Thanks to all! Got a bit of work on my end to do... On Friday, February 12, 2021 at 5:33:31 PM UTC-6 tim lambert wrote:
> I didn’t even think about the SDR – mine worked out of the box, albeit > with the IP-100 extension from John Kline. > > > > Regards, > > > > Tim > > > > *From: *gjr80 > *Sent: *Friday, February 12, 2021 3:31 PM > *To: *weewx-user > *Subject: *Re: [weewx-user] Re: No data in mysql database & no html > reports. > > > > No, this is linux not windows. The issue is related to mapping of fields > within the sdr driver. Archive interval or database has nothing to do with > it, the driver is emitting no loop packets so WeeWX generates no archive > records, so nothing is saved to databases and consequently no reports are > run. > > > > I suggest working through the sdr setup again as per the sdr driver readme > <https://github.com/matthewwall/weewx-sdr>; running sdr directly, > determining the sensor map and working through the diagnosing of problems > section of the readme. If you can't make sense of what you are seeing post > the command(s) you enter and the exact response. > > > > Gary > > > > On Saturday, 13 February 2021 at 09:15:31 UTC+10 tim lambert wrote: > > Ed, > > > > I’m a bit perplexed…. > > > > 1. On line 3197 of the Log – the archive_interval is still showing > that it is set to 300 (looks like you didn’t save the weewx.conf change) > 2. On line 3226 of the Log – indicating an empty database (indicative > that the hooks between Python and MySQL aren’t installed) > 3. Consistently seeing - message repeated 3 times: [ DEBUG user.sdr: > lines=[]] -- I’m uncertain what is pushing these messages > 4. I’m not seeing where the Reports are being initiated – even with > the SeasonsSkin being enabled, and the Services defined/enabled in the > Engine look correct > > > > So this lends me to ask what platform are you working with and which > installation method did you follow? > > What version of Python is installed – you should be using Python3? > > > > Since you want to use MySQL, I’d suggest going down the route of > installing using setup.py method (http://www.weewx.com/docs/setup.htm) . > The pre-reqs should clear the path to getting everything installed to > generate the reports and populate the DB. > > > > Before I fired up MySQL, I allowed everything to run with SQLite (as > packaged) – the sdb files are in /weewx/archive. Once I saw data being > reported and verified data was being written to sdb, I then defined MySQL > Databases and user access, and modified weewx.conf (always back this up > before you make any changes, this way if you have a hiccup you can quickly > revert). > > > > Net-Net – my suggestion is to drop your current install and re-install > (ideally following the setup.py method. > > > > Feel free to ping me directly (off-thread) – if needed, we can have a > tele-conference and I can walk you through what I’ve done. > > > > Regards, > > > > Tim > > > > *From: *Ed Belcher > *Sent: *Friday, February 12, 2021 2:40 PM > *To: *weewx-user > *Subject: *Re: [weewx-user] Re: No data in mysql database & no html > reports. > > > > SELECT table_name, table_rows > > FROM INFORMATION_SCHEMA.TABLES > > WHERE TABLE_SCHEMA = 'weewx'; > > > > Returns a list of tables -- all with zero rows. > > > > On Friday, February 12, 2021 at 4:35:21 PM UTC-6 Ed Belcher wrote: > > Yes, debug is enabled. > > Linux thor 5.4.0-65-generic #73-Ubuntu SMP Mon Jan 18 17:25:17 UTC 2021 > x86_64 x86_64 x86_64 GNU/Linux > > > > Distributor ID: Ubuntu > > Description: Ubuntu 20.04.2 LTS > > Release: 20.04 > > Codename: focal > > > > As far as a tool goes, just using SQL queries against the tables. select > count(*) from table_name returns 0 rows. > > For web, ls -altr public_html/weewx from the command line. > > > > > > > > On Friday, February 12, 2021 at 4:12:16 PM UTC-6 tim lambert wrote: > > Ed, > > > > Can you email me the full log file – looking at a snipet is helpful? > > > > I’m looking to see if there is any attempt to connect and write to the DB > – I struggled a bit in this area too and would like to share my learnings > with you. > > > > I assume you have debug enabled. > > > > What is your platform/architecture? Are you running a tool like phpMyAdmin > – it’s an easy way to manage the MySQL DB? > > > > Regards, > > > > Tim > > > > *From: *Ed Belcher > *Sent: *Friday, February 12, 2021 2:04 PM > *To: *weewx-user > *Subject: *[weewx-user] Re: No data in mysql database & no html reports. > > > > Thanks for the reply, really appreciate the help. I changed the > archive_interval to 100 and restarted. Unfortunately, I got the same > results, even after