Works beautifully. Thanks, Sam. Akın
9 Oca 2020 Per 21:54 tarihinde Sam Reiter <sam.rei...@ettus.com> şunu yazdı: > Akin, > > I'd recommend you check out our DPDK setup guide - hot off the presses: > > https://kb.ettus.com/Getting_Started_with_DPDK_and_UHD > > Sam Reiter > Ettus Research > > > On Wed, Jan 8, 2020 at 10:52 PM akin soysal via USRP-users < > usrp-users@lists.ettus.com> wrote: > >> >> >> ---------- Forwarded message --------- >> Gönderen: akin soysal <akinsoy...@gmail.com> >> Date: 8 Oca 2020 Çar 15:22 >> Subject: dpdk-test does not work >> To: USRP-users@lists.ettus.com <usrp-users@lists.ettus.com> >> >> >> Dear all, >> >> We have a USRP X310 setup and we are trying to make the >> UHD_3.15.0.0-0-g4e06022c driver work. I have added a file under >> /etc/uhd/uhd.conf and it is attached to this email. >> >> I am not sure about the dpdk-mac and dpdk-ipv4 addresses, what are they >> used for? >> >> I am trying to make the dpdk-test work but I am experiencing problems >> with setting of ipv4. >> >> ----- >> sudo ./dpdk_test >> EAL: Detected 18 lcore(s) >> EAL: No free hugepages reported in hugepages-1048576kB >> EAL: Probing VFIO support... >> EAL: VFIO support initialized >> EAL: PCI device 0000:05:00.0 on NUMA socket 0 >> EAL: probe driver: 8086:1533 net_e1000_igb >> EAL: PCI device 0000:65:00.0 on NUMA socket 0 >> EAL: probe driver: 8086:1557 net_ixgbe >> EAL: using IOMMU type 1 (Type 1) >> EAL: Ignore mapping IO port bar(2) >> EAL: Waiting for links to come up... >> [INFO] [UHD] linux; GNU C++ version 4.8.5 20150623 (Red Hat 4.8.5-39); >> Boost_105800; UHD_3.15.0.0-0-g4e06022c >> EAL: Init DONE! >> EAL: Starting I/O threads! >> terminate called after throwing an instance of 'uhd::assertion_error' >> what(): AssertionError: status == 0 >> in std::string get_ipv4_addr(unsigned int) >> at /home/ulak-gnb/workarea-uhd/uhd/host/tests/dpdk_test.cpp:229 >> >> Aborted >> ----- >> >> What should be the uhd-dpdk arguments for this to run? It seems like it >> does not even read the uhd.conf file. >> >> I am using DPDK dpdk-stable-17.11.9. I have also programmed my SFP+ >> interface via dpdk-devbind.py as shown below. >> >> ---------- >> sudo ./dpdk-devbind.py -s >> >> Network devices using DPDK-compatible driver >> ============================================ >> 0000:65:00.0 '82599 10 Gigabit Network Connection 1557' drv=vfio-pci >> unused=ixgbe >> >> Network devices using kernel driver >> =================================== >> 0000:04:00.0 'AQC108 NBase-T/IEEE 802.3bz Ethernet Controller [AQtion] >> d108' if=eth1 drv=atlantic unused=vfio-pci >> 0000:05:00.0 'I210 Gigabit Network Connection 1533' if=eno1 drv=igb >> unused=vfio-pci *Active* >> >> Other Network devices >> ===================== >> <none> >> >> Crypto devices using DPDK-compatible driver >> =========================================== >> <none> >> >> Crypto devices using kernel driver >> ================================== >> <none> >> >> Other Crypto devices >> ==================== >> <none> >> >> Eventdev devices using DPDK-compatible driver >> ============================================= >> <none> >> >> Eventdev devices using kernel driver >> ==================================== >> <none> >> >> Other Eventdev devices >> ====================== >> <none> >> >> Mempool devices using DPDK-compatible driver >> ============================================ >> <none> >> >> Mempool devices using kernel driver >> =================================== >> <none> >> >> Other Mempool devices >> ===================== >> <none> >> ---------- >> >> Thanks and regards, >> Akın >> _______________________________________________ >> USRP-users mailing list >> USRP-users@lists.ettus.com >> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com >> >
_______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
