I got the same problem with the example from AndCycle, using the
builtin web2py server.
Can anyone else get it working? If so what setup do you have?
Richard
On Oct 20, 3:40 pm, Richard <richar...@gmail.com> wrote:
> No, nothing is uploaded. Theprogressbar shows NaN (divide by zero
> error), then the page submits but the file is not uploaded.
>
> I'll check the uploaded example - thanks for that.
> Richard
>
> On Oct 20, 6:32 am, mdipierro <mdipie...@cs.depaul.edu> wrote:
>
> > doesuploadwork? This assumes cache.ram is working so it would not
> > work with CGI.
>
> > Massimo
>
> > On Oct 18, 8:02 pm, Richard <richar...@gmail.com> wrote:
>
> > > thanks for putting that together!
> > > I tried it out with latest trunk but found that the returned json was
> > > always {'length':0, 'uploaded':0}
> > > Any ideas? I didn't change anything.
>
> > > In case it matters I am using the builtin web2py server with sqlite on
> > > Ubuntu 9.04.
>
> > > Also is post.json necessary? It will use generic.json by default.
>
> > > Richard
>
> > > On Oct 17, 3:59 am, AndCycle <andcycle-goo...@andcycle.idv.tw> wrote:
>
> > > >http://www.web2pyslices.com/main/slices/take_slice/10
>
> > > > anyway, I have done the sample, any comment? :~
>
> > > > On Oct 16, 11:39 pm, AndCycle <andcycle-goo...@andcycle.idv.tw> wrote:
>
> > > > > would you? :p
>
> > > > > On Oct 15, 2:03 pm, mdipierro <mdipie...@cs.depaul.edu> wrote:
>
> > > > > > yes. Thank you! We should post a web2pyslice about this.
>
> > > > > > On Oct 14, 11:50 pm, Richard <richar...@gmail.com> wrote:
>
> > > > > > > is this it?http://pastebin.com/f69e7b008
>
> > > > > > > On Oct 15, 11:55 am, mdipierro <mdipie...@cs.depaul.edu> wrote:
>
> > > > > > > > I remember the author of the patch posted an example but I
> > > > > > > > cannot find
> > > > > > > > it. I hope he will step in and point us to it.
>
> > > > > > > > Massimo
>
> > > > > > > > On Oct 14, 7:43 pm, Richard <richar...@gmail.com> wrote:
>
> > > > > > > > > hello,
>
> > > > > > > > > I noticed copystream_progress() in trunk. Is there an example
> > > > > > > > > how to
> > > > > > > > > use it?
> > > > > > > > > Richard
>
> > > > > > > > > On Oct 11, 6:43 am, mdipierro <mdipie...@cs.depaul.edu> wrote:
>
> > > > > > > > > > @AndCycle
>
> > > > > > > > > > I rearranged the code in trunk a bit. Could you check it
> > > > > > > > > > still works?
> > > > > > > > > > Thanks again.
>
> > > > > > > > > > Massimo
>
> > > > > > > > > > On Oct 8, 5:14 am, AndCycle
> > > > > > > > > > <andcycle-goo...@andcycle.idv.tw> wrote:
>
> > > > > > > > > > > thanks :)
>
> > > > > > > > > > > I will take some free time to write a example base on
> > > > > > > > > > > trunk :p
>
> > > > > > > > > > > On Oct 7, 10:24 pm, mdipierro <mdipie...@cs.depaul.edu>
> > > > > > > > > > > wrote:
>
> > > > > > > > > > > > Check again. I added it now.
>
> > > > > > > > > > > > On Oct 7, 6:42 am, AndCycle
> > > > > > > > > > > > <andcycle-goo...@andcycle.idv.tw> wrote:
>
> > > > > > > > > > > > > oops, the patch been cut by width restriction on
> > > > > > > > > > > > > mailing list lol
>
> > > > > > > > > > > > > here is pastebinhttp://pastebin.com/f219d603b
>
>
--~--~---------~--~----~------------~-------~--~----~
You received this message because you are subscribed to the Google Groups
"web2py-users" group.
To post to this group, send email to web2py@googlegroups.com
To unsubscribe from this group, send email to
web2py+unsubscr...@googlegroups.com
For more options, visit this group at
http://groups.google.com/group/web2py?hl=en
-~----------~----~----~----~------~----~------~--~---
