But it should. This is basic functionality that is completely broken. The commit to fix it is simple.
On Fri, Feb 9, 2024 at 10:06 AM Marcus D. Leech <patchvonbr...@gmail.com> wrote: > On 09/02/2024 09:07, Rob Kossler via USRP-users wrote: > > This is fixed in 4.5 and 4.6. Are you able to switch? > Rob > > I'll add that it's unlikely for the fix to get back-ported to 4.4 at this > point. > > > > > On Fri, Feb 9, 2024 at 5:04 AM <sp...@hs-bremen.de> wrote: > >> Hi, >> >> I am facing the same problem. >> >> I am on a Linux machine and hardware is an X300 with a UBX160. >> >> When I am above 500 MHz the actual carrier freq becomes about 2000 MHz >> smaller. >> >> I checked it with the uhd example script tx_waveforms that comes with >> the uhd install. Below is the output. Note that actual frequency is >> negative. There is no output at 915 MHz on a spectrum analyzer. Below 500 >> MHz everything is fine. >> >> Same happens when using Gnuradio. >> >> Thanks >> >> Soren >> >> >> ------------------------------ >> >> $ ./tx_waveforms --freq 915e6 --rate 5e6 --gain 0 >> >> Creating the usrp device with: ... >> [INFO] [UHD] linux; GNU C++ version 13.1.0; Boost_107400; >> UHD_4.4.0.0+ds1-4 >> [INFO] [X300] X300 initialization sequence... >> [INFO] [X300] Maximum frame size: 1472 bytes. >> [INFO] [X300] Radio 1x clock: 200 MHz >> Using Device: Single USRP: >> Device: X-Series Device >> Mboard 0: X300 >> RX Channel: 0 >> RX DSP: 0 >> RX Dboard: A >> RX Subdev: UBX RX >> RX Channel: 1 >> RX DSP: 1 >> RX Dboard: B >> RX Subdev: Unknown (0xffff) - 0 >> TX Channel: 0 >> TX DSP: 0 >> TX Dboard: A >> TX Subdev: UBX TX >> TX Channel: 1 >> TX DSP: 1 >> TX Dboard: B >> TX Subdev: Unknown (0xffff) - 0 >> >> Setting TX Rate: 5.000000 Msps... >> Actual TX Rate: 5.000000 Msps... >> >> Setting TX Freq: 915.000000 MHz... >> Setting TX LO Offset: 0.000000 MHz... >> Actual TX Freq: -1085.000002 MHz... >> >> Setting TX Gain: 0.000000 dB... >> Actual TX Gain: 0.000000 dB... >> >> [WARNING] [0/Radio#0] Attempting to set tick rate to 0. Skipping. >> Setting device timestamp to 0... >> Checking TX: TXLO: locked ... >> Press Ctrl + C to stop streaming... >> _______________________________________________ >> USRP-users mailing list -- usrp-users@lists.ettus.com >> To unsubscribe send an email to usrp-users-le...@lists.ettus.com >> > > _______________________________________________ > USRP-users mailing list -- usrp-users@lists.ettus.com > To unsubscribe send an email to usrp-users-le...@lists.ettus.com > > > _______________________________________________ > USRP-users mailing list -- usrp-users@lists.ettus.com > To unsubscribe send an email to usrp-users-le...@lists.ettus.com >
_______________________________________________ USRP-users mailing list -- usrp-users@lists.ettus.com To unsubscribe send an email to usrp-users-le...@lists.ettus.com
