Michael,
I got a chance to test the latest 3.13 changes with regard to the Rx
timeouts discussed in this thread.  On my N310, the timeouts seem to be
fixed - I did not experience any in my testing.  However, on the X310, I
still occasionally get a timeout using the same
"txrx_loopback_to_file_repeat" program I attached earlier in this thread.

Rob

A few remarks

   - Below you will find the console output for
   txrx_loopback_to_file_repeat followed by the output for uhd_usrp_probe
   - Note below the error (timeout) on iterations 8 and 14
   - Previously, after an error occurred, all subsequent iterations would
   fail, but this is not the case anymore.  In fact, for all iterations, the
   desired data capture completed successfully - the timeout happened during
   the "flush" operation.
   - The error does not always occur in this program which is hardcoded for
   50 iterations.  So, if no error occurs, simply run again and likely there
   will be at least one error.
   - Note that I changed some of the command line parameters (such as
   tx-rate and rx-rate) in an attempt to make the error occur more often, but
   I really don't know if it matters


$ txrx_loopback_to_file_repeat --tx-args="addr=192.168.46.2"
--rx-args="addr=192.168.46.2" --nsamps=1000000 --tx-rate=50e6
--rx-rate=100e6 --tx-channels=0,1 --rx-channels=0,1 --tx-freq=2500e6
--rx-freq=2500e6 --file=/media/ramfolder/usrp_samples

Creating the transmit usrp device with: addr=192.168.46.2...
[INFO] [UHD] linux; GNU C++ version 5.4.0 20160609; Boost_105800;
UHD_3.13.0.3-0-g85347b89
[INFO] [X300] X300 initialization sequence...
[INFO] [X300] Maximum frame size: 8000 bytes.
[INFO] [X300] Radio 1x clock: 200 MHz
[INFO] [0/DmaFIFO_0] Initializing block control (NOC ID: 0xF1F0D00000000000)
[INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1296 MB/s)
[INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1306 MB/s)
[INFO] [0/Radio_0] Initializing block control (NOC ID: 0x12AD100000000001)
[INFO] [0/Radio_1] Initializing block control (NOC ID: 0x12AD100000000001)
[INFO] [0/DDC_0] Initializing block control (NOC ID: 0xDDC0000000000000)
[INFO] [0/DDC_1] Initializing block control (NOC ID: 0xDDC0000000000000)
[INFO] [0/DUC_0] Initializing block control (NOC ID: 0xD0C0000000000000)
[INFO] [0/DUC_1] Initializing block control (NOC ID: 0xD0C0000000000000)

Creating the receive usrp device with: addr=192.168.46.2...
Using TX Device: Single USRP:
  Device: X-Series Device
  Mboard 0: X310
  RX Channel: 0
    RX DSP: 0
    RX Dboard: A
    RX Subdev: UBX RX
  RX Channel: 1
    RX DSP: 0
    RX Dboard: B
    RX Subdev: UBX RX
  TX Channel: 0
    TX DSP: 0
    TX Dboard: A
    TX Subdev: UBX TX
  TX Channel: 1
    TX DSP: 0
    TX Dboard: B
    TX Subdev: UBX TX

Using RX Device: Single USRP:
  Device: X-Series Device
  Mboard 0: X310
  RX Channel: 0
    RX DSP: 0
    RX Dboard: A
    RX Subdev: UBX RX
  RX Channel: 1
    RX DSP: 0
    RX Dboard: B
    RX Subdev: UBX RX
  TX Channel: 0
    TX DSP: 0
    TX Dboard: A
    TX Subdev: UBX TX
  TX Channel: 1
    TX DSP: 0
    TX Dboard: B
    TX Subdev: UBX TX

Setting TX Rate: 50.000000 Msps...
Actual TX Rate: 50.000000 Msps...

Setting RX Rate: 100.000000 Msps...
Actual RX Rate: 100.000000 Msps...

Configuring TX Channel 0
Setting TX Freq: 2500.000000 MHz...
Actual TX Freq: 2500.000000 MHz...

