As the subject says, nearly five years to the day, data quit archiving. It is no longer written to MySQL or Wunderground. In an effort to fix this I have: rebooted, disconnected and reconnected the usb cable to the data collector, upgraded weewx, uninstall (purge) and reinstall, and created a new conf file. If I run weewxd from the cli, I can see the data coming in and verified it's current. I have verified the connection to MySQL. I'm out of good ideas. Thanks for your assistance!
Log file with debug=2 attached with about 13 minutes of data.
Here is some info from wee_debug:
Using verbosity=1, displaying most info
wee_debug output will be sent to stdout(console)
Using configuration file /etc/weewx/weewx.conf
Using database binding 'wx_binding', which is bound to database
'archive_mysql'
System info
Platform: Linux-5.10.103-v7+-armv7l-with-debian-10.12
Python Version: 3.7.3
Load Information
1 minute load average: 0.80
5 minute load average: 0.68
15 minute load average: 0.70
General Weewx info
Weewx version 4.7.0 detected.
Station info
Station type: Vantage
Driver: weewx.drivers.vantage
Driver info
[Vantage]
# This section is for the Davis Vantage series of weather stations.
# Connection type: serial or ethernet
# serial (the classic VantagePro)
# ethernet (the WeatherLinkIP or Serial-Ethernet bridge)
type = serial
# If the connection type is serial, a port must be specified:
# Debian, Ubuntu, Redhat, Fedora, and SuSE:
# /dev/ttyUSB0 is a common USB port name
# /dev/ttyS0 is a common serial port name
# BSD:
# /dev/cuaU0 is a common serial port name
port = /dev/ttyUSB0
# If the connection type is ethernet, an IP Address/hostname is
required:
host = 1.2.3.4
######################################################
# The rest of this section rarely needs any attention.
# You can safely leave it "as is."
######################################################
# Serial baud rate (usually 19200)
baudrate = 19200
# TCP port (when using the WeatherLinkIP)
tcp_port = 22222
# TCP send delay (when using the WeatherLinkIP):
tcp_send_delay = 0.5
# The type of LOOP packet to request: 1 = LOOP1; 2 = LOOP2; 3 = both
loop_request = 1
# The id of your ISS station (usually 1). If you use a wind meter
connected
# to a anemometer transmitter kit, use its id
iss_id = 1
# How long to wait for a response from the station before giving up (in
# seconds; must be greater than 2)
timeout = 4
# How long to wait before trying again (in seconds)
wait_before_retry = 1.2
# How many times to try before giving up:
max_tries = 4
# Vantage model Type: 1 = Vantage Pro; 2 = Vantage Pro2
model_type = 2
# The driver to use:
driver = weewx.drivers.vantage
Currently installed extensions
No extensions installed
Archive info
Database name: weewx
Table name: archive
Version 1.0
Unit system: 1 (US)
First good timestamp: 2017-03-09 19:00:00 PST (1489114800)
Last good timestamp: 2022-03-13 03:00:00 PDT (1647165600)
Number of records: 87129
weewx (weewx.conf) is set to use an archive interval of 300 seconds.
The station hardware was not interrogated in determining archive interval.
Databases configured in weewx.conf
Database name: weewx.sdb
Database driver: weedb.sqlite
Database name: weewx
Database driver: weedb.mysql
Database host: 192.168.1.17
Parsed and obfuscated weewx.conf
# WEEWX CONFIGURATION FILE
#
# Copyright (c) 2009-2021 Tom Keffer <[email protected]>
# See the file LICENSE.txt for your rights.
##############################################################################
# This section is for general configuration information.
# Set to 1 for extra debug info, otherwise comment it out or set to zero
debug = 2
# Root directory of the weewx data file hierarchy for this station
WEEWX_ROOT = /
# Whether to log successful operations
log_success = True
# Whether to log unsuccessful operations
log_failure = True
# How long to wait before timing out a socket (FTP, HTTP) connection
socket_timeout = 20
# Do not modify this. It is used when installing and updating weewx.
version = 4.7.0
##############################################################################
# This section is for information about the station.
[Station]
# removed
##############################################################################
[Vantage]
