Hi all,
I'm having trouble running osmotrx with an Ettus B210. I'm not sure where
the issue is so figured I would ask here.
Running the binary for osmo-trx on Ubuntu 18.04, I see:
:~$ sudo osmo-trx
linux; GNU C++ version 7.3.0; Boost_106501; UHD_003.010.003.000-0-unknown
opening configuration table from path :memory:
Config Settings
Log Level............... NOTICE
Device args.............
TRX Base Port........... 5700
TRX Address............. 127.0.0.1
Channels................ 1
Tx Samples-per-Symbol... 4
Rx Samples-per-Symbol... 1
EDGE support............ Disabled
Reference............... Internal
C0 Filler Table......... Disabled
Multi-Carrier........... Disabled
Diversity............... Disabled
Tuning offset........... 0
RSSI to dBm offset...... 0
Swap channels........... 0
-- Detected Device: B210
-- Operating over USB 3.
ALERT 140391490980800 13:45:44.2 UHDDevice.cpp:799:open: UHD make failed,
device
ALERT 140391490980800 13:45:44.2 UHDDevice.cpp:799:open: UHD make failed,
device
ALERT 140391490980800 13:45:44.2 osmo-trx.cpp:530:main: Failed to create
radio device
ALERT 140391490980800 13:45:44.2 osmo-trx.cpp:530:main: Failed to create
radio device
Shutting down transceiver...
The output is similar with `sudo osmo-trx -a serial=31502DD`, and the
output of uhd_find_devices looks normal to me:
:~$ uhd_find_devices
[INFO] [UHD] linux; GNU C++ version 7.3.0; Boost_106501;
UHD_3.13.0.1-release
--------------------------------------------------
-- UHD Device 0
--------------------------------------------------
Device Address:
serial: 31502DD
name: MyB210
product: B210
type: b200
I get similar results with or without the suggested udev rules[1].
Looking at the osmo-trx source[2] I am confused why it would identify the
device and then fail the UHD make step. It seems like
`uhd::usrp::multi_usrp::make`
throws exceptions if the device is not found.
I've been stuck on this for a while and would appreciate any pointers or
ideas of what else to try. In case it helps I'll include the output of
uhd_usrp_probe.
Thanks,
--Michael
[1] https://files.ettus.com/manual/page_transport.html
[2]
https://github.com/osmocom/osmo-trx/blob/74bcc562a9403e224c40a9db77753b81cd412a70/Transceiver52M/device/uhd/UHDDevice.cpp#L632
-----
:~$ sudo uhd_usrp_probe
[INFO] [UHD] linux; GNU C++ version 7.3.0; Boost_106501;
UHD_3.13.0.1-release
[INFO] [B200] Detected Device: B210
[INFO] [B200] Operating over USB 3.
[INFO] [B200] Detecting internal GPSDO....
[INFO] [GPS] No GPSDO found
[INFO] [B200] Initialize CODEC control...
[INFO] [B200] Initialize Radio control...
[INFO] [B200] Performing register loopback test...
[INFO] [B200] Register loopback test passed
[INFO] [B200] Performing register loopback test...
[INFO] [B200] Register loopback test passed
[INFO] [B200] Setting master clock rate selection to 'automatic'.
[INFO] [B200] Asking for clock rate 16.000000 MHz...
[INFO] [B200] Actually got clock rate 16.000000 MHz.
_____________________________________________________
/
| Device: B-Series Device
| _____________________________________________________
| /
| | Mboard: B210
| | revision: 4
| | product: 2
| | serial: 31502DD
| | name: MyB210
| | FW Version: 8.0
| | FPGA Version: 15.0
| |
| | Time sources: none, internal, external, gpsdo
| | Clock sources: internal, external, gpsdo
| | Sensors: ref_locked
| | _____________________________________________________
| | /
| | | RX DSP: 0
| | |
| | | Freq range: -8.000 to 8.000 MHz
| | _____________________________________________________
| | /
| | | RX DSP: 1
| | |
| | | Freq range: -8.000 to 8.000 MHz
| | _____________________________________________________
| | /
| | | RX Dboard: A
| | | _____________________________________________________
| | | /
| | | | RX Frontend: A
| | | | Name: FE-RX2
| | | | Antennas: TX/RX, RX2
| | | | Sensors: temp, rssi, lo_locked
| | | | Freq range: 50.000 to 6000.000 MHz
| | | | Gain range PGA: 0.0 to 76.0 step 1.0 dB
| | | | Bandwidth range: 200000.0 to 56000000.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | RX Frontend: B
| | | | Name: FE-RX1
| | | | Antennas: TX/RX, RX2
| | | | Sensors: temp, rssi, lo_locked
| | | | Freq range: 50.000 to 6000.000 MHz
| | | | Gain range PGA: 0.0 to 76.0 step 1.0 dB
| | | | Bandwidth range: 200000.0 to 56000000.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | RX Codec: A
| | | | Name: B210 RX dual ADC
| | | | Gain Elements: None
| | _____________________________________________________
| | /
| | | TX DSP: 0
| | |
| | | Freq range: -8.000 to 8.000 MHz
| | _____________________________________________________
| | /
| | | TX DSP: 1
| | |
| | | Freq range: -8.000 to 8.000 MHz
| | _____________________________________________________
| | /
| | | TX Dboard: A
| | | _____________________________________________________
| | | /
| | | | TX Frontend: A
| | | | Name: FE-TX2
| | | | Antennas: TX/RX
| | | | Sensors: temp, lo_locked
| | | | Freq range: 50.000 to 6000.000 MHz
| | | | Gain range PGA: 0.0 to 89.8 step 0.2 dB
| | | | Bandwidth range: 200000.0 to 56000000.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | TX Frontend: B
| | | | Name: FE-TX1
| | | | Antennas: TX/RX
| | | | Sensors: temp, lo_locked
| | | | Freq range: 50.000 to 6000.000 MHz
| | | | Gain range PGA: 0.0 to 89.8 step 0.2 dB
| | | | Bandwidth range: 200000.0 to 56000000.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | TX Codec: A
| | | | Name: B210 TX dual DAC
| | | | Gain Elements: None
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