Configuring TX Channel 1
Setting TX Freq: 2500.000000 MHz...
Actual TX Freq: 2500.000000 MHz...

Configuring RX Channel 0
Setting RX Freq: 2500.000000 MHz...
Actual RX Freq: 2500.000000 MHz...

Configuring RX Channel 1
Setting RX Freq: 2500.000000 MHz...
Actual RX Freq: 2500.000000 MHz...

Checking TX: TXLO: locked ...
Checking RX: RXLO: locked ...
Setting device timestamp to 0...
Iteration 0 at time 0.212949
  Num samples received: 1017960
  Flush samps received: 19393; EOB: 1; ERR: 0
Iteration 1 at time 0.434254
  Num samples received: 1017960
  Flush samps received: 11682; EOB: 1; ERR: 0
Iteration 2 at time 0.655387
  Num samples received: 1017960
  Flush samps received: 15294; EOB: 1; ERR: 0
Iteration 3 at time 0.87674
  Num samples received: 1017960
  Flush samps received: 12270; EOB: 1; ERR: 0
Iteration 4 at time 1.09799
  Num samples received: 1017960
  Flush samps received: 15745; EOB: 1; ERR: 0
Iteration 5 at time 1.31925
  Num samples received: 1017960
  Flush samps received: 19960; EOB: 0; ERR: 0
  Flush samps received: 3214; EOB: 1; ERR: 0
Iteration 6 at time 1.54068
  Num samples received: 1017960
  Flush samps received: 16435; EOB: 1; ERR: 0
Iteration 7 at time 1.7619
  Num samples received: 1017960
  Flush samps received: 19339; EOB: 1; ERR: 0
Iteration 8 at time 1.98327
  Num samples received: 1017960
  Flush samps received: 19960; EOB: 0; ERR: 0
  Flush samps received: 1996; EOB: 0; ERR: 0
  Flush samps received: 0; EOB: 0; ERR: 1
Iteration 9 at time 2.40473
  Num samples received: 1017960
  Flush samps received: 19960; EOB: 0; ERR: 0
  Flush samps received: 1870; EOB: 1; ERR: 0
Iteration 10 at time 2.62615
  Num samples received: 1017960
  Flush samps received: 19960; EOB: 0; ERR: 0
  Flush samps received: 3659; EOB: 1; ERR: 0
Iteration 11 at time 2.84743
  Num samples received: 1017960
  Flush samps received: 19019; EOB: 1; ERR: 0
Iteration 12 at time 3.06864
  Num samples received: 1017960
  Flush samps received: 16446; EOB: 1; ERR: 0
Iteration 13 at time 3.28997
  Num samples received: 1017960
  Flush samps received: 11355; EOB: 1; ERR: 0
Iteration 14 at time 3.51127
  Num samples received: 1017960
  Flush samps received: 17964; EOB: 0; ERR: 0
  Flush samps received: 0; EOB: 0; ERR: 1
Iteration 15 at time 3.93273
  Num samples received: 1017960
  Flush samps received: 19960; EOB: 0; ERR: 0
  Flush samps received: 1100; EOB: 1; ERR: 0
Iteration 16 at time 4.15405
  Num samples received: 1017960
  Flush samps received: 19630; EOB: 1; ERR: 0
Iteration 17 at time 4.37537
  Num samples received: 1017960
  Flush samps received: 19960; EOB: 0; ERR: 0
  Flush samps received: 555; EOB: 1; ERR: 0
Iteration 18 at time 4.59675
  Num samples received: 1017960
  Flush samps received: 11456; EOB: 1; ERR: 0
Iteration 19 at time 4.81791
  Num samples received: 1017960
  Flush samps received: 12014; EOB: 1; ERR: 0
Iteration 20 at time 5.0393
  Num samples received: 1017960
  Flush samps received: 17758; EOB: 1; ERR: 0
Iteration 21 at time 5.26061
  Num samples received: 1017960
  Flush samps received: 11894; EOB: 1; ERR: 0
Iteration 22 at time 5.48183