# This section is for the Davis Vantage series of weather stations.
# Connection type: serial or ethernet
# serial (the classic VantagePro)
# ethernet (the WeatherLinkIP or Serial-Ethernet bridge)
type = serial
# If the connection type is serial, a port must be specified:
# Debian, Ubuntu, Redhat, Fedora, and SuSE:
# /dev/ttyUSB0 is a common USB port name
# /dev/ttyS0 is a common serial port name
# BSD:
# /dev/cuaU0 is a common serial port name
port = /dev/ttyUSB0
# If the connection type is ethernet, an IP Address/hostname is
required:
host = 1.2.3.4
######################################################
# The rest of this section rarely needs any attention.
# You can safely leave it "as is."
######################################################
# Serial baud rate (usually 19200)
baudrate = 19200
# TCP port (when using the WeatherLinkIP)
tcp_port = 22222
# TCP send delay (when using the WeatherLinkIP):
tcp_send_delay = 0.5
# The type of LOOP packet to request: 1 = LOOP1; 2 = LOOP2; 3 = both
loop_request = 1
# The id of your ISS station (usually 1). If you use a wind meter
connected
# to a anemometer transmitter kit, use its id
iss_id = 1
# How long to wait for a response from the station before giving up (in
# seconds; must be greater than 2)
timeout = 4
# How long to wait before trying again (in seconds)
wait_before_retry = 1.2
# How many times to try before giving up:
max_tries = 4
# Vantage model Type: 1 = Vantage Pro; 2 = Vantage Pro2
model_type = 2
# The driver to use:
driver = weewx.drivers.vantage
##############################################################################
# This section is for uploading data to Internet sites
[StdRESTful]
[[Wunderground]]
# This section is for configuring posts to the Weather Underground.
# If you wish to post to the Weather Underground, set the option
'enable' to true, then
# specify a station (e.g., 'KORHOODR3') and password. To guard
against parsing errors, put
# the password in quotes.
enable = true
station = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
# If you plan on using wunderfixer, set the following
# to your API key:
api_key = XXX obfuscated by wee_debug XXX
# Set the following to True to have weewx use the WU "Rapidfire"
# protocol. Not all hardware can support it. See the User's Guide.
rapidfire = False
##############################################################################
# This section specifies what reports, using which skins, to generate.
[StdReport]
# Where the skins reside, relative to WEEWX_ROOT
SKIN_ROOT = /etc/weewx/skins
# Where the generated reports should go, relative to WEEWX_ROOT
HTML_ROOT = /var/www/html/weewx
# The database binding indicates which data should be used in reports.
data_binding = wx_binding
# Whether to log a successful operation
log_success = True
# Whether to log an unsuccessful operation
log_failure = True
# Each of the following subsections defines a report that will be run.
# See the customizing guide to change the units, plot types and line
# colors, modify the fonts, display additional sensor data, and other
# customizations. Many of those changes can be made here by overriding
# parameters, or by modifying templates within the skin itself.
[[SeasonsReport]]
# The SeasonsReport uses the 'Seasons' skin, which contains the
# images, templates and plots for the report.
skin = Seasons
enable = true
[[SmartphoneReport]]
# The SmartphoneReport uses the 'Smartphone' skin, and the images
and
# files are placed in a dedicated subdirectory.
skin = Smartphone
enable = false
HTML_ROOT = /var/www/html/weewx/smartphone
[[MobileReport]]
# The MobileReport uses the 'Mobile' skin, and the images and files
# are placed in a dedicated subdirectory.
skin = Mobile
enable = false
HTML_ROOT = /var/www/html/weewx/mobile
[[StandardReport]]
# This is the old "Standard" skin. By default, it is not enabled.
skin = Standard
enable = false
[[FTP]]
# FTP'ing the results to a webserver is treated as just another
report,
# albeit one with an unusual report generator!
skin = Ftp
# If you wish to use FTP, set "enable" to "true", then
# fill out the next four lines.
# Use quotes around passwords to guard against parsing errors.
enable = false
user = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
server = replace_me # The ftp server name, e.g, www.myserver.org
path = replace_me # The destination directory, e.g., /weather
# Set to True for an FTP over TLS (FTPS) connection. Not all servers
# support this.
secure_ftp = False
# To upload files from something other than what HTML_ROOT is set
# to above, specify a different HTML_ROOT here.
#HTML_ROOT = /var/www/html/weewx
# Most FTP servers use port 21
port = 21
# Set to 1 to use passive mode, zero for active mode
passive = 1
[[RSYNC]]
# rsync'ing to a webserver is treated as just another report
skin = Rsync
# If you wish to use rsync, you must configure passwordless ssh
using
# public/private key authentication from the user account that weewx
# runs to the user account on the remote machine where the files
# will be copied.
#
# If you wish to use rsync, set "enable" to "true", then
# fill out server, user, and path.
# The server should appear in your .ssh/config file.
# The user is the username used in the identity file.
# The path is the destination directory, such as
/var/www/html/weather.
