The 10 MHz ref supplied to each X310 device is used in a PLL in each device
to obtain the 10MHz ref used for that device (and for disciplining the
various LOs on the device). Thus, there is a relative phase "wobble"
between the 10MHz ref signals used on each device as each PLL continuously
adjusts to maintain disciplined output. Over time, this averages out to
zero. But, instantaneously, it is not. So, my question is: how
instantaneous is your phase measurement? If you instead calculate a phase
averaged over numerous samples, can you get a consistent result? From your
plot, it looks like this is true.
Rob
On Wed, May 1, 2024 at 11:04 AM zhou via USRP-users <
usrp-users@lists.ettus.com> wrote:
>
>
> On Wednesday, 1 May 2024 at 15:15:12 BST, Marcus D. Leech <
> patchvonbr...@gmail.com> wrote:
>
>
> On 01/05/2024 10:11, zhou via USRP-users wrote:
>
> Hi Marcus,
>
> Thanks for your response.
>
> "Are you setting up clocking identically for both USRPs? That is setting
> the reference clock to "external" and the 1PPS source to "external" on both
> devices? Are you using a single multi_usrp object for all RX channels?"
>
> Yes, I use multi_usrp multi_usrp::make(
> 'addr0=192.168.12.2,second_addr0=192.168.13.2,addr1=192.168.14.2,second_addr1=192.168.15.2,master_clock_rate=184.32e6'
> )
>
> "external" set for both ref and pps:
> usrp->set_clock_source("external")
> usrp->set_time_source("external")
> I think this should automatically set both devices.
>
> "What type of daughtercards are in your X310?"
> UBX
>
> Kind regards.
>
> And, to clarify, this is an Octoclock-G, and not a plain Octoclock ?
>
> It is OctoClock GPSDO, and Internal is used.
>
>
>
>
> On Wednesday, 1 May 2024 at 14:19:44 BST, Marcus D. Leech
> <patchvonbr...@gmail.com> <patchvonbr...@gmail.com> wrote:
>
>
> On 01/05/2024 08:25, zhou via USRP-users wrote:
>
> Hi All,
>
> I am trying to use 4Rx and 4Tx antennas from two X310 USRPs. I hope the
> received signals have stable phase relationship but they don't seem to be.
> I am wondering why and how to fix it.
>
> I measured the phase using the connection as below:
> [image: Inline image]
> cos(t)+i*sin(t) signal is split into and received on four Rx antennas. Two
> X310s are connected to the same OctoClock for 10MHz Ref and PPS. Tx and Rx
> commands are all timed. The measurement results are as below:
>
>
> The Tx signal is continuous during test. I measured phase every second for
> 20 sec. In the 2nd USRP, the phases are stable on both antennas while it is
> not in the 1st. If I change the Tx signal to the 1st USRP, then the results
> swap - phases become stable in the 1st USRP and unstable in the 2nd.
>
> My first though was that there might be small CFO between USRPs even
> though both are connected to the OctoClock, but CFO should have caused
> linear change. Here, the phase offset is not linear and kind of random
> within 20 second measurement.
>
> What can be the reason? Any suggestion will be appreciated.
>
> Kind regards,
> H.
> Are you setting up clocking identically for both USRPs? That is setting
> the reference clock to "external" and the 1PPS source to "external" on both
> devices? Are you using a single multi_usrp object for all RX channels?
>
> What type of daughtercards are in your X310?
>
>
> _______________________________________________
> USRP-users mailing list -- usrp-users@lists.ettus.com
> To unsubscribe send an email to usrp-users-le...@lists.ettus.com
>
> _______________________________________________
> USRP-users mailing list -- usrp-users@lists.ettus.com
> To unsubscribe send an email to usrp-users-le...@lists.ettus.com
>
>
> _______________________________________________
> USRP-users mailing list -- usrp-users@lists.ettus.com
> To unsubscribe send an email to usrp-users-le...@lists.ettus.com
> _______________________________________________
> USRP-users mailing list -- usrp-users@lists.ettus.com
> To unsubscribe send an email to usrp-users-le...@lists.ettus.com
>
_______________________________________________
USRP-users mailing list -- usrp-users@lists.ettus.com
To unsubscribe send an email to usrp-users-le...@lists.ettus.com