  Num samples received: 1017960
  Flush samps received: 17742; EOB: 1; ERR: 0
Iteration 23 at time 5.70304
  Num samples received: 1017960
  Flush samps received: 13635; EOB: 1; ERR: 0
Iteration 24 at time 5.92424
  Num samples received: 1017960
  Flush samps received: 13918; EOB: 1; ERR: 0
Iteration 25 at time 6.14547
  Num samples received: 1017960
  Flush samps received: 13891; EOB: 1; ERR: 0
Iteration 26 at time 6.36667
  Num samples received: 1017960
  Flush samps received: 16441; EOB: 1; ERR: 0
Iteration 27 at time 6.58795
  Num samples received: 1017960
  Flush samps received: 12009; EOB: 1; ERR: 0
Iteration 28 at time 6.80918
  Num samples received: 1017960
  Flush samps received: 19960; EOB: 0; ERR: 0
  Flush samps received: 4065; EOB: 1; ERR: 0
Iteration 29 at time 7.03052
  Num samples received: 1017960
  Flush samps received: 18035; EOB: 1; ERR: 0
Iteration 30 at time 7.25181
  Num samples received: 1017960
  Flush samps received: 18619; EOB: 1; ERR: 0
Iteration 31 at time 7.47297
  Num samples received: 1017960
  Flush samps received: 15896; EOB: 1; ERR: 0
Iteration 32 at time 7.69416
  Num samples received: 1017960
  Flush samps received: 19854; EOB: 1; ERR: 0
Iteration 33 at time 7.91547
  Num samples received: 1017960
  Flush samps received: 18318; EOB: 1; ERR: 0
Iteration 34 at time 8.13672
  Num samples received: 1017960
  Flush samps received: 16676; EOB: 1; ERR: 0
Iteration 35 at time 8.35796
  Num samples received: 1017960
  Flush samps received: 16083; EOB: 1; ERR: 0
Iteration 36 at time 8.57916
  Num samples received: 1017960
  Flush samps received: 15737; EOB: 1; ERR: 0
Iteration 37 at time 8.80039
  Num samples received: 1017960
  Flush samps received: 17694; EOB: 1; ERR: 0
Iteration 38 at time 9.02171
  Num samples received: 1017960
  Flush samps received: 12233; EOB: 1; ERR: 0
Iteration 39 at time 9.24293
  Num samples received: 1017960
  Flush samps received: 13635; EOB: 1; ERR: 0
Iteration 40 at time 9.46412
  Num samples received: 1017960
  Flush samps received: 14291; EOB: 1; ERR: 0
Iteration 41 at time 9.68535
  Num samples received: 1017960
  Flush samps received: 19960; EOB: 0; ERR: 0
  Flush samps received: 161; EOB: 1; ERR: 0
Iteration 42 at time 9.90668
  Num samples received: 1017960
  Flush samps received: 15625; EOB: 1; ERR: 0
Iteration 43 at time 10.1279
  Num samples received: 1017960
  Flush samps received: 17891; EOB: 1; ERR: 0
Iteration 44 at time 10.3491
  Num samples received: 1017960
  Flush samps received: 19960; EOB: 0; ERR: 0
  Flush samps received: 5097; EOB: 1; ERR: 0
Iteration 45 at time 10.5706
  Num samples received: 1017960
  Flush samps received: 11640; EOB: 1; ERR: 0
Iteration 46 at time 10.7917
  Num samples received: 1017960
  Flush samps received: 13350; EOB: 1; ERR: 0
Iteration 47 at time 11.013
  Num samples received: 1017960
  Flush samps received: 18625; EOB: 1; ERR: 0
Iteration 48 at time 11.2342
  Num samples received: 1017960
  Flush samps received: 13630; EOB: 1; ERR: 0
Iteration 49 at time 11.4554
  Num samples received: 1017960
  Flush samps received: 15897; EOB: 1; ERR: 0

Done!

