Hi, On 4 April 2017 09:48:32 BST, Andrea Galbusera <giz...@gmail.com> wrote: >On Fri, Mar 24, 2017 at 6:49 PM, Trevor Woerner <twoer...@gmail.com> >wrote: > >> Add support for the Waveshare 1024x600 "C" Rev2.1 7" IPS Capacitive >Touch >> Screen LCD with HDMI interface: >> >> http://www.waveshare.com/7inch-HDMI-LCD-C.htm >> http://www.waveshare.com/wiki/7inch_HDMI_LCD_(C) >> >> This product works "out of the box" with the Raspberry Pi. Simply >connect >> the provided HDMI and USB cables between the two devices. The >touch<=>mouse >> integration works automatically. >> >> Tested with a Raspberry Pi 3, with a 32-bit raspberrypi3 build. >> >> Signed-off-by: Trevor Woerner <twoer...@gmail.com> >> --- >> README | 13 ++++++++++--- >> recipes-bsp/bootfiles/rpi-config_git.bb | 10 ++++++++++ >> 2 files changed, 20 insertions(+), 3 deletions(-) >> >> diff --git a/README b/README >> index 65a1e5f..c58bc99 100644 >> --- a/README >> +++ b/README >> @@ -29,7 +29,8 @@ Contents: >> 3.L. Enable SPI bus >> 3.M. Enable I2C >> 3.N. Enable PiTFT support >> - 3.O. Enable UART support >> + 3.O. Misc. display >> + 3.P. Enable UART support >> 4. Extra apps >> 4.A. omxplayer >> 5. Board Configuration >> @@ -241,9 +242,15 @@ List of currently supported models: >> - pitft22 >> - pitft28r >> >> -3.O. Enable UART >> -=============== >> +3.O. Misc. display >> +================== >> +If you would like to use the Waveshare "C" 1024×600, 7 inch >Capacitive >> Touch >> +Screen LCD, HDMI interface >(http://www.waveshare.com/7inch-HDMI-LCD-C.htm >> ) >> +Rev 2.1, please set the following in your local.conf >> +WAVESHARE_1024X600_C_2.1 = "1" >> >> +3.P. Enable UART >> +=============== >> RaspberryPi 1, 2 and CM will have UART console enabled by default. >> >> RaspberryPi 3 does not have the UART enabled by default because this >> needs a >> diff --git a/recipes-bsp/bootfiles/rpi-config_git.bb >> b/recipes-bsp/bootfiles/rpi-config_git.bb >> index 20ec343..8adc938 100644 >> --- a/recipes-bsp/bootfiles/rpi-config_git.bb >> +++ b/recipes-bsp/bootfiles/rpi-config_git.bb >> @@ -110,6 +110,16 @@ do_deploy() { >> echo "# Enable VC4 Graphics" >> ${DEPLOYDIR}/bcm2835- >> bootfiles/config.txt >> echo "dtoverlay=vc4-kms-v3d,${VC4_CMA_SIZE}" >> >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt >> fi >> + >> + # Waveshare "C" 1024x600 7" Rev2.1 IPS capacitive touch ( >> http://www.waveshare.com/7inch-HDMI-LCD-C.htm) >> + if [ "${WAVESHARE_1024X600_C_2.1}" = "1" ]; then >> + echo "# Waveshare \"C\" 1024x600 7\" Rev2.1 IPS capacitive >touch >> screen" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt >> + echo "max_usb_current=1" >> ${DEPLOYDIR}/bcm2835- >> bootfiles/config.txt >> + echo "hdmi_group=2" >> >${DEPLOYDIR}/bcm2835-bootfiles/config.txt >> + echo "hdmi_mode=87" >> >${DEPLOYDIR}/bcm2835-bootfiles/config.txt >> + echo "hdmi_cvt 1024 600 60 6 0 0 0" >> ${DEPLOYDIR}/bcm2835- >> bootfiles/config.txt >> + echo "hdmi_drive=1" >> >${DEPLOYDIR}/bcm2835-bootfiles/config.txt >> + fi >> } >> >> do_deploy_append_raspberrypi3-64() { >> -- >> 2.12.0.rc1.48.g076c053 >> >> -- >> _______________________________________________ >> yocto mailing list >> yocto@yoctoproject.org >> https://lists.yoctoproject.org/listinfo/yocto >> > > >After applying this commit the build fails with: > >ERROR: rpi-config-git-r5 do_deploy: Function failed: do_deploy (log >file is >located at >/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/temp/log.do_deploy.32154) >ERROR: Logfile of failure stored in: >/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/temp/log.do_deploy.32154 >Log data follows: >| DEBUG: Executing python function sstate_task_prefunc >| DEBUG: Removing manifest: >/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/deploy/images/raspberrypi3/bcm2835-bootfiles/config.txt >| DEBUG: Removing manifest: >/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/deploy/images/raspberrypi3/bcm2835-bootfiles/ >| DEBUG: Python function sstate_task_prefunc finished >| DEBUG: Executing shell function do_deploy >| >/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/temp/run.do_deploy.32154: >192: >/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/temp/run.do_deploy.32154: >Bad substitution >| WARNING: exit code 2 from a shell command. >| ERROR: Function failed: do_deploy (log file is located at >/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/temp/log.do_deploy.32154) >ERROR: Task >(/home/gizero/work/smartliving/distro/repo-master/build-poky/conf/../../layers/meta-raspberrypi/recipes-bsp/bootfiles/rpi-config_git.bb:do_deploy) >failed with exit code '1' >NOTE: Tasks Summary: Attempted 4857 tasks of which 4855 didn't need to >be >rerun and 1 failed. > >Still to look at it closer... maybe related to some shell configuration >on >my side?
That is strange. Do you get any additional information? Can't pick anything from the posted log. -- Andrei Gherzan gpg: rsa4096/D4D94F67AD0E9640 | t: @agherzan -- _______________________________________________ yocto mailing list yocto@yoctoproject.org https://lists.yoctoproject.org/listinfo/yocto
