Il 27/05/2014 17:11, heupink ha scritto:
is acting slow, or else?
is there any "benchmark" (ie: timed command) I can issue to test if ldap
Sogo.log tells you for many commands how long they took to complete.
And I don't think a slower ldap would 'slow down' your imap folders.
MJ
Thx all :D
Sogo.log
========
here are last lines whan switching from Inbox to Trash...
192.168.3.22 - - [27/May/2014:17:47:44 GMT] "POST
/SOGo/so/ardito/Mail//0/folderINBOX/uids HTTP/1.1" 200 28/46 2.648 - - 0
192.168.3.22 - - [27/May/2014:17:47:52 GMT] "POST
/SOGo/so/ardito/Mail/0/folderTrash/unseenCount HTTP/1.1" 200 13/0 2.085
- - 0
192.168.3.22 - - [27/May/2014:17:47:52 GMT] "POST
/SOGo/so/ardito/Mail//0/folderTrash/uids HTTP/1.1" 200 386/28 2.127 1124
65% 0
Are those float near the line end, seconds? Because that could likely be
the lag I experiment...2-3 seconds. need more lines?
Then, here some conf files I have atm (keep in mind that is just a test
install, lots of details are just tests. and I disabled any SSL I found,
for now)
/etc/dovecot/local.conf:
====================
disable_plaintext_auth = no
log_path = /var/log/dovecot.message
log_timestamp = "%Y-%m-%d %H:%M:%S "
mail_location = maildir:/var/mail/%u
mail_privileged_group = mail
mail_uid = vmail
mail_gid = vmail
auth_cache_size=5 M
auth_cache_ttl=3600
passdb {
args = /etc/dovecot/dovecot-ldap.conf
driver = ldap
}
passdb {
driver = pam
}
protocols = imap
service auth {
unix_listener auth-master {
group = vmail
mode = 0600
user = vmail
}
unix_listener auth-userdb {
user = vmail
}
user = root
}
userdb {
args = /etc/dovecot/dovecot-ldap.conf
driver = ldap
}
userdb {
driver = passwd
}
protocol lda {
hostname = oc.local
log_path = /var/log/dovecot.message
postmaster_address = [email protected]
}
protocol pop3 {
pop3_uidl_format = %08Xu%08Xv
}
/etc/dovecot/dovecot-ldap.conf (setup "B", eg: local openldap)
===================================================
uris = ldap://localhost:389
dn = cn=admin,dc=oc,dc=local
dnpass = openchange
tls = no
ldap_version = 3
base = dc=oc,dc=local
scope = subtree
user_attrs = homeDirectory=home,uidNumber=uid,gidNumber=gid
user_filter = (uid=%u)
pass_attrs = uid=user,userPassword=password
pass_filter = (uid=%u)
apache (/etc/apache2/conf.d/SOGo.conf)
==================================
Alias /SOGo.woa/WebServerResources/ \
/usr/lib/GNUstep/SOGo/WebServerResources/
Alias /SOGo/WebServerResources/ \
/usr/lib/GNUstep/SOGo/WebServerResources/
<Directory /usr/lib/GNUstep/SOGo/>
AllowOverride None
Order deny,allow
Allow from all
# Explicitly allow caching of static content to avoid browser
specific behavior.
# A resource's URL MUST change in order to have the client load the
new version.
<IfModule expires_module>
ExpiresActive On
ExpiresDefault "access plus 1 year"
</IfModule>
</Directory>
## Uncomment the following to enable proxy-side authentication, you will
then
## need to set the "SOGoTrustProxyAuthentication" SOGo user default to
YES and
## adjust the "x-webobjects-remote-user" proxy header in the "Proxy" section
## below.
#<Location /SOGo>
# AuthType XXX
# Require valid-user
# SetEnv proxy-nokeepalive 1
# Allow from all
#</Location>
ProxyRequests Off
SetEnv proxy-nokeepalive 1
ProxyPreserveHost On
# When using CAS, you should uncomment this and install
cas-proxy-validate.py
# in /usr/lib/cgi-bin to reduce server overloading
#
# ProxyPass /SOGo/casProxy http://localhost/cgi-bin/cas-proxy-validate.py
# <Proxy http://localhost/app/cas-proxy-validate.py>
# Order deny,allow
# Allow from your-cas-host-addr
# </Proxy>
ProxyPass /SOGo http://127.0.0.1:20000/SOGo retry=0
# Enable to use Microsoft ActiveSync support
# Note that you MUST have many sogod workers to use ActiveSync.
# See the SOGo Installation and Configuration guide for more details.
#
#ProxyPass /Microsoft-Server-ActiveSync \
# http://127.0.0.1:20000/SOGo/Microsoft-Server-ActiveSync \
# retry=60 connectiontimeout=5 timeout=360
<Proxy http://127.0.0.1:20000/SOGo>
## adjust the following to your configuration
# RequestHeader set "x-webobjects-server-port" "443"
# RequestHeader set "x-webobjects-server-name" "192.168.3.10"
# RequestHeader set "x-webobjects-server-url" "https://192.168.3.10";
RequestHeader set "x-webobjects-server-port" "80"
RequestHeader set "x-webobjects-server-name" "192.168.3.10"
RequestHeader set "x-webobjects-server-url" "http://192.168.3.10";
## When using proxy-side autentication, you need to uncomment and
## adjust the following line:
# RequestHeader set "x-webobjects-remote-user" "%{REMOTE_USER}e"
RequestHeader set "x-webobjects-server-protocol" "HTTP/1.0"
AddDefaultCharset UTF-8
Order allow,deny
Allow from all
</Proxy>
# For Apple autoconfiguration
<IfModule rewrite_module>
RewriteEngine On
RewriteRule ^/.well-known/caldav/?$ /SOGo/dav [R=301]
</IfModule>
That's it for now
> btw I'm utc+2 - I can answer only tomorrow... :))
--
*Marco
*
-------------------
[Ai sensi e per gli effetti della Legge sulla tutela della privacy
(L. 196/2003), questa mail รจ destinata unicamente alle persone sopra
indicate e le informazioni in essa contenute sono da considerarsi
strettamente riservate. E' proibito leggere, copiare, usare o
diffondere il contenuto della presente mail senza autorizzazione.
Se avete ricevuto questo messaggio per errore, siete pregati di
rispedire la stessa al mittente. Grazie]
--
[email protected]
https://inverse.ca/sogo/lists