$ uhd_usrp_probe
[INFO] [UHD] linux; GNU C++ version 5.4.0 20160609; Boost_105800;
UHD_3.13.0.3-0-g85347b89
[INFO] [X300] X300 initialization sequence...
[INFO] [X300] Maximum frame size: 8000 bytes.
[INFO] [X300] Radio 1x clock: 200 MHz
[INFO] [0/DmaFIFO_0] Initializing block control (NOC ID: 0xF1F0D00000000000)
[INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1317 MB/s)
[INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1317 MB/s)
[INFO] [0/Radio_0] Initializing block control (NOC ID: 0x12AD100000000001)
[INFO] [0/Radio_1] Initializing block control (NOC ID: 0x12AD100000000001)
[INFO] [0/DDC_0] Initializing block control (NOC ID: 0xDDC0000000000000)
[INFO] [0/DDC_1] Initializing block control (NOC ID: 0xDDC0000000000000)
[INFO] [0/DUC_0] Initializing block control (NOC ID: 0xD0C0000000000000)
[INFO] [0/DUC_1] Initializing block control (NOC ID: 0xD0C0000000000000)
  _____________________________________________________
 /
|       Device: X-Series Device
|     _____________________________________________________
|    /
|   |       Mboard: X310
|   |   revision: 8
|   |   revision_compat: 7
|   |   product: 30818
|   |   mac-addr0: 00:80:2f:25:85:bf
|   |   mac-addr1: 00:80:2f:25:85:c0
|   |   gateway: 192.168.10.1
|   |   ip-addr0: 192.168.10.2
|   |   subnet0: 255.255.255.0
|   |   ip-addr1: 192.168.20.2
|   |   subnet1: 255.255.255.0
|   |   ip-addr2: 192.168.146.2
|   |   subnet2: 255.255.255.0
|   |   ip-addr3: 192.168.46.2
|   |   subnet3: 255.255.255.0
|   |   serial: 30DF0D1
|   |   FW Version: 6.0
|   |   FPGA Version: 35.1
|   |   FPGA git hash: c429b31
|   |   RFNoC capable: Yes
|   |
|   |   Time sources:  internal, external, gpsdo
|   |   Clock sources: internal, external, gpsdo
|   |   Sensors: ref_locked
|   |     _____________________________________________________
|   |    /
|   |   |       RX Dboard: A
|   |   |   ID: UBX-160 v1 (0x007a)
|   |   |   Serial: 30B6D2A
|   |   |     _____________________________________________________
|   |   |    /
|   |   |   |       RX Frontend: 0
|   |   |   |   Name: UBX RX
|   |   |   |   Antennas: TX/RX, RX2, CAL
|   |   |   |   Sensors: lo_locked
|   |   |   |   Freq range: 10.000 to 6000.000 MHz
|   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
|   |   |   |   Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz
|   |   |   |   Connection Type: IQ
|   |   |   |   Uses LO offset: No
|   |   |     _____________________________________________________
|   |   |    /
|   |   |   |       RX Codec: A
|   |   |   |   Name: ads62p48
|   |   |   |   Gain range digital: 0.0 to 6.0 step 0.5 dB
|   |     _____________________________________________________
|   |    /
|   |   |       RX Dboard: B
|   |   |   ID: UBX-160 v1 (0x007a)
|   |   |   Serial: 30B6D1D
|   |   |     _____________________________________________________
|   |   |    /
|   |   |   |       RX Frontend: 0
|   |   |   |   Name: UBX RX
|   |   |   |   Antennas: TX/RX, RX2, CAL
|   |   |   |   Sensors: lo_locked
|   |   |   |   Freq range: 10.000 to 6000.000 MHz
|   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
|   |   |   |   Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz
|   |   |   |   Connection Type: IQ
|   |   |   |   Uses LO offset: No
|   |   |     _____________________________________________________
|   |   |    /
|   |   |   |       RX Codec: B
|   |   |   |   Name: ads62p48
|   |   |   |   Gain range digital: 0.0 to 6.0 step 0.5 dB
|   |     _____________________________________________________
|   |    /
|   |   |       TX Dboard: A
|   |   |   ID: UBX-160 v1 (0x0079)
|   |   |   Serial: 30B6D2A
|   |   |     _____________________________________________________
|   |   |    /
|   |   |   |       TX Frontend: 0
|   |   |   |   Name: UBX TX
|   |   |   |   Antennas: TX/RX, CAL
|   |   |   |   Sensors: lo_locked
|   |   |   |   Freq range: 10.000 to 6000.000 MHz
|   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
|   |   |   |   Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz
|   |   |   |   Connection Type: QI
|   |   |   |   Uses LO offset: No
|   |   |     _____________________________________________________
|   |   |    /
|   |   |   |       TX Codec: A
|   |   |   |   Name: ad9146
|   |   |   |   Gain Elements: None
|   |     _____________________________________________________
|   |    /
|   |   |       TX Dboard: B
|   |   |   ID: UBX-160 v1 (0x0079)
|   |   |   Serial: 30B6D1D
|   |   |     _____________________________________________________
|   |   |    /
|   |   |   |       TX Frontend: 0
|   |   |   |   Name: UBX TX
|   |   |   |   Antennas: TX/RX, CAL
|   |   |   |   Sensors: lo_locked
|   |   |   |   Freq range: 10.000 to 6000.000 MHz
|   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
|   |   |   |   Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz
|   |   |   |   Connection Type: QI
|   |   |   |   Uses LO offset: No
|   |   |     _____________________________________________________
|   |   |    /
|   |   |   |       TX Codec: B
|   |   |   |   Name: ad9146
|   |   |   |   Gain Elements: None
|   |     _____________________________________________________
|   |    /
|   |   |       RFNoC blocks on this device:
|   |   |
|   |   |   * DmaFIFO_0
|   |   |   * Radio_0
|   |   |   * Radio_1
|   |   |   * DDC_0
|   |   |   * DDC_1
|   |   |   * DUC_0
|   |   |   * DUC_1




