Ok. Any suggestions?
vince schrieb am Dienstag, 2. Dezember 2025 um 20:42:19 UTC+1:
Then follow the old sysadmin motto of "when in doubt comment it
out" and see if that helps any.
On Tuesday, December 2, 2025 at 11:25:13 AM UTC-8 Zed wrote:
Off course, i did restart weewx ;-)
vince schrieb am Dienstag, 2. Dezember 2025 um 19:01:03 UTC+1:
Edit the driver and restart weewx
On Tuesday, December 2, 2025 at 9:45:44 AM UTC-8 Zed wrote:
Yes, it's bme280wx from WJCarpenter
<https://gitlab.com/wjcarpenter/bme280wx/-/blob/master/README.md>.
In ~weewx/weewx-data/bin/user/bme280wx.py I changed:
# loginf('BME280 data %s' % bme280data)
logdbg('BME280 data %s' % bme280data)
But no change (debug=0):
Dez 02 18:42:46 raspberrypi-W weewxd.py[394495]:
bme280: {'outHumidity': 98.0, 'outTemp': 5.1,
'windDir': 135.0, 'rain_total': 910.0, 'windSpeed':
0.0, 'outTempBatteryStatus': 1, 'dateTime':
1764697363, 'usUnits': 17, 'rain': 0.0, 'pressure':
996.8794121453019, 'inTemp': 20.87991048009717,
'inHumidity': 47.00716895052753}
Dez 02 18:42:59 raspberrypi-W weewxd.py[394495]:
bme280: BME280 data
compensated_reading(id=90b874ac-5f0e-4dee-ab91-6ff37be85f0f,
timestamp=2025-12-02 17:42:59.009837UTC, temp=20.905
°C, pressure=996.95 hPa, humidity=47.03 % rH)
Dez 02 18:42:59 raspberrypi-W weewxd.py[394495]:
bme280: {'outHumidity': 98.0, 'outTemp': 5.1,
'windDir': 135.0, 'rain_total': 910.0, 'windSpeed':
0.0, 'outTempBatteryStatus': 1, 'dateTime':
1764697375, 'usUnits': 17, 'rain': 0.0, 'pressure':
996.9454680536317, 'inTemp': 20.905063962284476,
'inHumidity': 47.0306761168033}
Dez 02 18:43:10 raspberrypi-W weewxd.py[394495]:
bme280: BME280 data
compensated_reading(id=e62d5c77-9d93-45ca-a37c-f2050e454beb,
timestamp=2025-12-02 17:43:10.939289UTC, temp=20.870
°C, pressure=996.95 hPa, humidity=47.02 % rH)
This looks to me, like the log-messages are written
by weewxd.py.
vince schrieb am Dienstag, 2. Dezember 2025 um
17:48:49 UTC+1:
You didn't say which bme280 driver you are using,
but if you are using the one from WJCarpenter
there are a couple places in the new_loop_packet(
) routine that use loginf( ) to log every packet
twice. You could change that to logdbg( ) in each
place to quiet it down to only logging if you have
debug=1 in weewx.conf
On Tuesday, December 2, 2025 at 2:07:30 AM UTC-8
Zed wrote:
I had to upgrade my VEnv-installation from
4.9.1 to 5.2.0.
Since then for every measurement i see a
record like these in the log:
Dez 01 23:36:59 server weewxd.py[165343]:
bme280: {'outHumidity': 84.0, 'outTemp': 2.6,
'windDir': 180.0, 'rain_total': 908.8,
'windSpeed': 0.0, 'outTempBatteryStatus': 1,
'dateTime': 1764628616, 'usUnits': 17, 'rain':
None, 'pressure': 997.3836082289309, 'inTemp':
19.531694481620796, 'inHumidity':
48.77856343381041}
Dez 01 23:37:11 server weewxd.py[165343]:
bme280: BME280 data
compensated_reading(id=2e17ef34-6cf1-4a6c-9198-e2754bdbd3b3,
timestamp=2025-12-01 22:37:11.402537UTC,
temp=19.512 °C, pressure=997.33 hPa,
humidity=49.07 % rH)
Dez 01 23:37:11 server weewxd.py[165343]:
bme280: {'outHumidity': 84.0, 'outTemp': 2.6,
'windDir': 180.0, 'rain_total': 908.8,
'windSpeed': 0.0, 'outTempBatteryStatus': 1,
'dateTime': 1764628628, 'usUnits': 17, 'rain':
0.0, 'pressure': 997.3252012242718, 'inTemp':
19.511572013102704, 'inHumidity':
49.071948952003744}
No matter what debug-level is set.
Is there a switch to turn these messages off?