waiting 30 minutes. From the log: > > Feb 12 15:31:51 DEBUG user.sdr: lines=['{"time" : "2021-02-12 21:31:48", > "model" : "Fineoffset-WH65B", "id" : 97, "battery_ok" : 1, "temperature_C" > : 2.000, "humidity" : 91, "wind_dir_deg" : 357, "wind_avg_m_s" : 0.765, > "wind_max_m_s" : 1.530, "rain_mm" : 3.810, "uv" : 57, "uvi" : 0, > "light_lux" : 7130.000, "mic" : "CRC"}\n'] > > Feb 12 16:01:11 DEBUG user.sdr: lines=['{"time" : "2021-02-12 22:01:08", > "model" : "Fineoffset-WH65B", "id" : 97, "battery_ok" : 1, "temperature_C" > : 1.500, "humidity" : 92, "wind_dir_deg" : 0, "wind_avg_m_s" : 1.530, > "wind_max_m_s" : 2.040, "rain_mm" : 3.810, "uv" : 33, "uvi" : 0, > "light_lux" : 3844.000, "mic" : "CRC"}\n'] > > > > Thanks > > Ed > > > > On Friday, February 12, 2021 at 2:55:29 PM UTC-6 tim lambert wrote: > > Ed, > > > > Your archive_interval (in StdArchive section) is set to 300 seconds (5 > minutes) -- meaning that data will be inserted into the DB every 5 > minutes. > > > > The log file simply shows that your weather station is being polled for > data regularly for data. You simply need to allow 5-10 minutes to pass > after starting weeWX, then you can look at your DB to verify data is being > written. > > > > The archive_interval also determines how often reports (aka skins) are > generated/published. By looking at your log files, you can determine how > long it takes for reports to generate -- based on that information you can > adjust your archive_interval to possibly write more often. > > > > Hope this helps. > > > > -- Tim > > > > On Friday, February 12, 2021 at 11:35:55 AM UTC-8 Ed Belcher wrote: > > I'm using the SDR driver for Ambient Weather WS-2902C "Fineoffset-WH65B" > on ubuntu 20.04. I am collecting data, but it does not insert into the > database and it does not generate html reports. I would appreciate any > advice. > > Thanks > > Ed > > > > ########################################################## > > log: > > INFO __main__: Initializing weewx version 4.4.0 > > INFO __main__: Using Python 3.9.0+ (default, Oct 20 2020, 08:43:38) > #012[GCC 9.3.0] > > INFO __main__: Platform Linux-5.4.0-65-generic-x86_64-with-glibc2.31 > > INFO __main__: Locale is 'en_US.UTF-8' > > INFO __main__: Using configuration file weewx.conf > > INFO __main__: Debug is 1 > > DEBUG __main__: Initializing engine > > INFO weewx.engine: Loading station type SDR (user.sdr) > > INFO user.sdr: driver version is 0.78 > > INFO user.sdr: sensor map is {'outTemp': > 'temperature.16.FOWH65BAltPacket', 'outHumidity': > 'humidity.16.FOWH65BAltPacket', 'windDir': 'wind_dir.16.FOWH65BAltPacket', > 'windSpeed': 'wind_speed.16.FOWH65BAltPacket', 'windGust': > 'wind_gust.16.FOWH65BAltPacket', 'rain_total': > 'rain_total.16.FOWH65BAltPacket', 'UV': 'uv_index.16.FOWH65BAltPacket', > 'outTempBatteryStatus': 'battery.16.FOWH65BAltPacket'} > > INFO user.sdr: deltas is {'rain': 'rain_total'} > > INFO user.sdr: startup process 'rtl_433 -M utc -F json -R 78 -f 914980000 > -s 250000' > > DEBUG user.sdr: start async reader for stdout-thread > > DEBUG user.sdr: start async reader for stderr-thread > > DEBUG weewx.engine: Loading service weewx.engine.StdTimeSynch > > DEBUG weewx.engine: Finished loading service weewx.engine.StdTimeSynch > > DEBUG weewx.engine: Loading service weewx.engine.StdConvert > > INFO weewx.engine: StdConvert target unit is 0x1 > > DEBUG weewx.engine: Finished loading service weewx.engine.StdConvert > > DEBUG weewx.engine: Loading service weewx.engine.StdCalibrate > > DEBUG weewx.engine: Finished loading service weewx.engine.StdCalibrate > > DEBUG weewx.engine: Loading service weewx.engine.StdQC > > DEBUG weewx.engine: Finished loading service weewx.engine.StdQC > > DEBUG weewx.engine: Loading service weewx.wxservices.StdWXCalculate > > DEBUG weewx.manager: Daily summary version is 4.0 > > DEBUG weewx.engine: Finished loading service > weewx.wxservices.StdWXCalculate > > DEBUG weewx.engine: Loading service weewx.wxxtypes.StdWXXTypes > > DEBUG weewx.engine: Finished loading service weewx.wxxtypes.StdWXXTypes > > DEBUG weewx.engine: Loading service weewx.wxxtypes.StdPressureCooker > > DEBUG weewx.engine: Finished loading service > weewx.wxxtypes.StdPressureCooker > > DEBUG weewx.engine: Loading service weewx.wxxtypes.StdRainRater > > DEBUG weewx.engine: Finished loading service weewx.wxxtypes.StdRainRater > > DEBUG weewx.engine: Loading service weewx.wxxtypes.StdDelta > > DEBUG weewx.engine: Finished loading service weewx.wxxtypes.StdDelta > > DEBUG weewx.engine: Loading service weewx.engine.StdArchive > > INFO weewx.engine: Archive will use data binding wx_binding > > INFO