On Mon, Sep 17, 2018 at 11:12 AM Rob Kossler <rkoss...@nd.edu> wrote:

> Hi Michael,
> Were these issues resolved in a recent commit (included in 3.13.0.3 RC)?
> Rob
>
> On Thu, Sep 6, 2018 at 2:12 PM Michael West <michael.w...@ettus.com>
> wrote:
>
>> Update:  The issue is included on the head of the UHD-3.12 branch, but is
>> not included in the v3.12.0.0 release.  So, be sure to checkout the
>> v3.12.0.0 tag.
>>
>> The issue we replicated is the STREAM_CMD_NUM_SAMPS_AND_DONE.  The
>> continuous streaming issue is still outstanding, but may be related.
>>
>> Regards,
>> Michael
>>
>> On Thu, Sep 6, 2018 at 10:57 AM, Rob Kossler <rkoss...@nd.edu> wrote:
>>
>>> OK. I will give it a shot.  Which issue did you duplicate (the confusion
>>> is my fault for discussing two different issues in the same thread): Issue
>>> #1 (NUM_SAMPS_AND_DONE) or Issue #2 (CONTINUOUS)?
>>>
>>> Rob
>>>
>>> On Thu, Sep 6, 2018 at 1:52 PM Michael West <michael.w...@ettus.com>
>>> wrote:
>>>
>>>> Hi Rob,
>>>>
>>>> Thank you once again.  We have reproduced the issue and are working on
>>>> tracing down the root cause and fixing the issue.  We have confirmed that
>>>> the issue exists on 3.13, but we have also confirmed it does not exist on
>>>> 3.12.0.0.  So, you can use v3.12.0.0 in the meantime.  To be sure you are
>>>> using the correct FPGA image for v3.12.0.0, be sure to run
>>>> 'uhd_images_downloader --refetch'.
>>>>
>>>> Regards,
>>>> Michael
>>>>
>>>> On Tue, Sep 4, 2018 at 3:21 PM, Rob Kossler via USRP-users <
>>>> usrp-users@lists.ettus.com> wrote:
>>>>
>>>>> Today, I confirmed that this issue exists on the head of 3.13 and
>>>>> 3.12, but not 3.11.  The example program provided with my previous post 
>>>>> can
>>>>> be compiled with any of these versions.
>>>>>
>>>>> Rob
>>>>>
>>>>> On Fri, Aug 31, 2018 at 12:33 PM Rob Kossler <rkoss...@nd.edu> wrote:
>>>>>
>>>>>> In this post and one other post, I mentioned two issues I am having
>>>>>> related to N310 streaming:
>>>>>>
>>>>>>    1. With STREAM_MODE_NUM_SAMPS_AND_DONE, sometimes I get a timeout
>>>>>>    prior to receiving the requested number of samples (this is the issue
>>>>>>    identified in this post). This may be simply dependent upon the 
>>>>>> number of
>>>>>>    samples requested.
>>>>>>    2. With STREAM_MODE_START_CONTINUOUS, I get errors with repeated
>>>>>>    captures such that after several successful captures, I eventually 
>>>>>> get a
>>>>>>    streaming timeout and all subsequent captures fail.
>>>>>>
>>>>>> So, turns out that this issue is bigger for me than I realized.  I
