Hi I do have data in all fields and it is being displayed in weekly, monthly and yearly graphs.
On day 1 I lost outHumidity and since then I have lost all other DAILY graphs except rain and wind vector. Weekly still correct and up-to date I sort of suspect some sort of 'units' issue as I rebuilt the conf file during the conversion but I don't understand how the weekly graph would still be ok and up to date. The Units displaying in daily and weekly graphs are the same. Many thanks for your help Paul On Thursday, 11 May 2017 17:13:49 UTC+1, Andrew Milner wrote: > > what data do you have in the inHumidity and outHumidity fields in the > database??? Note the caps in .conf are also required. > > On Thursday, 11 May 2017 15:25:14 UTC+3, Paul Carpenter wrote: >> >> I also rebuilt a new SD card (for a Pi) to transfer from Wheezy to Jessie >> and used apt-get to install Weewx 3.7.1 (from 3.6.2 if I remember correctly) >> >> I do have dayhumidity.png in the html pages but it is not populated with >> data. >> >> I do have the lines (shown by Tom above) in the skin.conf file for Day, >> Week, Month and Year >> >> Also have the Weekly , Monthly and Yearly png files and these are all >> populated and up to date. >> >> Any ideas appreciated >> >> Paul >> >> >> On Wednesday, 3 May 2017 09:05:55 UTC+1, Nick Mason wrote: >>> >>> Tom, >>> >>> thank you, those two lines of code were missing from skin.conf and from >>> the backup. >>> >>> Just to prove I wasn't going mad I put the original SD card back in the >>> RPi and they are there! >>> >>> I also had to add the code to the monthly and yearly sections, modified >>> accordingly. >>> >>> How they got removed from the backup I have no idea, it seems too >>> specific for corruption during the backup but stranger things have happened >>> >>> Regards >>> Nick >>> >>> On Tuesday, 2 May 2017 22:55:35 UTC+1, Tom Keffer wrote: >>>> >>>> If other images are being generated, but only the dayhumidity.png image >>>> is missing, the problem must be in the skin.conf file. If you did a Debian >>>> install, it will be located in /etc/weewx/skins/Standard/skin.conf >>>> >>>> The relevant section should look something like this: >>>> >>>> >>>> ... >>>> [[[daytempchill]]] >>>> [[[[windchill]]]] >>>> [[[[heatindex]]]] >>>> >>>> [[[dayhumidity]]] >>>> [[[[outHumidity]]]] >>>> >>>> [[[dayrain]]] >>>> # Make sure the y-axis increment is at least 0.02 for the >>>> rain plot >>>> yscale = None, None, 0.02 >>>> plot_type = bar >>>> [[[[rain]]]] >>>> aggregate_type = sum >>>> aggregate_interval = 3600 >>>> label = Rain (hourly total) >>>> ... >>>> >>>> >>>> >>>> On Tue, May 2, 2017 at 9:57 AM, Nick Mason <[email protected]> wrote: >>>> >>>>> I've had a small but nagging problem for a while with my Raspberry Pi >>>>> that runs weewx. When I try to upgrade rasbian I get an error message. >>>>> >>>>> I'm not sure if I get a partial upgrade or no upgrade following a; >>>>> >>>>> sudo apt-get update >>>>> sudo apt-get upgrade >>>>> >>>>> I finally got around to sorting it out by by creating a new MicroSD >>>>> card with the latest rasbian image. I then decide that along with the >>>>> latest OS that I'd do a fresh install of weewx as well and this time >>>>> rather >>>>> than do a manual download and install using setup.py I would install >>>>> weewx >>>>> via apt-get install weewx. >>>>> >>>>> All went well, it's a lot easier than the manual method and it worked >>>>> as advertised. I then replaced the new database with the one from my >>>>> backup >>>>> and weewx dutifully brought it up to date. However, I noticed that the >>>>> graphs on the web page were staggered and out of alignment and that this >>>>> was because one of the graphs, Outside Humidity, is missing. All that >>>>> shows >>>>> is a small box with 'outside humidity' in it. >>>>> >>>>> I've had a look through the code and what should be displayed is the >>>>> dayhumidity.png image. This image isn't being generated and does not >>>>> appear >>>>> in /var/www/html/weewx >>>>> >>>>> I've compared the new weewx.conf and skin.conf files with the backups >>>>> I have from the older version and they look the same. >>>>> >>>>> Can someone point me at where the report is generated and the image >>>>> file produced please so I can have a look at what's going on. >>>>> >>>>> Thanks >>>>> Nick >>>>> >>>>> -- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "weewx-user" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send >>>>> an email to [email protected]. >>>>> For more options, visit https://groups.google.com/d/optout. >>>>> >>>> >>>> -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
