found a article about this,
http://www.motobit.com/help/scptutl/pa98.htm
it's the limit applied on browser lol
so if you use FireFox with HttpFox you can see the post sends nothing
if file bigger than 2GB
On Oct 22, 5:24 pm, AndCycle <andcycle-goo...@andcycle.idv.tw> wrote:
> ok, Richard, are you trying to upload a really big file that over 2GB?
> try smaller one like 100MB,
> I am investigating where is the limit
>
> AndCycle wrote:
> > oops, there must be something breaked, I can't it work too,
>
> > I will reply after fix it, sorry :(
>
> > Richard wrote:
> > > I got the same problem with the example from AndCycle, using the
> > > builtin web2py server.
> > > Can anyone else get it working? If so what setup do you have?
>
> > > Richard
>
> > > On Oct 20, 3:40 pm, Richard <richar...@gmail.com> wrote:
> > > > No, nothing is uploaded. Theprogressbar shows NaN (divide by zero
> > > > error), then the page submits but the file is not uploaded.
>
> > > > I'll check the uploaded example - thanks for that.
> > > > Richard
>
> > > > On Oct 20, 6:32 am, mdipierro <mdipie...@cs.depaul.edu> wrote:
>
> > > > > doesuploadwork? This assumes cache.ram is working so it would not
> > > > > work with CGI.
>
> > > > > Massimo
>
> > > > > On Oct 18, 8:02 pm, Richard <richar...@gmail.com> wrote:
>
> > > > > > thanks for putting that together!
> > > > > > I tried it out with latest trunk but found that the returned json
> > > > > > was
> > > > > > always {'length':0, 'uploaded':0}
> > > > > > Any ideas? I didn't change anything.
>
> > > > > > In case it matters I am using the builtin web2py server with sqlite
> > > > > > on
> > > > > > Ubuntu 9.04.
>
> > > > > > Also is post.json necessary? It will use generic.json by default.
>
> > > > > > Richard
>
> > > > > > On Oct 17, 3:59 am, AndCycle <andcycle-goo...@andcycle.idv.tw>
> > > > > > wrote:
>
> > > > > > >http://www.web2pyslices.com/main/slices/take_slice/10
>
> > > > > > > anyway, I have done the sample, any comment? :~
>
> > > > > > > On Oct 16, 11:39 pm, AndCycle <andcycle-goo...@andcycle.idv.tw>
> > > > > > > wrote:
>
> > > > > > > > would you? :p
>
> > > > > > > > On Oct 15, 2:03 pm, mdipierro <mdipie...@cs.depaul.edu> wrote:
>
> > > > > > > > > yes. Thank you! We should post a web2pyslice about this.
>
> > > > > > > > > On Oct 14, 11:50 pm, Richard <richar...@gmail.com> wrote:
>
> > > > > > > > > > is this it?http://pastebin.com/f69e7b008
>
> > > > > > > > > > On Oct 15, 11:55 am, mdipierro <mdipie...@cs.depaul.edu>
> > > > > > > > > > wrote:
>
> > > > > > > > > > > I remember the author of the patch posted an example but
> > > > > > > > > > > I cannot find
> > > > > > > > > > > it. I hope he will step in and point us to it.
>
> > > > > > > > > > > Massimo
>
> > > > > > > > > > > On Oct 14, 7:43 pm, Richard <richar...@gmail.com> wrote:
>
> > > > > > > > > > > > hello,
>
> > > > > > > > > > > > I noticed copystream_progress() in trunk. Is there an
> > > > > > > > > > > > example how to
> > > > > > > > > > > > use it?
> > > > > > > > > > > > Richard
>
> > > > > > > > > > > > On Oct 11, 6:43 am, mdipierro <mdipie...@cs.depaul.edu>
> > > > > > > > > > > > wrote:
>
> > > > > > > > > > > > > @AndCycle
>
> > > > > > > > > > > > > I rearranged the code in trunk a bit. Could you check
> > > > > > > > > > > > > it still works?
> > > > > > > > > > > > > Thanks again.
>
> > > > > > > > > > > > > Massimo
>
> > > > > > > > > > > > > On Oct 8, 5:14 am, AndCycle
> > > > > > > > > > > > > <andcycle-goo...@andcycle.idv.tw> wrote:
>
> > > > > > > > > > > > > > thanks :)
>
> > > > > > > > > > > > > > I will take some free time to write a example base
> > > > > > > > > > > > > > on trunk :p
>
> > > > > > > > > > > > > > On Oct 7, 10:24 pm, mdipierro
> > > > > > > > > > > > > > <mdipie...@cs.depaul.edu> wrote:
>
> > > > > > > > > > > > > > > Check again. I added it now.
>
> > > > > > > > > > > > > > > On Oct 7, 6:42 am, AndCycle
> > > > > > > > > > > > > > > <andcycle-goo...@andcycle.idv.tw> wrote:
>
> > > > > > > > > > > > > > > > oops, the patch been cut by width restriction
> > > > > > > > > > > > > > > > on mailing list lol
>
> > > > > > > > > > > > > > > > here is pastebinhttp://pastebin.com/f219d603b
--~--~---------~--~----~------------~-------~--~----~
You received this message because you are subscribed to the Google Groups
"web2py-users" group.
To post to this group, send email to web2py@googlegroups.com
To unsubscribe from this group, send email to
web2py+unsubscr...@googlegroups.com
For more options, visit this group at
http://groups.google.com/group/web2py?hl=en
-~----------~----~----~----~------~----~------~--~---