weewx.engine: Record generation will be attempted in 'software' > > INFO weewx.engine: Using archive interval of 300 seconds (software record > generation) > > DEBUG weewx.engine: Use LOOP data in hi/low calculations: 1 > > DEBUG weewx.engine: Finished loading service weewx.engine.StdArchive > > DEBUG weewx.engine: Loading service weewx.restx.StdStationRegistry > > INFO weewx.restx: StationRegistry: Registration not requested. > > DEBUG weewx.engine: Finished loading service weewx.restx.StdStationRegistry > > DEBUG weewx.engine: Loading service weewx.restx.StdWunderground > > INFO weewx.restx: Wunderground: Posting not enabled. > > DEBUG weewx.engine: Finished loading service weewx.restx.StdWunderground > > DEBUG weewx.engine: Loading service weewx.restx.StdPWSweather > > INFO weewx.restx: PWSweather: Posting not enabled. > > DEBUG weewx.engine: Finished loading service weewx.restx.StdPWSweather > > DEBUG weewx.engine: Loading service weewx.restx.StdCWOP > > INFO weewx.restx: CWOP: Posting not enabled. > > DEBUG weewx.engine: Finished loading service weewx.restx.StdCWOP > > DEBUG weewx.engine: Loading service weewx.restx.StdWOW > > INFO weewx.restx: WOW: Posting not enabled. > > DEBUG weewx.engine: Finished loading service weewx.restx.StdWOW > > DEBUG weewx.engine: Loading service weewx.restx.StdAWEKAS > > INFO weewx.restx: AWEKAS: Posting not enabled. > > DEBUG weewx.engine: Finished loading service weewx.restx.StdAWEKAS > > DEBUG weewx.engine: Loading service weewx.engine.StdPrint > > DEBUG weewx.engine: Finished loading service weewx.engine.StdPrint > > DEBUG weewx.engine: Loading service weewx.engine.StdReport > > DEBUG weewx.engine: Finished loading service weewx.engine.StdReport > > INFO __main__: Starting up weewx version 4.4.0 > > DEBUG weewx.engine: Station does not support reading the time > > INFO weewx.engine: Using binding 'wx_binding' to database 'weewx' > > INFO weewx.manager: Starting backfill of daily summaries > > INFO weewx.manager: Empty database > > INFO weewx.engine: Starting main packet loop. > > > > DEBUG user.sdr: lines=[] > > message repeated 3 times: [ DEBUG user.sdr: lines=[]] > > DEBUG user.sdr: lines=[] > > message repeated 8 times: [ DEBUG user.sdr: lines=[]] > > DEBUG user.sdr: lines=['{"time" : "2021-02-12 19:10:28", "model" : > "Fineoffset-WH65B", "id" : 97, "battery_ok" : 1, "temperature_C" : 2.000, > "humidity" : 93, "wind_dir_deg" : 17, "wind_avg_m_s" : 0.446, > "wind_max_m_s" : 0.510, "rain_mm" : 3.810, "uv" : 71, "uvi" : 0, > "light_lux" : 9005.000, "mic" : "CRC"}\n'] > > DEBUG user.sdr: lines=[] > > > > ####################################################### > > weewx.conf > > # WEEWX CONFIGURATION FILE > > # > > # Copyright (c) 2009-2021 Tom Keffer > > # See the file LICENSE.txt for your rights. > > > > > ############################################################################## > > > > # This section is for general configuration information. > > > > # Set to 1 for extra debug info, otherwise comment it out or set to zero > > debug = 1 > > > > # Root directory of the weewx data file hierarchy for this station > > WEEWX_ROOT = / > > > > # Whether to log successful operations > > log_success = True > > > > # Whether to log unsuccessful operations > > log_failure = True > > > > # How long to wait before timing out a socket (FTP, HTTP) connection > > socket_timeout = 20 > > > > # Do not modify this. It is used when installing and updating weewx. > > version = 4.4.0 > > > > > ############################################################################## > > > > # This section is for information about the station. > > > > [Station] > > > > # Description of the station location > > location = "XXXXXXXXXXXXXXXXXXXXXXXXXX" > > > > # Latitude in decimal degrees. Negative for southern hemisphere > > latitude = XXXXXXXXXXXXXXXXXX > > # Longitude in decimal degrees. Negative for western hemisphere. > > longitude = XXXXXXXXXXXXXXXXXXXXXX > > > > # Altitude of the station, with unit it is in. This is downloaded from > > # from the station if the hardware supports it. > > altitude = 141, foot > > > > # Set to type of station hardware. There must be a corresponding stanza > > # in this file with a 'driver' parameter indicating the driver to be > used. > > station_type = SDR > > > > # If you have a website, you may specify an URL > > #station_url = http://www.example.com > > > > # The start of the rain year (1=January; 10=October, etc.). This is > > # downloaded from the station if the hardware supports it. > > rain_year_start = 1 > > > > # Start of week (0=Monday, 6=Sunday) > > week_start = 6 > > > > > ############################################################################## > > > > [Interceptor] > > # This section is for the network traffic interceptor driver. > > > > # The driver to use: > > driver = user.interceptor > > > > # Specify the hardware device to capture. Options include: > > # acurite-bridge - acurite internet bridge, smarthub, or access > > # observer - fine offset WH2600/HP1000/HP1003, ambient WS2902 > > # lw30x - oregon scientific LW301/LW302 > > # lacrosse-bridge - lacrosse GW1000U/C84612 internet bridge > > # ecowitt-client - any hardware that uses the ecowitt protocol > > # wu-client - any hardware that uses the weather underground protocol > > device_type = observer > > port = 55 > > > > > ############################################################################## > > > > [Simulator] > > # This section is for the weewx weather station simulator > > > > # The time (in seconds) between LOOP packets. > > loop_interval = 2.5 > > > > # The simulator mode can be either 'simulator' or 'generator'. > > # Real-time simulator. Sleep between each LOOP packet. > > mode = simulator > > # Generator. Emit LOOP packets as fast as possible (useful for > testing). > > #mode = generator > > > > # The start time. Format is YYYY-mm-ddTHH:MM. If not specified, the > default > > # is to use the present time. > > #start = 2011-01-01T00:00 > > > > # The driver to use: > > driver = weewx.drivers.simulator > > > > > ############################################################################## > > > > [SDR] > > > > > > # This section is for the software-defined radio driver. > > > > # The time (in seconds) between LOOP packets. > > loop_interval = 2.5 > > > > # Direct testing command: > > # PYTHONPATH=/usr/share/weewx python /usr/share/weewx/user/sdr.py > --cmd="rtl_433 -M utc -F json -f 914980000 -s 250000" > > # Command probably needs a -p frequency offset parameter. > > > > # The driver to use > > driver = user.sdr > > path = /usr/share/weewx/user/ > > # ld_library_path = /usr/local/include > > cmd = rtl_433 -M utc -F json -R 78 -f 914980000 -s 250000 > > [[sensor_map]] > > outTemp = temperature.16.FOWH65BAltPacket > > outHumidity = humidity.16.FOWH65BAltPacket > > windDir = wind_dir.16.FOWH65BAltPacket > > windSpeed = wind_speed.16.FOWH65BAltPacket > > windGust = wind_gust.16.FOWH65BAltPacket > > rain_total = rain_total.16.FOWH65BAltPacket > > UV = uv_index.16.FOWH65BAltPacket > > # uv = uv.16.FOWH65BAltPacket # Not displaying in web page > > # light = light.16.FOWH65BAltPacket # Not displaying in web page > > outTempBatteryStatus = battery.16.FOWH65BAltPacket > > [[deltas]] > > rain = rain_total > > > > > ############################################################################## > > > > [FineOffsetUSB] > > # This section is for the Fine Offset series of weather stations. > > > > # The station model, e.g., WH1080, WS1090, WS2080, WH3081 > > model = WH2900 > > > > # How often to poll the station for data, in seconds > > polling_interval = 60 > > > > # The driver to use: > > driver = weewx.drivers.fousb > > > > > ############################################################################## > > > > # This section is for uploading data to Internet sites > > > > [StdRESTful] > > > > [[StationRegistry]] > > # To register this weather station with weewx, set this to true > > register_this_station = false > > > > [[AWEKAS]] > > # This section is for configuring posts to AWEKAS. > > > > # If you wish to do this, set the option 'enable' to true, > > # and specify a username and password. > > # To guard against parsing errors, put the password in quotes. > > enable = false > > username = replace_me > > password = replace_me > > > > [[CWOP]] > > # This section is for configuring posts to CWOP. > > > > # If you wish to do this, set the option 'enable' to true, > > # and specify the station ID (e.g., CW1234). > > enable = false > > station = replace_me > > > > # If this is an APRS (radio amateur) station, uncomment > > # the following and replace with a passcode (e.g., 12345). > > #passcode = replace_me (APRS stations only) > > > > [[PWSweather]] > > # This section is for configuring posts to PWSweather.com. > > > > # If you wish to do this, set the option 'enable' to true, > > # and specify a station and password. > > # To guard against parsing errors, put the password in quotes. > > enable = false > > station = replace_me > > password = replace_me > > > > [[WOW]] > > # This section is for configuring posts to WOW. > > > > # If you wish to do this, set the option 'enable' to true, > > # and specify a station and password. > > # To guard against parsing errors, put the password in