>>>>>> had a bunch of trouble yesterday while doing some research 
>>>>>> experimentation.
>>>>>> I had selected to go with X310 devices rather than N310 devices because 
>>>>>> of
>>>>>> their relative maturity.  Today, I confirmed that my issues yesterday 
>>>>>> with
>>>>>> the X310 are the same as I previously mentioned for the N310 (#2 above).
>>>>>> So, perhaps it is an issue with UHD-3.13 (I did not check any other 
>>>>>> branch).
>>>>>>
>>>>>> I modified the Ettus "txrx_loopback_to_file.cpp" code to include a
>>>>>> "for loop of 50 iterations" and changed the streaming mode to be
>>>>>> continuous.  The modified source is included as an attachment (a 'diff' 
>>>>>> of
>>>>>> my code to the original with show the minor changes I made).  I attached 
>>>>>> a
>>>>>> console log of the output messages when run with my X310 which shows both
>>>>>> the command line parameters I used as well as the resulting errors.  Note
>>>>>> that everything is going as expected through Iteration 5, but starting at
>>>>>> Iteration 6, there is no end-of-burst (EOB) and starting at Iteration 8, 
>>>>>> a
>>>>>> timeout occurs prior to receiving any samples.
>>>>>>
>>>>>> Please let me know if you have any questions.  This is a pretty big
>>>>>> issue for me and will prevent me from using 3.13 until addressed.
>>>>>>
>>>>>> Rob
>>>>>>
>>>>>>
>>>>>> On Fri, Aug 24, 2018 at 2:46 PM Rob Kossler <rkoss...@nd.edu> wrote:
>>>>>>
>>>>>>> Hi,
>>>>>>> This post is perhaps a continuation of a previous post "Problems
>>>>>>> with MPM 3.13 on N310", but I wanted to change the subject to reflect 
>>>>>>> this
>>>>>>> current issue.
>>>>>>>
>>>>>>> The issue is an Rx streaming timeout.  It can be easily duplicated
>>>>>>> with a stock Ettus example.  Below you will find the console log which
>>>>>>> includes the command line parameters.  Note the following:
>>>>>>>
>>>>>>>    - I requested 31250 samples
>>>>>>>    - There is a error "Timeout while streaming" indicated at the end
>>>>>>>    - The final file size of 119340 indicates that 29835 samples
>>>>>>>    were received
>>>>>>>    - I do not have any reason to believe that the specific command
>>>>>>>    line arguments below are needed to duplicate the issue.  I just 
>>>>>>> didn't
>>>>>>>    bother to try other ones.
>>>>>>>
>>>>>>> In the other thread, I mentioned that my Rx timeout issue had gone
>>>>>>> away after switching to streaming mode STREAM_MODE_NUM_SAMPS_AND_DONE.
>>>>>>> However, the issue below occurs when using that mode so it will be a
>>>>>>> problem for me.
>>>>>>>
>>>>>>> Let me know if you have any questions.
>>>>>>>
>>>>>>> Rob