# Be sure that the user has write permissions on the destination!
enable = false
server = replace_me
user = XXX obfuscated by wee_debug XXX
path = replace_me
# To upload files from something other than what HTML_ROOT is set
# to above, specify a different HTML_ROOT here.
#HTML_ROOT = /var/www/html/weewx
# Rsync can be configured to remove files from the remote server if
# they don't exist under HTML_ROOT locally. USE WITH CAUTION: if you
# make a mistake in the remote path, you could could unintentionally
# cause unrelated files to be deleted. Set to 1 to enable remote
file
# deletion, zero to allow files to accumulate remotely.
delete = 0
# Options in the [[Defaults]] section below will apply to all reports.
# What follows are a few of the more popular options you may want to
# uncomment, then change.
[[Defaults]]
# Which language to use for all reports. Not all skins support all
languages.
# You can override this for individual reports.
lang = en
# Which unit system to use for all reports. Choices are 'us',
'metric', or 'metricwx'.
# You can override this for individual reports.
unit_system = us
[[[Units]]]
# Option "unit_system" above sets the general unit system, but
overriding specific unit
# groups is possible. These are popular choices. Uncomment and
set as appropriate.
# NB: The unit is always in the singular. I.e., 'mile_per_hour',
# NOT 'miles_per_hour'
[[[[Groups]]]]
# group_altitude = meter # Options are
'foot' or 'meter'
# group_pressure = mbar # Options are
'inHg', 'mmHg', 'mbar', or 'hPa'
# group_rain = mm # Options are
'inch', 'cm', or 'mm'
# group_rainrate = mm_per_hour # Options are
'inch_per_hour', 'cm_per_hour', or 'mm_per_hour'
# group_temperature = degree_C # Options are
'degree_C', 'degree_F', or 'degree_K'
# The following line is used to keep the above lines
indented properly.
# It can be ignored.
unused = unused
# Uncommenting the following section frequently results in more
# attractive formatting of times and dates, but may not work in
# your locale.
[[[[TimeFormats]]]]
# day = %H:%M
# week = %H:%M on %A
# month = %d-%b-%Y %H:%M
# year = %d-%b-%Y %H:%M
# rainyear = %d-%b-%Y %H:%M
# current = %d-%b-%Y %H:%M
# ephem_day = %H:%M
# ephem_year = %d-%b-%Y %H:%M
# The following line is used to keep the above lines
indented properly.
# It can be ignored.
unused = unused
[[[Labels]]]
# Users frequently change the labels for these observation types
[[[[Generic]]]]
# inHumidity = Inside Humidity
# inTemp = Inside Temperature
# outHumidity = Outside Humidity
# outTemp = Outside Temperature
# extraTemp1 = Temperature1
# extraTemp2 = Temperature2
# extraTemp3 = Temperature3
# The following line is used to keep the above lines
indented properly.
# It can be ignored.
unused = unused
##############################################################################
# This service acts as a filter, converting the unit system coming from
# the hardware to a unit system in the database.
[StdConvert]
# The target_unit affects only the unit system in the database. Once
# chosen it cannot be changed without converting the entire database.
# Modification of target_unit after starting weewx will result in
# corrupt data - the database will contain a mix of US and METRIC data.
#
# The value of target_unit does not affect the unit system for
# reporting - reports can display US, Metric, or any combination of
units.