quotes. > > enable = false > > station = replace_me > > password = replace_me > > > > [[Wunderground]] > > # This section is for configuring posts to the Weather Underground. > > > > # If you wish to do this, set the option 'enable' to true, > > # and specify a station (e.g., 'KORHOODR3') and password. > > # To guard against parsing errors, put the password in quotes. > > enable = false > > station = replace_me > > password = replace_me > > > > # If you plan on using wunderfixer, set the following > > # to your API key: > > api_key = replace_me > > > > # Set the following to True to have weewx use the WU "Rapidfire" > > # protocol. Not all hardware can support it. See the User's Guide. > > rapidfire = False > > > > > ############################################################################## > > > > # This section specifies what reports, using which skins, to generate. > > > > [StdReport] > > > > # Where the skins reside, relative to WEEWX_ROOT > > SKIN_ROOT = /etc/weewx/skins > > > > # Where the generated reports should go, relative to WEEWX_ROOT > > HTML_ROOT = /f1/https/weewx > > > > # The database binding indicates which data should be used in reports. > > data_binding = wx_binding > > > > # Whether to log a successful operation > > log_success = True > > > > # Whether to log an unsuccessful operation > > log_failure = True > > > > # Each of the following subsections defines a report that will be run. > > # See the customizing guide to change the units, plot types and line > > # colors, modify the fonts, display additional sensor data, and other > > # customizations. Many of those changes can be made here by overriding > > # parameters, or by modifying templates within the skin itself. > > > > [[SeasonsReport]] > > # The SeasonsReport uses the 'Seasons' skin, which contains the > > # images, templates and plots for the report. > > skin = Seasons > > enable = true > > > > [[SmartphoneReport]] > > # The SmartphoneReport uses the 'Smartphone' skin, and the images > and > > # files are placed in a dedicated subdirectory. > > skin = Smartphone > > enable = false > > HTML_ROOT = /f1/https/weewx/smartphone > > > > [[MobileReport]] > > # The MobileReport uses the 'Mobile' skin, and the images and files > > # are placed in a dedicated subdirectory. > > skin = Mobile > > enable = false > > HTML_ROOT = /f1/https/weewx/mobile > > > > [[StandardReport]] > > # This is the old "Standard" skin. By default, it is not enabled. > > skin = Standard > > enable = true > > # [[Belchertown]] > > # skin = Belchertown > > # HTML_ROOT = /f1/https/weewx/belchertown > > > > [[FTP]] > > # FTP'ing the results to a webserver is treated as just another > report, > > # albeit one with an unusual report generator! > > skin = Ftp > > > > # If you wish to use FTP, set "enable" to "true", then > > # fill out the next four lines. > > # Use quotes around passwords to guard against parsing errors. > > enable = false > > user = replace_me > > password = replace_me > > server = replace_me # The ftp server name, e.g, > www.myserver.org > > path = replace_me # The destination directory, e.g., /weather > > > > # Set to True for an FTP over TLS (FTPS) connection. Not all > servers > > # support this. > > secure_ftp = False > > > > # To upload files from something other than what HTML_ROOT is set > > # to above, specify a different HTML_ROOT here. > > HTML_ROOT = /f1/https/weewx > > > > # Most FTP servers use port 21 > > port = 21 > > > > # Set to 1 to use passive mode, zero for active mode > > passive = 1 > > > > [[RSYNC]] > > # rsync'ing to a webserver is treated as just another report > > skin = Rsync > > > > # If you wish to use rsync, you must configure passwordless ssh > using > > # public/private key authentication from the user account that > weewx > > # runs to the user account on the remote machine where the files > > # will be copied. > > # > > # If you wish to use rsync, set "enable" to "true", then > > # fill out server, user, and path. > > # The server should appear in your .ssh/config file. > > # The user is the username used in the identity file. > > # The path is the destination directory, such as > /var/www/html/weather. > > # Be sure that the user has write permissions on the destination! > > enable = false > > server = replace_me > > user = replace_me > > path = replace_me > > > > # To upload files from something other than what HTML_ROOT is set > > # to above, specify a different HTML_ROOT here. > > HTML_ROOT = /f1/https/weewx > > > > # Rsync can be configured to remove files from the remote server if > > # they don't exist under HTML_ROOT locally. USE WITH CAUTION: if > you > > # make a mistake in the remote path, you could could > unintentionally > > # cause unrelated files to be deleted. Set to 1 to enable remote > file > > # deletion, zero to allow files to accumulate remotely. > > delete = 0 > > > > #### > > > > # Various options for customizing your reports. > > > > [[Defaults]] > > > > [[[Units]]] > > > > # The following section sets what unit to use for each unit > group. > > # NB: The unit is always in the singular. I.e., > 'mile_per_hour', > > # NOT 'miles_per_hour' > > [[[[Groups]]]] > > > > group_altitude = foot # Options are 'foot' or 'meter' > > group_degree_day = degree_F_day # Options are > 'degree_F_day' or 'degree_C_day' > > group_distance = mile # Options are 'mile' or 'km' > > group_pressure = inHg # Options are 'inHg', 'mmHg', > 'mbar', 'hPa', or 'kPa' > > group_rain = inch # Options are 'inch', 'cm', or 'mm' > > group_rainrate = inch_per_hour # Options are > 'inch_per_hour', 'cm_per_hour', or 'mm_per_hour' > > group_speed = mile_per_hour # Options are > 'mile_per_hour', 'km_per_hour', 'knot', or 'meter_per_second' > > group_speed2 = mile_per_hour2 # Options are > 'mile_per_hour2', 'km_per_hour2', 'knot2', or 'meter_per_second2' > > group_temperature = degree_F # Options are 'degree_F' > or 'degree_C' > > > > # The following section sets the formatting for each type of > unit. > > [[[[StringFormats]]]] > > > > centibar = %.0f > > cm = %.2f > > cm_per_hour = %.2f > > degree_C = %.1f > > degree_F = %.1f > > degree_compass = %.0f > > foot = %.0f > > hPa = %.1f > > hour = %.1f > > inHg = %.3f > > inch = %.2f > > inch_per_hour = %.2f > > km = %.1f > > km_per_hour = %.0f > > km_per_hour2 = %.1f > > knot = %.0f > > knot2 = %.1f > > kPa = %.2f > > mbar = %.1f > > meter = %.0f > > meter_per_second = %.1f > > meter_per_second2 = %.1f > > mile = %.1f > > mile_per_hour = %.0f > > mile_per_hour2 = %.1f > > mm = %.1f > > mmHg = %.1f > > mm_per_hour = %.1f > > percent = %.0f > > second = %.0f > > uv_index = %.1f > > volt = %.1f > > watt_per_meter_squared = %.0f > > NONE = " N/A" > > > > # The following section overrides the label used for each type > of unit > > [[[[Labels]]]] > > > > meter = " meter", " meters" # You may prefer "metre". > > day = " day", " days" > > hour = " hour", " hours" > > minute = " minute", " minutes" > > second = " second", " seconds" > > NONE = "" > > > > # The following section sets the format for each time scale. > > # The values below will work in every locale, but they may not > look > > # particularly attractive. > > [[[[TimeFormats]]]] > > > > hour = %H:%M > > day = %X > > week = %X (%A) > > month = %x %X > > year = %x %X > > rainyear = %x %X > > current = %x %X > > ephem_day = %X > > ephem_year = %x %X > > > > [[[[Ordinates]]]] > > > > # Ordinal directions. The last one is for no wind direction > > directions = N, NNE, NE, ENE, E, ESE, SE, SSE, S, SSW, SW, > WSW, W, WNW, NW, NNW, N/A > > > > # The following section sets the base temperatures used for the > > # calculation of heating, cooling, and growing degree-days. > > [[[[DegreeDays]]]] > > > > # Base temperature for heating days, with unit: > > heating_base = 65, degree_F > > # Base temperature for cooling days, with unit: > > cooling_base = 65, degree_F > > # Base temperature for growing days, with unit: > > growing_base = 50, degree_F > > > > # A trend takes a difference across a time period. The > following > > # section sets the time period, and how big an error is > allowed to > > # still be counted as the start or end of a period. > > [[[[Trend]]]] > > > > time_delta = 10800 # 3 hours > > time_grace = 300 # 5 minutes > > > > # The labels to be used for each observation type > > [[[Labels]]] > > > > # Set to hemisphere abbreviations suitable for your location: > > hemispheres = N, S, E, W > > > > # Formats to be used for latitude whole degrees, longitude > whole > > # degrees, and minutes: > > latlon_formats = %02d, %03d, %05.2f > > > > # Generic labels, keyed by an observation type. > > [[[[Generic]]]] > > barometer = Barometer > > dewpoint = Dew Point > > ET = ET > > heatindex = Heat Index > > inHumidity = Inside Humidity > > inTemp = Inside Temperature > > outHumidity = Humidity > > outTemp = Outside Temperature > > radiation = Radiation > > rain = Rain > > rainRate = Rain Rate > > UV = UV Index > > windDir = Wind Direction > > windGust = Gust Speed > > windGustDir = Gust Direction > > windSpeed = Wind Speed > > windchill = Wind Chill > > windgustvec = Gust Vector > > windvec = Wind Vector > > extraTemp1 = Temperature1 > > extraTemp2 = Temperature2 > > extraTemp3 = Temperature3 > > > > # Sensor status indicators > > > > rxCheckPercent = Signal Quality > > txBatteryStatus = Transmitter Battery > > windBatteryStatus = Wind Battery > > rainBatteryStatus = Rain Battery > > outTempBatteryStatus = Outside Temperature Battery > > inTempBatteryStatus = Inside Temperature Battery > > consBatteryVoltage = Console Battery > > heatingVoltage = Heating Battery > > supplyVoltage = Supply Voltage > > referenceVoltage = Reference Voltage > > > > [[[Almanac]]] > > > > # The labels to be used for the phases of the moon: > > moon_phases = New, Waxing crescent, First quarter, Waxing > gibbous, Full, Waning gibbous, Last quarter, Waning crescent > > > > > ############################################################################## > > > > # This service acts as a filter, converting the unit system coming from > > # the hardware to a unit system in the database. > > > > [StdConvert] > > > > # The target_unit affects only the unit system in the database. Once > > # chosen it cannot be changed without converting the entire database. > > # Modification of target_unit after starting weewx will result in > > # corrupt data - the database will contain a mix of US and METRIC data. > > # > > # The value of target_unit does not affect the unit system for > > # reporting - reports can display US, Metric, or any combination of > units. > > # > > # In most cases, target_unit should be left as the default: US > > # > > # In particular, those migrating from a standard wview installation > > # should use US since that is what the wview database contains. > > > > # DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING! > > target_unit = US # Options are 'US', 'METRICWX', or 'METRIC' > > > > > ############################################################################## > > > > # This section can adjust data using calibration expressions. > > > > [StdCalibrate] > > > > [[Corrections]] > > # For each type, an arbitrary calibration expression can be given. > > # It should be in the units defined in the StdConvert section. > > # Example: > > foo = foo + 0.2 > > > > > ############################################################################## > > > > # This section is for quality control checks. If units are not specified, > > # values must be in the units defined in the StdConvert section. > > > > [StdQC] > > > > [[MinMax]] > > barometer = 26, 32.5, inHg > > pressure = 24, 34.5, inHg > > outTemp = -40, 120, degree_F > > inTemp = 10, 120, degree_F > > outHumidity = 0, 100 > > inHumidity = 0, 100 > > windSpeed = 0, 120, mile_per_hour > > rain = 0, 10, inch > > > > > ############################################################################## > > > > # This section controls the origin of derived values. > > > > [StdWXCalculate] > > > > [[Calculations]] > > # How to calculate derived quantities. Possible values are: > > # hardware - use the value provided by hardware > > # software - use the value calculated by weewx > > # prefer_hardware - use value provide by hardware if available, > > # otherwise use value calculated by weewx > > > > pressure = prefer_hardware > > altimeter = prefer_hardware > > appTemp = prefer_hardware > > barometer = prefer_hardware > > cloudbase = prefer_hardware > > dewpoint = prefer_hardware > > ET = prefer_hardware > > heatindex = prefer_hardware > > humidex = prefer_hardware > > inDewpoint = prefer_hardware > > maxSolarRad = prefer_hardware > > rainRate = prefer_hardware > > windchill = prefer_hardware > > windrun = prefer_hardware > > > > > ############################################################################## > > > > # For hardware that supports it, this section controls how often the > > # onboard clock gets updated. > > > > [StdTimeSynch] > > > > # How often to check the weather station clock for drift (in seconds) > > clock_check = 14400 > > > > # How much it can drift before we will correct it (in seconds) > > max_drift = 5 > > > > > ############################################################################## > > > > # This section is for configuring the archive service. > > > > [StdArchive] > > > > # If the station hardware supports data logging then the archive > interval > > # will be downloaded from the station. Otherwise, specify it (in > seconds). > > archive_interval = 300 > > > > # If possible, new archive records are downloaded from the station > > # hardware. If the hardware does not support this, then new archive > > # records will be generated in software. > > # Set the following to "software" to force software record generation. > > record_generation = software > > > > # Whether to include LOOP data in hi/low statistics > > loop_hilo = True > > > > # The