see any other
zpool subcommands that look likely to fix the problem.
Here are my system details:
SunOS datasrv1 5.11 snv_118 i86pc i386 i86xpv Solaris
This system is currently running ZFS pool version 16.
Pool 'tank' is already formatted using the current version.
How do I tell the system that t11 is the replacement for t7, and how
to I then add t7 as the hot spare (after I replace the disk)?
Thanks
_______________________________________________
zfs-discuss mailing list
zfs-discuss@opensolaris.org
http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
_______________________________________________
zfs-discuss mailing list
zfs-discuss@opensolaris.org
http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