>>>>>>>
>>>>>>>
>>>>>>> irisheyes9@irisheyes9-Z240-SFF:/media/SSD_RAID/multi_pol$
>>>>>>> txrx_loopback_to_file --tx-args="addr=192.168.61.2"
>>>>>>> --rx-args="addr=192.168.61.2" --nsamps=31250 --tx-rate=31.25e6
>>>>>>> --rx-rate=31.25e6 --tx-channels=0,1 --rx-channels=2,3 --tx-freq=2500e6
>>>>>>> --rx-freq=2500e6
>>>>>>>
>>>>>>> Creating the transmit usrp device with: addr=192.168.61.2...
>>>>>>> [INFO] [UHD] linux; GNU C++ version 5.4.0 20160609; Boost_105800;
>>>>>>> UHD_3.13.0.2-0-g0ddc19e5
>>>>>>> [INFO] [MPMD] Initializing 1 device(s) in parallel with args:
>>>>>>> mgmt_addr=192.168.61.2,type=n3xx,product=n310,serial=315A34B,claimed=False,addr=192.168.61.2
>>>>>>> [INFO] [MPM.PeriphManager] init() called with device args
>>>>>>> `mgmt_addr=192.168.61.2,product=n310'.
>>>>>>> [INFO] [0/DmaFIFO_0] Initializing block control (NOC ID:
>>>>>>> 0xF1F0D00000000004)
>>>>>>> [INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1320 MB/s)
>>>>>>> [INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1336 MB/s)
>>>>>>> [INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1331 MB/s)
>>>>>>> [INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1349 MB/s)
>>>>>>> [INFO] [0/Radio_0] Initializing block control (NOC ID:
>>>>>>> 0x12AD100000011312)
>>>>>>> [INFO] [0/Radio_1] Initializing block control (NOC ID:
>>>>>>> 0x12AD100000011312)
>>>>>>> [INFO] [0/DDC_0] Initializing block control (NOC ID:
>>>>>>> 0xDDC0000000000000)
>>>>>>> [INFO] [0/DDC_1] Initializing block control (NOC ID:
>>>>>>> 0xDDC0000000000000)
>>>>>>> [INFO] [0/DUC_0] Initializing block control (NOC ID:
>>>>>>> 0xD0C0000000000002)
>>>>>>> [INFO] [0/DUC_1] Initializing block control (NOC ID:
>>>>>>> 0xD0C0000000000002)
>>>>>>>
>>>>>>> Creating the receive usrp device with: addr=192.168.61.2...
>>>>>>> Using TX Device: Single USRP:
>>>>>>>   Device: N300-Series Device
>>>>>>>   Mboard 0: ni-n3xx-315A34B
>>>>>>>   RX Channel: 0
>>>>>>>     RX DSP: 0
>>>>>>>     RX Dboard: A
>>>>>>>     RX Subdev: Magnesium
>>>>>>>   RX Channel: 1
>>>>>>>     RX DSP: 1
>>>>>>>     RX Dboard: A
>>>>>>>     RX Subdev: Magnesium
>>>>>>>   RX Channel: 2
>>>>>>>     RX DSP: 0
>>>>>>>     RX Dboard: B
>>>>>>>     RX Subdev: Magnesium
>>>>>>>   RX Channel: 3
>>>>>>>     RX DSP: 1
>>>>>>>     RX Dboard: B
>>>>>>>     RX Subdev: Magnesium
>>>>>>>   TX Channel: 0
>>>>>>>     TX DSP: 0
>>>>>>>     TX Dboard: A
>>>>>>>     TX Subdev: Magnesium
>>>>>>>   TX Channel: 1
>>>>>>>     TX DSP: 1
>>>>>>>     TX Dboard: A
>>>>>>>     TX Subdev: Magnesium
>>>>>>>   TX Channel: 2
>>>>>>>     TX DSP: 0
>>>>>>>     TX Dboard: B
