Hi Vladica, >From the 'changelog', it appears that N321 support began with release 3.14. But, at that point I believe that WR was already broken. So, I think that there is no solution to your problem other than to wait for Ettus to fix the WR issues. However, WR has been broken for a while (note user-list posts from last fall Sept & Dec) so I don't know when this will be working again. Rob
On Wed, Jul 7, 2021 at 10:26 AM Vladica Sark <vladicas...@gmail.com> wrote: > Hi Michael, > > I obtained the necessary SFP+ optical adapters and now I am trying to > put uhd 3.13.1.0 on the N321s in order to use the WR synchronization. > Unfortunately, when I update the sd card image with 3.13.1.0 the N321 > boots but the SFP0 and SFP1 do not go up. When I try to run > uhd_find_devices, on a terminal using the USB port it says no UHD > devices are found. > > I believe that the right FPGA image should be put on the FPGA, but the > ways described in Knowledgebase are not working. > > Is there a way to put the version 3.13.1.0 on the N321? I have tried > version 4.0.0.0 and it is working fine, but WR is broken. > > BR, > Vladica > > > On 22.06.21 21:31, Michael Dickens wrote: > > I'm using primarily FS adapters, cables (single and multi mode), and > > fiber connectors (to allow multiplexing lanes). The adapters I bought > > were "generic" and had to be tweaked using an FS BOX to be fully > > compatible with Intel or Mellanox NICs. This tweaking seems to have > > helped a lot with the 100 Gb interface (E810); the 10 Gb interfaces do > > not show much benefit to be manufacturer specific -- though I'm sure > > it doesn't hurt! I have not tried a multi-mode to single mode splitter > > / joiner, but I'd suppose they do exist & if anybody here has had > > experience that would be useful to hear about! I hope this is useful! > > - MLD > > > > > > On Tue, Jun 22, 2021 at 10:05 AM Vladica Sark <vladicas...@gmail.com > > <mailto:vladicas...@gmail.com>> wrote: > > > > Hi Michael, > > > > Thanks for the answer. For now for the data I am using DAC cables, > > but > > we would need larger distances, i.e. 50+ meters, and for this I would > > need fibers for both WR and data. > > > > Is there also some optical multiplexer for these wavelengths, in > > order > > to use a simplex fiber, for both WR and data? > > > > BR, > > Vladica > > > > On 22.06.21 15:41, Michael Dickens wrote: > > > Hi Vladica - I've tested a variety of fiber adapters and cables > > with > > > no issues (e.g., ZyXEL, FS, Axcen). The primary keys are to make > > sure > > > the various related parameters match up between the adapters and > > > cables and devices. For example: If the adapter is 1490/1310, > > then you > > > want to make sure the cable is for the same wavelengths. Same > > for the > > > fiber polish and other parameters (single / dual fiber ; . Some are > > > easier than others, none of this is too difficult luckily! > > > > > > For short distances, a DAC cable will work for all of the N320/N321 > > > SFP interfaces. > > > > > > At the moment, WR support is being fixed for UHD 3.14.0.0 to > > current. > > > If you -require- WR support -right now- you can use UHD 3.13.1.0 > > while > > > we're working out how to fix WR for newer UHD. We expect the fix > > to be > > > available to customers sometime in mid/late-July (2021); once > > the fix > > > is determined and verified we will commit it to the various > > branches > > > of the UHD repository, and it will be available in UHD -after- the > > > forthcoming 4.1 release. It will be available in the public UHD > > > repository for folks to use to patch UHD between releases. > > > > > > I hope this is useful! - MLD > > > > > > > > > On Tue, Jun 22, 2021 at 6:19 AM Vladica Sark > > <vladicas...@gmail.com <mailto:vladicas...@gmail.com> > > > <mailto:vladicas...@gmail.com <mailto:vladicas...@gmail.com>>> > > wrote: > > > > > > Dear all, > > > > > > I would like to use N321 with WRS 3/18 which uses optical > > cables. I > > > would like to use also for the 10 Gbit SFP1 optical SFP+ > > transceiver. > > > Do you have some recommended optical SFP+ adapters, duplex and, > > > preferably, simplex? > > > The idea is to use a duplex monomode fiber, one fiber for > > the 10 Gbit > > > data and one fiber for WRS synchronization. > > > They would be connected to 10 Gbit switch or QNAP > > Thunderbolt to SFP+ > > > adapter, so they do not have to be Intel. > > > > > > > > > Best regards, > > > > > > Vladica > > > > > > _______________________________________________ > > > USRP-users mailing list -- usrp-users@lists.ettus.com > > <mailto:usrp-users@lists.ettus.com> > > > <mailto:usrp-users@lists.ettus.com > > <mailto:usrp-users@lists.ettus.com>> > > > To unsubscribe send an email to > > usrp-users-le...@lists.ettus.com > > <mailto:usrp-users-le...@lists.ettus.com> > > > <mailto:usrp-users-le...@lists.ettus.com > > <mailto:usrp-users-le...@lists.ettus.com>> > > > > > > _______________________________________________ > USRP-users mailing list -- usrp-users@lists.ettus.com > To unsubscribe send an email to usrp-users-le...@lists.ettus.com >
_______________________________________________ USRP-users mailing list -- usrp-users@lists.ettus.com To unsubscribe send an email to usrp-users-le...@lists.ettus.com