#
# In most cases, target_unit should be left as the default: US
#
# In particular, those migrating from a standard wview installation
# should use US since that is what the wview database contains.
# DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING!
target_unit = US # Options are 'US', 'METRICWX', or 'METRIC'
##############################################################################
# This section can adjust data using calibration expressions.
[StdCalibrate]
[[Corrections]]
# For each type, an arbitrary calibration expression can be given.
# It should be in the units defined in the StdConvert section.
# Example:
foo = foo + 0.2
##############################################################################
# This section is for quality control checks. If units are not specified,
# values must be in the units defined in the StdConvert section.
[StdQC]
[[MinMax]]
barometer = 26, 32.5, inHg
pressure = 24, 34.5, inHg
outTemp = -40, 120, degree_F
inTemp = 10, 120, degree_F
outHumidity = 0, 100
inHumidity = 0, 100
windSpeed = 0, 120, mile_per_hour
rain = 0, 10, inch
##############################################################################
# This section controls the origin of derived values.
[StdWXCalculate]
[[Calculations]]
# How to calculate derived quantities. Possible values are:
# hardware - use the value provided by hardware
# software - use the value calculated by weewx
# prefer_hardware - use value provide by hardware if available,
# otherwise use value calculated by weewx
pressure = prefer_hardware
altimeter = prefer_hardware
appTemp = prefer_hardware
barometer = prefer_hardware
cloudbase = prefer_hardware
dewpoint = prefer_hardware
ET = prefer_hardware
heatindex = prefer_hardware
humidex = prefer_hardware
inDewpoint = prefer_hardware
maxSolarRad = prefer_hardware
rainRate = prefer_hardware
windchill = prefer_hardware
windrun = prefer_hardware
##############################################################################
# For hardware that supports it, this section controls how often the
# onboard clock gets updated.
[StdTimeSynch]
# How often to check the weather station clock for drift (in seconds)
clock_check = 14400
# How much it can drift before we will correct it (in seconds)
max_drift = 5
##############################################################################
# This section is for configuring the archive service.
[StdArchive]
# If the station hardware supports data logging then the archive
interval
# will be downloaded from the station. Otherwise, specify it (in
seconds).
archive_interval = 300
# If possible, new archive records are downloaded from the station
# hardware. If the hardware does not support this, then new archive
# records will be generated in software.
# Set the following to "software" to force software record generation.
record_generation = hardware
# Whether to include LOOP data in hi/low statistics
loop_hilo = True
# The data binding used to save archive records
data_binding = wx_binding
# Whether to log successful archive operations
log_success = True
# Whether to log unsuccessful archive operations
log_failure = True
##############################################################################
# This section binds a data store to a database.
[DataBindings]
[[wx_binding]]
# The database must match one of the sections in [Databases].
# This is likely to be the only option you would want to change.
database = archive_mysql
# The name of the table within the database
table_name = archive
# The manager handles aggregation of data for historical summaries
manager = weewx.manager.DaySummaryManager
# The schema defines the structure of the database.
# It is *only* used when the database is created.
schema = schemas.wview_extended.schema
##############################################################################
# This section defines various databases.
[Databases]
# A SQLite database is simply a single file
[[archive_sqlite]]
database_name = weewx.sdb
database_type = SQLite
# MySQL
[[archive_mysql]]
database_name = weewx
database_type = MySQL
##############################################################################
# This section defines defaults for the different types of databases.
[DatabaseTypes]
# Defaults for SQLite databases
[[SQLite]]
driver = weedb.sqlite
# Directory in which the database files are located
SQLITE_ROOT = /var/lib/weewx
# Defaults for MySQL databases
[[MySQL]]
driver = weedb.mysql
# The host where the database is located
host = 192.168.1.17
# The user name for logging in to the host
user = XXX obfuscated by wee_debug XXX
# The password (use quotes to guard against parsing errors)
password = XXX obfuscated by wee_debug XXX
##############################################################################
# This section configures the internal weewx engine.
[Engine]
# The following section specifies which services should be run and in
what order.
[[Services]]
prep_services = weewx.engine.StdTimeSynch
data_services = ,
process_services = weewx.engine.StdConvert,
weewx.engine.StdCalibrate, weewx.engine.StdQC,
weewx.wxservices.StdWXCalculate
xtype_services = weewx.wxxtypes.StdWXXTypes,
weewx.wxxtypes.StdPressureCooker, weewx.wxxtypes.StdRainRater,
weewx.wxxtypes.StdDelta
archive_services = weewx.engine.StdArchive
restful_services = weewx.restx.StdStationRegistry,
weewx.restx.StdWunderground, weewx.restx.StdPWSweather,
weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS
report_services = weewx.engine.StdPrint, weewx.engine.StdReport
wee_debug report successfully generated
--
You received this message because you are subscribed to the Google Groups
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/weewx-user/fe01a8f9-417d-4a6a-937b-1944523c48b1n%40googlegroups.com.
weewx_log
Description: Binary data