>>>>>>>     TX Subdev: Magnesium
>>>>>>>   TX Channel: 3
>>>>>>>     TX DSP: 1
>>>>>>>     TX Dboard: B
>>>>>>>     TX Subdev: Magnesium
>>>>>>>
>>>>>>> Using RX Device: Single USRP:
>>>>>>>   Device: N300-Series Device
>>>>>>>   Mboard 0: ni-n3xx-315A34B
>>>>>>>   RX Channel: 0
>>>>>>>     RX DSP: 0
>>>>>>>     RX Dboard: A
>>>>>>>     RX Subdev: Magnesium
>>>>>>>   RX Channel: 1
>>>>>>>     RX DSP: 1
>>>>>>>     RX Dboard: A
>>>>>>>     RX Subdev: Magnesium
>>>>>>>   RX Channel: 2
>>>>>>>     RX DSP: 0
>>>>>>>     RX Dboard: B
>>>>>>>     RX Subdev: Magnesium
>>>>>>>   RX Channel: 3
>>>>>>>     RX DSP: 1
>>>>>>>     RX Dboard: B
>>>>>>>     RX Subdev: Magnesium
>>>>>>>   TX Channel: 0
>>>>>>>     TX DSP: 0
>>>>>>>     TX Dboard: A
>>>>>>>     TX Subdev: Magnesium
>>>>>>>   TX Channel: 1
>>>>>>>     TX DSP: 1
>>>>>>>     TX Dboard: A
>>>>>>>     TX Subdev: Magnesium
>>>>>>>   TX Channel: 2
>>>>>>>     TX DSP: 0
>>>>>>>     TX Dboard: B
>>>>>>>     TX Subdev: Magnesium
>>>>>>>   TX Channel: 3
>>>>>>>     TX DSP: 1
>>>>>>>     TX Dboard: B
>>>>>>>     TX Subdev: Magnesium
>>>>>>>
>>>>>>> Setting TX Rate: 31.250000 Msps...
>>>>>>> Actual TX Rate: 31.250000 Msps...
>>>>>>>
>>>>>>> Setting RX Rate: 31.250000 Msps...
>>>>>>> Actual RX Rate: 31.250000 Msps...
>>>>>>>
>>>>>>> Configuring TX Channel 0
>>>>>>> Setting TX Freq: 2500.000000 MHz...
>>>>>>> Actual TX Freq: 2500.000000 MHz...
>>>>>>>
>>>>>>> Configuring TX Channel 1
>>>>>>> Setting TX Freq: 2500.000000 MHz...
>>>>>>> Actual TX Freq: 2500.000000 MHz...
>>>>>>>
>>>>>>> Configuring RX Channel 2
>>>>>>> Setting RX Freq: 2500.000000 MHz...
>>>>>>> Actual RX Freq: 2500.000000 MHz...
>>>>>>>
>>>>>>> Configuring RX Channel 3
>>>>>>> Setting RX Freq: 2500.000000 MHz...
>>>>>>> Actual RX Freq: 2500.000000 MHz...
>>>>>>>
>>>>>>> Checking TX: all_los: locked ...
>>>>>>> Checking RX: all_los: locked ...
>>>>>>> Setting device timestamp to 0...
>>>>>>> Timeout while streaming
>>>>>>>
>>>>>>> Done!
>>>>>>>
>>>>>>> irisheyes9@irisheyes9-Z240-SFF:/media/SSD_RAID/multi_pol$ ls -l
>>>>>>> *.dat
>>>>>>> -rw-rw-r-- 1 irisheyes9 irisheyes9 119340 Aug 24 14:33
>>>>>>> usrp_samples.00.dat
>>>>>>> -rw-rw-r-- 1 irisheyes9 irisheyes9 119340 Aug 24 14:33
>>>>>>> usrp_samples.01.dat
>>>>>>> irisheyes9@irisheyes9-Z240-SFF:/media/SSD_RAID/multi_pol$
>>>>>>>
>>>>>>>
>>>>> _______________________________________________
>>>>> USRP-users mailing list
>>>>> USRP-users@lists.ettus.com
>>>>> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
>>>>>
>>>>>
>>>>
>>
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com

Reply via email to