data binding used to save archive records > > data_binding = wx_binding > > > > > ############################################################################## > > > > # This section binds a data store to a database. > > > > [DataBindings] > > > > [[wx_binding]] > > # The database must match one of the sections in [Databases]. > > # This is likely to be the only option you would want to change. > > database = archive_mysql > > # The name of the table within the database > > table_name = archive > > # The manager handles aggregation of data for historical summaries > > manager = weewx.manager.DaySummaryManager > > # The schema defines the structure of the database. > > # It is *only* used when the database is created. > > schema = schemas.wview_extended.schema > > > > > ############################################################################## > > > > # This section defines various databases. > > > > [Databases] > > > > # A SQLite database is simply a single file > > [[archive_sqlite]] > > database_name = weewx.sdb > > database_type = SQLite > > > > # MySQL > > [[archive_mysql]] > > database_name = weewx > > database_type = MySQL > > > > > ############################################################################## > > > > # This section defines defaults for the different types of databases. > > > > [DatabaseTypes] > > > > # Defaults for SQLite databases > > [[SQLite]] > > driver = weedb.sqlite > > # Directory in which the database files are located > > SQLITE_ROOT = /var/lib/weewx > > > > # Defaults for MySQL databases > > [[MySQL]] > > driver = weedb.mysql > > # The host where the database is located > > host = localhost > > # The user name for logging in to the host > > user = weewx > > # The password for the user name (quotes guard against parsing > errors) > > password = XXXXXXXXXXXX > > > > > ############################################################################## > > > > # This section configures the internal weewx engine. > > > > [Engine] > > > > # The following section specifies which services should be run and in > what order. > > [[Services]] > > prep_services = weewx.engine.StdTimeSynch > > data_services = , > > process_services = weewx.engine.StdConvert, > weewx.engine.StdCalibrate, weewx.engine.StdQC, > weewx.wxservices.StdWXCalculate > > xtype_services = weewx.wxxtypes.StdWXXTypes, > weewx.wxxtypes.StdPressureCooker, weewx.wxxtypes.StdRainRater, > weewx.wxxtypes.StdDelta > > archive_services = weewx.engine.StdArchive > > restful_services = weewx.restx.StdStationRegistry, > weewx.restx.StdWunderground, weewx.restx.StdPWSweather, > weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS > > report_services = weewx.engine.StdPrint, weewx.engine.StdReport > > > > > > -- > You received this message because you are subscribed to a topic in the > Google Groups "weewx-user" group. > To unsubscribe from this topic, visit > https://groups.google.com/d/topic/weewx-user/5a-qBZ0R01c/unsubscribe. > To unsubscribe from this group and all its topics, send an email to > [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/weewx-user/c3c1dfc9-8896-4b37-a919-31afb6b01452n%40googlegroups.com > > <https://groups.google.com/d/msgid/weewx-user/c3c1dfc9-8896-4b37-a919-31afb6b01452n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > > > -- > You received this message because you are subscribed to a topic in the > Google Groups "weewx-user" group. > To unsubscribe from this topic, visit > https://groups.google.com/d/topic/weewx-user/5a-qBZ0R01c/unsubscribe. > To unsubscribe from this group and all its topics, send an email to > [email protected]. > > To view this discussion on the web visit > https://groups.google.com/d/msgid/weewx-user/c9796823-adf4-444a-a953-5295928f84b9n%40googlegroups.com > > <https://groups.google.com/d/msgid/weewx-user/c9796823-adf4-444a-a953-5295928f84b9n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > > > -- > You received this message because you are subscribed to a topic in the > Google Groups "weewx-user" group. > To unsubscribe from this topic, visit > https://groups.google.com/d/topic/weewx-user/5a-qBZ0R01c/unsubscribe. > To unsubscribe from this group and all its topics, send an email to > [email protected]. > > To view this discussion on the web visit > https://groups.google.com/d/msgid/weewx-user/3364aca5-53bd-4b4f-a719-49744674b094n%40googlegroups.com > > <https://groups.google.com/d/msgid/weewx-user/3364aca5-53bd-4b4f-a719-49744674b094n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > > -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/d641911e-48d9-49dc-8aa3-5c2f61dc039bn%40googlegroups.com.
