Hi Julián - I'm working on this issue for Ettus. I'll bring you into a discussion off list; once we get a resolution we can post back here. - MLD
On Thu, May 6, 2021 at 1:54 PM Burella Pérez Julián Mariano < julian.burellape...@heig-vd.ch> wrote: > Hi Rob, > > Thank you for your feedback ! > > I am relieved to learn that I'm not the only user experience issues using > WR with N32x boards. > Where did you find out that Ettus is presently looking into WR issues ? > I'm asking because I can see a different thread from 2019 ( > http://ettus.80997.x6.nabble.com/USRP-users-N320-XQ-image-issue-using-sfp0-as-time-source-td13973.html > ) > Which as far as I can see, no fix is implemented in uhd:master. > > BTW, I work with uhd4.0 - commit cf570707a2. > We tried 2 different N320 boards, both resulted in the same behavior. > > Best, > > Julián > > =================================== > Julián Mariano Burella Pérez > M.Sc.Eng. TIN, Embedded Systems > Collaborateur Ra&D HES > Prof.: +41 24 557 62 84 > julian.burellape...@heig-vd.ch<mailto:julian.burellape...@heig-vd.ch> > Haute École d'Ingénierie et de Gestion du Canton de Vaud > Route de Cheseaux 1 - CP 521 - 1401 Yverdon-les-Bains > =================================== > ________________________________ > De : Rob Kossler <rkoss...@nd.edu> > Envoyé : jeudi, 6 mai 2021 15:41:11 > À : Burella Pérez Julián Mariano > Cc : usrp-users@lists.ettus.com > Objet : Re: [USRP-users] [N320] Using white rabbit with OPNT Master Switch > > Hi Julián, > I am also getting these same errors and have been unsuccessful getting WR > working on either 3.15 or 4.0. I have asked this list to see if anyone is > presently using WR successfully, but have not had any replies. I know that > Ettus is presently looking into WR issues. > Rob > > > On Thu, May 6, 2021 at 8:57 AM Burella Pérez Julián Mariano < > julian.burellape...@heig-vd.ch<mailto:julian.burellape...@heig-vd.ch>> > wrote: > Hello, > > We have a setup where we're trying to sync a N320 (bitstream WX) using > White rabbit with a OPNT Timing Switch as Master configured as Free Running > Master. > > > +------------------------+ +---------------------+ > | | SFP0 | > | > | OPNT Timing Switch |---------------- | N320 | > | | | > | > +------------------------+ +---------------------+ > > > We are trying to run test program `test_pps_input` in order to see if PPS > is working as expected. > When running without any argument, the PPS is correctly detected, I > suppose it is because it uses as time source `internal`. > Then when I try to use `sfp0` as a time source, I observed 2 different > behaviors: > > Command run: ./test_pps_input > --args="clock_source=internal,time_source=sfp0" --source=sfp0 > > 1. I get the following message: > > [ERROR] [RPC] TDC Failed to reset. > [INFO] [MPM.Rhodium-0.init.LMK04828] LMK initialized and locked! > [ERROR] [MPM.Sync-0] TDC Failed to Reset! Check your clocks! Status: 0x0 > [ERROR] [MPM.RPCServer] init() failed with error: TDC Failed to reset. > Error: RuntimeError: Error during RPC call to `init'. Error message: TDC > Failed to reset. > > And after this message, the PPS led does not blink anymore. > > 2. > If I then run again the test after failing previously, this time I don't > get any error message but a exception is thrown because no PPS was detected. > > We know that the OPNT Timing switch works when used with a OPNT node, > where we get PPS and 10MHz signals. > > Do you think that there could be an issue when N320 and OPNT Switch try to > sync together, or do you have any idea of what I could explore ? > > Thank you in advance for any help you can provide me with. > > Best, > Julián > _______________________________________________ > USRP-users mailing list -- usrp-users@lists.ettus.com<mailto: > usrp-users@lists.ettus.com> > To unsubscribe send an email to usrp-users-le...@lists.ettus.com<mailto: > usrp-users-le...@lists.ettus.com> > _______________________________________________ > USRP-users mailing list -- usrp-users@lists.ettus.com > To unsubscribe send an email to usrp-users-le...@lists.ettus.com >
_______________________________________________ USRP-users mailing list -- usrp-users@lists.ettus.com To unsubscribe send an email to usrp-users-le...@lists.ettus.com
